Question about Cars & Trucks

Open Question

Slant six ignition timing

Need to know ignition timing procedure

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5252 Answers

SOURCE: 1986 dodge ram 225ci slant six and a single barrel holley carb

Start with the idle needle screw first, the idle mixture screw. Seat it all the way in, first-don't overtighten and damage it, just seat it lightly, and back out two full turns. Run the engine and set the adjustment by ear to get your best lean idle: start turning the screw in (clockwise) 1/8 or 1/4 turn at a time till engine stumbles, dies, or runs rough. Keep the engine running, and turn screw out (counterclockwise) a little at a time till you hear the idle dropping. Now between those two settings is your best lean idle. Turn the screw in, a little at a time and wait for engine to respond, tiill you get the highest idle speed. Now set the other idle screw, curb idle, to the idle setting for your truck, probably about 700 rpm. You can move back and forth between the screws to get the best steady idle. Just don't over do it on the idle mixture screw.
Good luck.

Posted on May 08, 2012

  • 599 Answers

SOURCE: locatio of oil presure gage sending unit on 1984 3.7L slant six dodge ram

below distributor

Posted on Sep 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How dose the art 105 barrel work


The Mopar slant six engines - Allpar

www.allpar.com/slant6.html
The 1977 "Super Six" with a two-barrel Carter carb compensated for smog ... Heavy-duty slant six engines used in industrial and some truck/bus (perhaps fleet as well) ...You can retrofit the double roller chain and gears into car slant sixes, .... of way to have a twin exhaust system because, man, will that do wonders for a six.

Chevrolet straight-6 engine - Wikipedia, the free encyclopedia

https://en.wikipedia.org/wiki/Chevrolet_straight-6_engine

WikipediaMany popular cars and trucks, including the Chevrolet Camaro, Chevrolet Impala, ....resulting in an unequal and unbalanced work load between the six cylinders. ... in the 261 truck engine and used triple side draft, single barrel, Carter Model YH .... The '78 Camaro had 105 horsepower (78 kW) and 190 ft·lbf (260 N·m) of ...

Dec 29, 2015 | Cars & Trucks

1 Answer

Att:ted Maxwell would a 318 bolt up to that 230 bell housing? Mind you the truck is military so everything is different and it's 24 volt system but that is not a problem


will a 318 block motor bolt up to a slant 6 bell housing for a ...

https://answers.yahoo.com/question/index?qid...
Jan 6, 2008 - I bought a 72 Dodge Scamp for my hubby and the slant 6 that is in is no good so we want to put in a 318 but we have no idea what trouble it will ...

slant six to 318...??? [Archive] - Moparchat

www.moparchat.com > ... > Technical Forums > Slant Six Chat

Nov 5, 2009 - 14 posts - ‎6 authors
You can swap in a 318 but you will need a transmission too. ... it will... That should be the A230 trans, this was made for V8s as well as sixes. ... The A903 will be marginal, even though with a bellhousing change it will bolt up. will it bolt up??? [Archive] - Moparchat - Home of ...
13 posts
May 6, 2009
3 speed manual tranny [Archive] - Moparchat - Home ...
23 posts
Mar 18, 2008
More results from www.moparchat.com

best/easiest engine swap [Archive] - Steel Soldiers::Military ...


Dec 02, 2015 | Cars & Trucks

1 Answer

Dodge dart 1973 225 slant six


Dodge dart 1973 225 slant six

Aug 20, 2014 | Cars & Trucks

1 Answer

1972 dodge dart with slant six...HELP


check the resister on the fire wall it white ceramic

Aug 21, 2012 | Cars & Trucks

1 Answer

What is the name of the manual 4 speed transmission for the 1984 dodge d100 with a 3.7 (225ci) motor, and with that trans match up to a 5.2 (318ci) motor?? thank you


The great Dodge slant 6 engine...these were very strong and dependable, i put 300,000 on a 1985 D100 and it was still going strong when i sold it. Your transmission is a "883"
Chrysler began using "833" four speeds in passenger cars in 1964. The transmission was designed by Chrysler and manufactured by New Process Gear Co. Chrysler installed the 833 four speed behind the Slant Six at two different times. The first production four speed slant sixes were the 1964-66 A-body four speed cars. The second run of production four speed slant sixes began in 1975 with the release of the Overdrive A-833. From 1975 until 1987 the Overdrive four speed was installed in slant six applications of A-bodies, F-bodies, and light trucks (D100 & D200 series trucks). These applications were not ultra rare, but the slant six four speed production figures pale in comparison to the number of V8 cars that received A-833 four speeds. Since the A-833s installed behind slant sixes were basically the same transmissions installed in the V8 cars, a slant six owner looking to install an A-833 should be familiar with all the A-833s produced, including the ones used behind V8s...There are several characteristics of the various A-833s that determine which four speeds fit in which chassis and with which engines. For the passenger cars, Chrysler manufactured two different length four speeds. The A/F-bodies received a short tailshaft A-833 and the B/C/E-bodies received a long tailshaft A-833. This difference is obvious when one of each type is sitting side by side, but either type is easily identified when it happens to be a stand alone unit.

If you are looking to replace your truck tranny, you will need to find another one out of a truck that had the slant 6 engine for it to be a direct bolt up. Chrysler made several variations.

1975 thru 1987 Overdrive 3.09:1 - 1.67:1 - 1:1 - 0.73:1 (Trucks used a 0.71:1 fourth)

Good luck, hope this helps.

Jul 11, 2011 | 1984 Dodge D150

2 Answers

1986 dodge 3/4 ton, 3.7 slant six. no fire to plugs.ignition on no blinkers or gagues, still turns over.hot to alt and coil still no fire. fuses good


Sounds like fusible link. It's a thick (thicker than normal) wire coming from battery to junction block on firewall. They burn through and/or break down internally - you can replace it with an inline 30amp fuse & holder.

Mar 25, 2011 | 1986 Dodge Pickup 4WD

1 Answer

Valve bender?


you will be good to go,the slant six was not a zero clearance engine

Jan 29, 2010 | 1983 Dodge Diplomat

1 Answer

I need to know how to reprogram a keyless entry remote for a 2003 nissan frontier..


IMPORTANT: Before entering programming mode, have in possession all of the
transmitters you will be using on the vehicle. Once you program the
transmitter, all previous codes will be erased from the memory. The other
transmitters will not be functional until you program the transmitters
again.

1. Close and lock all doors with the driver's side power lock/unlock
switch.

2. Insert key into ignition and remove it from the ignition key cylinder
at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE:
Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not
enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your
Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is
pressed more than one time, the programming
procedure will not be successful.

5. If there are any remaining transmitters (including the old ones),
unlock then lock all doors using the driver's side
power lock/unlock switch and within 5 seconds, push ANY button on the
next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing
transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock
doors using the driver's side power lock/unlock switch and open the driver
side door.

Apr 11, 2009 | 2003 Nissan Frontier Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...