Question about 1994 Ford Explorer Limited

1 Answer

How to remove fuel line connectors - 1994 Ford Explorer Limited

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 2 Answers

There are fule line connector tools that you can get from any parts store, there are different sizes for different fule line sizes. They are not expensive

Posted on May 06, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the fuel line from the intake manifold on a Ford Ranger XLT with a 2.9 Litre engine?


Not sure what you are saying that broke.
If the line is plastic and the fitting has no place for a wrench, you use a tool made to release the spring tension inside the connector. AC lines use the same setup.
If the plastic line is broke, you may be able to get a repair kit at your local auto parts store. The fuel line is designed to be replaced all in one piece, not repaired.

Nov 25, 2015 | Ford Cars & Trucks

1 Answer

Where is the fuel pump of a ford explorer sport trac pick up located


zjlimited_701.gif

Fig. Fuel pump flange bolt torque sequence-2002 Explorer and Mountaineer and Sport-Trac Sport Built Before 03/2002

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Disconnect the battery ground cable.
  3. Relieve the fuel system pressure.
  4. Drain the fuel tank.
  5. 4WD vehicle
    1. Remove the fuel tank skid plate bolts.
    2. Remove the fuel tank skid plate rear left bolt.
    3. Remove the fuel tank skid plate rear right bolt and lower the fuel tank skid plate.
  6. All vehicles
    1. Use a suitable jack to support the fuel tank.
    2. Remove the vent hose.
    3. Remove the bolt and reposition the fuel tank support strap.
    4. Remove the support bolts and push the fuel tank back until the lip clears the support bracket.
    5. Lower the fuel tank just enough to expose the fuel lines and the fuel tank transducer connector.
    6. Disconnect the fuel line and the vapor line.
    7. Disconnect the fuel tank electrical supply connector near the frame rail. Lower the fuel tank.
  7. Clean the area around the fuel pump assembly mounting flange.
  8. Disconnect the electrical connector from the fuel pressure transducer.
    WARNING The fuel pump assembly must be handled carefully to avoid damage to the float arm and the filter.
  9. Remove the fuel pump mounting bolts and remove the fuel pump assembly.

Hope helps.

Sep 11, 2011 | Ford Explorer Sport Trac Cars & Trucks

1 Answer

How do i remove the fuel delivery and return connectors at the engine


go by the auto parts store, buy fuel line disconnect tools.you take the fuel line disconnect tool, place it on fuel line push tool in the fuel line connector to seperate fuel lines.make sure when you get ready reconnect fuel lines back together you should hear fuel line snap back in place.make sure fuel line in place dont come apart. to be on safe side dont crank car first just turn ignition to the on position for few seconds check for fuel leaks.

Jul 31, 2011 | 2000 Buick Century

2 Answers

How do i replace my fuel filter?


The fuel filter is mounted on the frame rail. There are two types of fittings used. You only need to look at the fittings to tell the difference.

There is the plastic "hair pin" type of connector. It has a plastic connector with a plastic "hairpin" clip that pushes through the connector. Just pry the clip out with a screwdriver don't worry about breaking the clip, the new filter should come with new clips. Be careful not to break the fitting though. If you break the connector, you must replace the fuel line...not fun.

The other type is what Ford calls the "Duckbill" type of connector. I don't know wht it is called that...it doesn't look like a duck bill to me. Anyway., you can identify this one as a stainless steel connector. there is usually also a stainless steel lock clip that goes over the outside of this type of connector. The lock clip can be pried up and removed with a screwdriver. Once the lock clip is removed, a special fuel line disconnect tool must be used to releasethe spring clips inside the connector. the tool canbe purchased for a couple dollars at any parts store where you would buy your fuel filter.

You need to look at the car to determine if you need the tool or not. Both types of connectors are used for the same fuel filter. Plastic connectors - no special tool needed. Stainless steel connectors - special tool required.

Mar 05, 2011 | 1997 Lincoln Town Car

1 Answer

How do you replace a fuel pump in a 1997 ford f350 crew cab


Removal & Installation 88285g11.gif

Details of the fuel pump assembly
Click to Enlarge 88285g12.gif

View of the fuel pump
Click to Enlarge

  1. Disconnect both battery ground cables.
  2. Properly relieve the fuel system pressure.
  3. Raise and safely support the vehicle securely on jackstands.

The electrical connector is located behind the fuel pump near the frame rail.

  1. Detach the fuel pump electrical connector.
  2. Remove the fuel line retaining clip and discard, then remove the fuel line from the fuel pump.
  3. Slide the clip up and off from the quick connect fitting. Insert the fuel line tool and remove the fuel pump delivery line.
  4. Unclip the brake lines from the fuel pump bracket.
  5. Loosen the pinch bolt and spread the mounting bracket.
  6. Remove the fuel pump.

