Question about 2003 Chevrolet Silverado 1500

1 Answer

Removing Oil Pan

How do I remove the oil pan? need to replace the oil pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,363 Answers

Here's a link on removing oil pan.Here's how to replace your oil pump.

Posted on Jun 01, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 105 Answers

SOURCE: oil pan removal for 1994 k1500 4WD

You should be able to drop the front drive and pull the starter you should be able to drop the oil-pan without to much trouble

Posted on Mar 25, 2009

  • 6982 Answers

SOURCE: replac 2003 monte carlo oil pan gasket

To remove the oil pan on any vehicle, first remove anything obviously in your way...starter, exhaust pipe etc. Then disconnect the engine mounts and raise engine to gain sufficient clearance between frame and pan. You cannot support the engine from under the pan so either use a fixture above the engine or put blocks between mounts and engine to support it. After all rail bolts have been removed, remember that the oil pump pickup will interfere with removal somewhat but pan can be maneuvered around it. Anything preventing you from getting the pan out will then need to be removed or moved as they are identified. Be careful when raising the engine that you do not break anything above it as it comes up.

Posted on Jun 09, 2009

  • 135 Answers

SOURCE: i am replacing the oil pump on a 98 chevy malibu,

take loose the motor mount bolt and jack the front of the engine up to clear the oil pump and remove the pan,.the bolt the runs thru the center of the mounts ,the easiest way ,hope this helps you, thanks robert b.

Posted on Jun 30, 2009

juncro
  • 467 Answers

SOURCE: My 1998 chevy s10 blazer 4x4 looks to be leaking

no special way, the oil gasket need to change

Posted on Nov 10, 2009

  • 2841 Answers

SOURCE: can i remove oil pan without removing engine 1984

Yes, you can remove the pan without removing the engine. You may have to remove anything preventing you from getting the pan out or you may have to disconnect the engine mounts and raise the engine enough to get the pan out.

Posted on Apr 18, 2010

Testimonial: "thank you this will help"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4x4 with a 5.0. How do I replace the oil pump?


You will have to remove the bolts from the engine mounts and Jack up the engine.
Remove the oil pan.
If the oil pan cannot be removed at this point you will have to remove the engine from the car.
Once the oil pan is removed the oil pump can be replaced by removing the bolts on the pump

Sep 20, 2015 | 1995 Ford Bronco

1 Answer

Procedure for removing oil pump 2001 GMC serra


The oil pump and screen should be in the bottom of the oil pan. Which would need to be removed to get access to it.

Sep 30, 2012 | GMC Cars & Trucks

1 Answer

Replacing Oil pump in Ford Expedition


the oil pump is on the crank behind the balancer and timing chain cover:


REMOVAL

1. Remove the timing chain.
2. Remove the oil pan.
3. Remove the three (A) oil pump screen and cover bolts and the (B) oil pump screen and cover.
4. Remove the two oil pump bolts and the oil pump.

INSTALLATION

1. Clean and inspect the mating surfaces.
2. Install the oil pump and loosely install the two oil pump bolts.
3. Install the oil pump screen and cover and install the three oil pump screen and cover bolts.
4. Install the timing chains.
5. Install the oil pan.

Apr 25, 2012 | 2003 Ford Expedition

1 Answer

I know it's the oil pump that needs replaced i just don't know exactly where it is.. how hard is it going to be for me to get to? What do i have to take off to get to it? Or what is the procedure...


its in the oil pan. jacking up vehicle removing oil pan , new gasket. get torx specs for oil pump bolts an oil pan bolts
ps buy a new oil pump. NEVER rebuilt one.

Jun 03, 2011 | Oldsmobile Achieva Cars & Trucks

2 Answers

NO OIL PRESSURE. 243,000 MILES. NOT OVERHEATING. SEEMS LIKE NOISE IS COMING FROM TOP OF ENGINE.


With that many miles on the engine it could be sludged up or the oil pump could be failing.

Mar 27, 2011 | Toyota Land Cruiser Cars & Trucks

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

2 Answers

Replace Oil Pump Can it be doen without pulling


Yes it can. It can be replaced from the underside by removing the oil pan

May 03, 2010 | 1998 Ford Windstar

1 Answer

Oil pump replacement


This MAY seem Strange But It IS ALL necessary for Oil Pump Replacement. And Please Don't Forget to Rate Me as Most Folks Do Not. Thank You and GOOD LUCK with the Oil Pump Job Also


OIL PUMP
It is necessary to remove the oil pan, oil pickup and chain case cover to service the oil pump rotors. The oil pump pressure relief valve can be serviced by removing the oil pan and oil pickup tube. Refer to Timing Chain Cover Removal and Installation for procedures.

DISASSEMBLY
  1. To remove the relief valve, proceed as follows:
  2. Drill a 3.175 mm (1/8 inch) hole into the relief valve retainer cap and insert a self-threading sheet metal screw into cap.
  1. Clamp screw into a vise and while supporting chain case cover, remove cap by tapping chain case cover using a soft hammer. Discard retainer cap and remove spring and relief valve.
  2. Remove oil pump cover screws, and lift off cover.
  3. Remove pump rotors.
  1. Wash all parts in a suitable solvent and inspect carefully for damage or wear.
Oil Pump Assembly
  1. Assemble pump, using new parts as required. Install the inner rotor with chamfer facing the cast iron oil pump cover.
  2. Tighten cover screws to 12 Nm (105 inch lbs.).
  3. Prime oil pump before installation by filling rotor cavity with engine oil.
  4. Install chain case cover. Refer to Timing Chain Cover Installation.
REMOVAL of Timing cover
REMOVAL
  1. Disconnect negative cable from battery.
  2. Remove timing chain cover.
REMOVAL Of Oil Pan to gain Access to OIL PUMP
  1. Disconnect negative cable from battery and remove engine oil dipstick.
  2. Raise vehicle on hoist and drain engine oil.
  3. Remove bending brace to transaxle attaching bolt.
  4. Remove bolts attaching dust cover to transaxle housing. Lower dust cover to gain access to oil pan bolts.
  5. Remove oil pan screws and remove oil pan.
INSTALLATION
  1. Clean surfaces and apply a 1/8 inch bead of Mopar (R) Silicone Rubber Adhesive Sealant or equivalent, at the parting line of the chain case cover and the rear seal retainer.
    1. Use a new pan gasket.
    2. Install pan and tighten screws to 12 Nm (105 inch lbs.).
    3. Install dust shield and bending brace to transaxle housing.
    4. Lower vehicle and install oil dipstick.
    5. Connect negative cable to battery.
    6. Fill crankcase with oil to proper level.

Mar 27, 2009 | 1998 Chrysler Town & Country

3 Answers

Replace oil pump


Oil Pump is in the oil pan.. You would have to take the pan out. To get the pan out you either have to raise the motor up or remove crossmembers.

Mar 23, 2009 | 1984 Toyota Celica Supra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...