Question about Chevrolet Cars & Trucks

Open Question

P0700 Transmission Control System Malfunction

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: 2000 Dodge Sratus 4 speed auto transmission

Dave, The P0700 code is a generic fault code indicating the the TCM (transmission control module) has recognized a problem and the P0755 is the indicated problem. I'd recommend you check your transmission external electrical connector for water intrusion and corrosion at the terminals by disconnecting the connector. If nothing appears wrong, I'd then recommend you drop the lower transmission pan and take a look at the residue deposit that is laying on the bottom of the pan. You should only see a relativily minor amount of grayish, black clutch material residing there. Pay particular attention for a gross amount of this or any large particular material, including any metal, either filings or chunks, or any brass or aluminum. If this checks out to be fairly clean, then I'd recommend you replace that "B" solenoid (2-3 shift solenoid) and have the trans. pan and filter replaced.; I'd also highly recommend you have the trans flushed for anyother particular matter that may reside internally inside the transmission. You'll have to have the codes cleared and the transmission relearned for shift feel, at that point.

Posted on Jan 08, 2009

  • 141 Answers

SOURCE: P0700

on the fire wall . be carful you replace the tcm there is no bringing it back if you smoke that one to . remeber check for why the tcm failed!. unless you got money to burn i do not. good luck kdc744

Posted on Feb 08, 2009

csmock132
  • 4669 Answers

SOURCE: 2004 pacifica P0700 Transmission Control System (MIL Request)

You need to scan the tcm. Code p0700 in the ecm just tells you there is codes in the tcm.

Posted on Mar 12, 2009

polarcycle
  • 1392 Answers

SOURCE: 2003 Dodge Ram 1500 computer codes

P0304, could be a bad plug, bad coil, bad injector, low compression, or other stuff. The P0700, you need to look at codes in the TCM. It is telling you that the trans computer has a fault in it.

Posted on Jun 20, 2009

ZJLimited
  • 17970 Answers

SOURCE: 2005 Dodge RAM 1500 Quad

P1521 - VRIS Solenoid 1 I have replaced the VRIS (Variable resonance idle solenoid 1).
P0750 - Shift Solenoid A malfunction
There is more than one solenoid in the valve body and to make sure he is replacing the right one. I will say that with an electrical malfunction code---it's usually the wiring or the solenoid----so not a real bad choice. Come to think of it I think there will be 4 solenoids---A,B,EPC and TCC. So he needs to find out which one is the bad one before he goes replacing.

Good luck

Posted on Aug 16, 2011

Testimonial: "Thanks for the prompt and concise answer. I suspect it might possibly even a short in the system due to abuse. At least I have a starting point now!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I get code p0700 on 2004 dodge ram 1500 4.7 lt.


transmission system malfunction can be a few things the following links give some examples of different problems associated with p0700 code but more than likely if their is a noticeable problem than may have to have it diagnosed by a transmission shop
P0700 Transmission Control System Malfunction P0700 Dogge Ram Yahoo Video Search Results 2005 Dodge Ram 1500 transmission codes p0700 p0841 Transmission Automatic...

Aug 05, 2016 | 2004 Dodge Ram 1500

2 Answers

2006 Dodge stratus code p0700


code p0700 refers to transmission control system/ mil--malfunction===causes--wiring--TCM
check all wiring and connections to the transmission for water,corrosion etc
check/change the tcm ( transmission control module)

Apr 23, 2015 | 2006 Dodge Stratus

1 Answer

04 kia rio code P0700 Mil request


DTC P0700: A transmission control system problem has turned on the malfunction indicator. Probable cause:
1. Faulty sensor
2. Control unit software needs updating
3. Faulty PCM or ECM
4. Transmission system malfunction

Aug 31, 2014 | 2004 Kia Rio

1 Answer

Yellow engine diagnostic indicator light, p0700


po700 --transmission control system malfunction --your gear box or a control to the the gear box is your problem
P0700 Transmission Control System Malfunction P0700 Transmission Control System Malfunction

Apr 17, 2017 | Mercedes-Benz Mercedes Benz A Class Maisto...

2 Answers

I have a 2011 dodge caliber and it isz throw a c0700 code could u tell me what this is


P0700 DODGE - Transaxle Control System Malfunction

Symptoms - Engine Light ON (or Service Engine Soon Warning Light)
- Driveability problems
- Transaxle shifting problems

Possible causes - Shorted or open circuit within transmission control module (TCM)
- Failure of transaxle control module

Tech notes Since the P0700 is just and informative code, check the TCM for more codes to resolve the problem.

P0700 DODGE Description The transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transaxle controls.
CLEAR THE CODES AND SEE IF IT RESETS. MOST LIKELY NOT A PROBLEM

Sep 07, 2011 | 2002 Dodge Grand Caravan

1 Answer

What do i need to replace to fix error code p0700 on a 2002 dodge intrepid


(DTC) CODE # P0700....Transmission Control System (MIL Request) Translation: Transmission Control Module (TCM) Malfunction or Failure. P0700 Information Code The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM. This code is for information ONLY. If this code is present, check for transaxle codes. So basically, the P0700 code is telling you to check the TCM for a transaxle DTC. The TCM can not turn on the check engine light so it has the PCM do it.

I hope this helps....let me know if I can assist further !!

Feb 21, 2011 | 2002 Dodge Intrepid

2 Answers

Code P0700 and code P0750 what do i have too change


P0700 Transmission Control System Malfunction
P0750 Shift Solenoid A Malfunction

It seems you have a internal transmission problem, I suggest you have your transmission inspected by a reputable transmission shop.

Jun 04, 2010 | 2004 Dodge Durango

2 Answers

Code p0700


code po700 malfunction indicator lamp circuit malfunction tcm conditions. mil contoll circuit is shorted to ground .check the tcm for any codes in memory that are responsible for the request to turn on the mil lamp.tcm or trouble code malfunction has failed.

Nov 18, 2009 | 2002 Saturn VUE

1 Answer

Check engine light on 2005 town and country 3.3


(DTC) CODE # P0700....Transmission Control System (MIL Request)

Translation:
Transmission Control Module (TCM) Malfunction or Failure.

P0700 Information Code

The Transaxle Control Module (TCM) monitors the malfunction of sensors and actuators relating to transaxle control. If any malfunction is detected, the TCM informs the PCM by sending a signal (P0700 code). P0700 means that a code has been set in the TCM.

This code is for information ONLY. If this code is present, check for transaxle codes.


P1776: Solenoid Switch Valve Latched in Low/Reverse Position. The TCM monitors the L/R solenoid to ensure that the fluid transfer happens. It uses a Pressure switch to verify this. Usually this code is set by a switch that is stuck or a solenoid that is not mechanically operating.

A transmission shop would be better suited for this type of work.

Apr 11, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...