Question about 2010 Toyota Auris 2.0

Open Question

Adjust rear brakes

How do I retract brake piston passenger side

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76109 Answers

SOURCE: I need to know how

If you look down at the parking brake lever from above there should be a tightning bolt to adjust the position of the lever. Never done this on Yaris, Let me know if the adjustment nut is there, if not I will check further. Thanks

Posted on Jul 31, 2008

Ad
alicantecoli
  • 22156 Answers

SOURCE: Adjusting Tacoma Rear Brakes?

yes they should be self adjusting but none of these ever work properly.The garage should have removed rear drums and cleaned them out and then rubbed down the rust lip that forms on the outside of the inside of the drum.Then cylinders checked out like you have done then shoes adjusted up till just catching on drum,this will bring the handbrake up as well.Too many know it all know nothing cowboys in this game and no govening body in any country to legislate,be different if it was solicitors .

Posted on Apr 11, 2009

c17hydro
  • 2984 Answers

SOURCE: Is there a trick to removing rear brake drums on a

The only trick is banging it off. Drums are known to be "frozen" on or stuck. Honestly, the only way to get them off when they are stuck is to carefully hammer it off. Below is what is required to remove and replace the drum....and a picture of your system:

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the wheels.
  3. Remove the brake drum from the axle hub.
To install:
  1. Install the brake drum.
  2. Install the rear wheels, tighten the wheel lug nuts.
b936120.gif

Posted on Oct 29, 2009

  • 29 Answers

SOURCE: 2003 Toyota Highlander.The brake light on the

Replace the right rear brake lamp. The bulb possible use two filaments one for brake and tail light. One burnt out filament in one bulb.

Posted on Nov 30, 2009

  • 1 Answer

SOURCE: Replaced rear brakes, Alarms still active

i have a 2003 toyota 4-runner my brake and abs vsc are on and it has a beeping loud noise.....what do u think is the problem?

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm Tryin to push Down on the rear passenger side piston on the brake caliber and it's not wanting to go down like pistons usually do


Open the bleeder valve

Use an old brake pad against the piston,
front only

Buy a 4" C-Clamp from Sears




For the Rear ----- you need a tool to turn in the parking
brake adjuster ,while pushing in Only By Hand,
bleeder open

Jun 13, 2011 | 2003 Hyundai Tiburon

1 Answer

2006 Kia Spectra 5 rear brake disc replacement


One side,turns right,and push in slightly,and the other side turns left,to retract.

Apr 20, 2010 | 2007 Kia Spectra5

1 Answer

Brakes locking up


There can be a couple of things that can cause it. If the shoes are worn too bad, the piston can expand to its furthest travel and not be able to retract. If the master cylinder is bad, it may not be letting brake fluid to return to resevoir, likewise a wheel cylinder may be scored and leaking into the drum. Loose or broken parts rolling in the brake drum may be siezing against the drum when the brakes are applied. And lastly the brake may be adjusted to tight (these have a star adjuster that tightens the brake adjuster when rolling backwards and appying the brake.) Hope this helps, Marvin

Jan 21, 2010 | 1989 Ford F 150

3 Answers

1986 Pontiac Fiero Parking Brake


it's only supposed to adjust to the point where it works...otherwise it would tighten up from use and stop you dead.

May 04, 2009 | 1986 Pontiac Fiero

1 Answer

1999 nissan quest rear brake shoes need changing


help is here:
http://autos.groups.yahoo.com/group/villagerquest/

Drum Removal
  1. Remove the rear wheel and the tire assembly. Refer to Section 204-04 .
  1. Retract the brake shoes and loosen the brake adjuster screw.
975565f.gif
  1. Remove the brake drum.
----------------------
May require big hammer to loosen drum from axle flange. Hit between the the lugs, not on them.

------------------------------------------------------------------------------
#10 is access plug to back off adjusting wheel.

f9f31b5.gif
Item Part Number Description 1 2261 Rear wheel cylinder 2 — Dust boot (part of 2128) 3 2197 Wheel cylinder piston (part of 2261) 4 — Cup (part of 2128) 5 2204 Wheel cylinder piston cup spring (part of 2128) 6 — Wheel cylinder housing (part of 2261) 7 — Brake shoe hold-down pin 8 — Access hole (part of 2212) 9 — Rear brake bleeder screw (part of 2261) 10 — Access hole plug 11 — Rear wheel cylinder bolt 12 2212 Rear brake backing plate 13 — Rear brake backing plate bolts 14 2N790 Parking brake lever clip 15 — Spring washer 16 — Secondary brake shoe and lining (part of 2200) 17 — Brake shoe hold-down spring (part of 2B514) 18 — Lower retracting spring (part of 2B514) 19 2A637 Parking brake lever 20 — Parking brake lever pin 21 2A177 Brake shoe adjusting lever 22 — Adjuster lever pin (part of 2A177) 23 — Primary brake shoe and lining (part of 2200) 24 — Upper retracting spring (part of 2B514) 25 2041 Brake adjuster screw

--------------
Shoes Removal

Take a picture and remember how each part goes and attaches
  1. Remove the brake drum, refer to Drum in this section.
  1. Remove the upper retracting spring.
  1. Remove the lower retracting spring.
  1. Remove the self-adjuster.
38bcaa0.gif
  1. Remove the hold-down springs.
  1. Remove the parking brake lever clip and the parking brake lever.