To install:

  1. The installation is the reverse of the removal.

Oct 29, 2010 | 1997 Ford F350 Crew Cab

2 Answers

How do you change the fuel pump? is there a access panel and if so where is it located?


Removal & Installation
To Remove:


  1. Before servicing the vehicle, refer to the precautions at the beginning of
    this section.
  2. Release fuel pressure.
  3. Remove or disconnect the following:

    • The rear seat





      Electrical Connector
      dod_intrpd_fuel__tank_elec_conn.gif



    • The fuel pump electrical connector





      Battery Cable
      dod_intrpd_batt_conn.gif



    • Battery cable

  4. Raise and safely support the vehicle
  5. Remove or disconnect the following:





    Fuel Tank Drain
    dod_intrpd_fuel_tank_drain.gif




    • Fuel from fuel tank





      Stabilizer Bar
      dod_intrpd_stab_bar.gif








      Stabilizer Bar and EVAP Canister
      dod_intrpd_evap_cann.gif



    • The rear stabilizer bar brackets from body
    • Stabilizer bar toward rear of vehicle





      Fuel Filler Tube
      dod_intrpd_filler_tube.gif



    • The fuel filler tube from fuel tank





      Fuel And EVAP Lines
      dod_intrpd_fuel_evap_lines.gif



    • Fuel and EVAP lines

  6. Position transmission jack under fuel tank assembly.
  7. Remove fuel tank straps bolts passenger side first.
  8. Lower fuel tank and remove the purge line and vent line.
  9. Disconnect fuel line from fuel pump module by depressing quick connect
    retainers with thumb and fore finger.
  10. Slide fuel pump module electrical connector lock to unlock.
  11. Disconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.





    Fuel Tank Locknut
    dod_intrpd_fuel_tank_tool__nut.gif



  12. Use Special Tool # 6856 to remove fuel pump module locknut.
  13. Remove fuel pump and O-ring seal from tank. Discard old seal.

To Install:


  1. Wipe seal area of tank clean and place a new seal in position in the tank
    opening.





    Fuel Tank Locator
    dod_intrpd_fuel_pump_loctr.gif



  2. Position fuel pump in the tank.

    • Make sure the alignment tabs on the underside of the fuel pump module flange
      sits in the notches on the fuel tank.

  3. Position the locknut over the fuel pump module.
  4. Tighten the locknut using Special Tool # 6856

    • Torque to: 40.5 ft. lbs. (55 Nm)

    CAUTION
    Over tightening the pump lock ring may
    result in a leak.

  5. Position the fuel tank on the transmission stand.
  6. Install or connect the following:

    • Fuel pump electrical connector into hole in the body
    • The purge and vent lines
    • Fuel tank and tank straps
    • The fuel filler tube and tighten the clamp
    • The stabilizer bar and install bolts

  7. Lower vehicle.
  8. Install or connect the following:

    • The fuel pump electrical connector that is in the rear seat
    • The rear seat
    • The battery cable

  9. Fill fuel tank.
  10. Use the DRB or equivalent scan tool to pressurize the fuel system.
  11. Check for leaks.


prev.gif next.gif

Sep 23, 2010 | 1999 Chrysler Concorde

1 Answer

How to replaced fuel filter on ford f250


Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
fps23-01.jpg Disconnect the negative cable at the battery.
fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.
fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.
fps23-09.jpg Art courtesy of Delmar - Thomson Learning. Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
  • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
  • Apply a few drops of clean engine oil to the male tube ends on the filter.
  • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
  • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
  • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
  • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
  • Then, do the same with the inlet connector.
  • Now tighten the filter retaining bolt to the specified torque.
  • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter. NOTE THIS IS FOR A 3/4 TON 5.8L

May 22, 2010 | 1992 Ford F250

1 Answer

Fuel filter replacement for 2001 isuzu rodeo


Under vehicle, passenger side, below seating area, front of fuel tank, mounted on frame in fuel line

Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
fps23-01.jpg Disconnect the negative cable at the battery.
fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.
fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.
fps23-09.jpg Art courtesy of Delmar - Thomson Learning. Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
  • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
  • Apply a few drops of clean engine oil to the male tube ends on the filter.
  • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
  • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
  • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
  • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
  • Then, do the same with the inlet connector.
  • Now tighten the filter retaining bolt to the specified torque.
  • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter.

May 15, 2010 | 2001 Isuzu Rodeo

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

2 Answers

Where is the fuel filter


On buick LeSabre the fuel filter will be under the car passenger side just in front of the rear tire . Follow the fuel line and you will find it there.

Oct 05, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
1994 Ford Explorer Limited Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...