Apr 17, 2009 | 1999 Nissan Quest

1 Answer

I need a schematic for the rear brakes on an F150 super cab with 4.6L automatic trans 4wheel drive


Drum, Rear Brake System Standard Rear Brake
9969082.gif
Item Part Number Description 1 2069 Brake Shoe Hold-Down Spring Pin 2 — Rear Wheel Cylinder Retaining Bolt (2 Req'd) 3 — Washer (2 Req'd) 4 — Anchor Pin (Part of 2211) 5 — Wheel Cylinder 6 2028 Brake Shoe Anchor Pin Guide Plate 7 2A637 Parking Brake Lever 8 2296 Brake Shoe Retracting Spring (Short) 9 2296 Brake Shoe Retracting Spring (Long) 10 2200 Rear Brake Shoe and Lining (Secondary) 11 — Washer 12 2106 Parking Brake Lever Pin Retainer 13 — Brake Shoe Adjusting Lever Cable Guide 14 2A642 Primary Brake Shoe Parking Brake Lever Link 15 2A601 Parking Brake Link Spring 16 2068 Brake Shoe Hold-Down Spring 17 2A176 Brake Shoe Adjusting Lever 18 2048 Brake Shoe Adjusting Screw Socket 19 2047 Brake Shoe Adjusting Screw Nut 20 2041 Brake Adjusting Screw 21 2049 Brake Shoe Adjusting Screw Spring 22 2200 Rear Brake Shoe and Lining (Primary) 23 2A178 Brake Shoe Adjusting Lever Cable 24 2211 Brake Backing Plate
Heavy Duty Rear Brake
6dcb5d2.gif
Item Part Number Description 1 — Rear Wheel Cylinder Retaining Bolt 2 00538 Lock Nut 3 2212 Rear Brake Backing Plate 4 2262 Rear Wheel Cylinder 5 2A642 Primary Brake Shoe Parking Brake Lever Link 6 2A601 Parking Brake Link Spring 7 2A637 Parking Brake Lever 8 2106 Parking Brake Lever Pin Retainer 9 — Parking Brake Lever Bolt 10 — Secondary Shoe Assembly 11 2A179 Brake Shoe Adjusting Lever Cable Guide 12 2068 Brake Shoe Hold-Down Spring 13 — Adjusting Lever Pin 14 — Adjusting Lever Return Spring 15 2A176 Brake Shoe Adjusting Lever 16 2047 Brake Shoe Adjusting Screw Nut 17 2049 Brake Shoe Adjusting Screw Spring 18 2041 Brake Adjuster Screw 19 — Primary Shoe Assembly 20 2068 Brake Shoe Hold-Down Spring 21 2200 Rear Brake Shoe and Lining 22 2035 Brake Shoe Retracting Spring 23 2A178 Brake Shoe Adjusting Lever Cable 24 2092 Brake Adjusting Hole Cover 25 2069 Brake Shoe Hold-Down Spring Pin
The rear drum brakes:
  • Have internal shoes that expand against the brake drum (1126).
  • Are a single-anchor type.
  • Are actuated by one rear wheel cylinder (2262).
  • Have two pistons in the rear wheel cylinder (2261). One exerts force against the upper end of the primary shoe; the other exerts force against the upper end of the secondary shoe.
  • Adjust rear brake shoes and linings (2200) automatically.
  • Need manual brake adjustment if the adjusters are not operating properly or after the rear brake shoes and linings have been replaced.
When the brake pedal is applied, hydraulic fluid pressure forces the pistons in the rear wheel cylinder outward, moving the rear brake shoes and linings against the brake drum.
The rear drum brake system includes the parking brake mechanism. Refer to Section 206-05 .

Apr 04, 2009 | 1997 Ford F150 Regular Cab

1 Answer

Brakes


If its the front brakes you are working on and the piston won't retract into the caliper then you need a new caliper, or both actually. Calipers need to be replaced in pairs. If you are working on the rear then you need a special tool to turn the piston back into the caliper. you can get the rear disc brake tool at any auto parts store. Turn the piston clockwise to retract it, and pay attention to the little spots cut out of the piston that the tool grabs to turn it. They need to be at the top and bottom of the piston once you fully retract it or the little pin at the bottom of the inside brake pad wont sit against the piston. And once again if it still wont retract then you need to replace both calipers. Once you are finished you need to pump up the brake pedal and then pull up the parking brake lever and release it 10 to 20 times to adjust the piston.

Oct 22, 2008 | 1996 Saturn SL

1 Answer

Rear Brakes


If you have any flex/rubber lines at or near that rear wheel, I'd change it.

Oct 13, 2008 | 1997 Dodge Intrepid

3 Answers

Rear brakes on 1998 mercury sable


actually theres a special tool that connects to an air pump hose that expands the caliper back but you can use a vise if your very careful with pressing it back or locking clamp that you can use like a vise but this requires hand presure loosen bleed screw then use the vise

May 18, 2008 | 1998 Mercury Sable

Not finding what you are looking for?
2010 Toyota Auris 2.0 Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...