Question about 1985 Chevrolet Citation

Open Question

Removing driver side mirroe

I need to remove the driver side mirror to get at the trim underneath. I do not need to disconnect the control cable, but need free play to get the trim off. I have removed 4 screws, which has loosened it, but it appears there is something else holding it on there. Any ideas?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
pantywaste33
  • 9 Answers

SOURCE: Removal of door panel

remove the screw in the cluster( door handle, mirror, locks) careful though some of the screws are just "dummies" youll know it is if it starts stripping out. remove the big handle ( should be about two or three big screws under it and on the side where it mounts). when you do that you should be able to pull things a little better. the tricky part is getting the lock rod out of the manual lock part.but once you get it out, the door panel pops right off.

Posted on Apr 16, 2009

Ad
  • 3600 Answers

SOURCE: removing evaporator in 93 chevy pickup

Did you connect the lines? and did you break loose the tar that holds itto the car and seals the holes for the pipe? You maya have to remove the outter core cover to getto the last screws to get it out.

Posted on Jul 18, 2009

  • 69 Answers

SOURCE: How to remove/replace driver's side mirror on 96 blazer

remove door panel.. there should be access hole to get to the bolts.

Posted on Jul 31, 2009

  • 1986 Answers

SOURCE: removing door panel drivers side to connect mirror wiring behind this panel

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 14 Answers

SOURCE: removing the driver side mirror from a 2008 3/4

ok on the inside of the door at the corner where the mirror is you will see a black plastic cover. take a flat head screwdriver and slide beetween the cover and the door and pry on it. you will hear it snap but it is just the retaining clips coming out dont worry you can reuse them. once off you will see three nuts remove those nuts i think they are 10mm and the mirror will come right off. if its power there will be a wiring plug that you will have to un-couple but its pretty self explanitory after that

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

How to replace a broken wing mirror on a Volvo S40 1980 model



Power Dr Mirrors Diagnosis & Testing


Removal & Installation
Motor
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Disconnect the negative battery cable. The mirror inside cover trim The door panel The electrical connector to mirror motor The nut attaching mirror assembly to door frame The outside rear view mirror

    0900c152801c11d4.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing cover trim and nut
    Removing cover trim and nut

    0900c152801c11d5.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Removing mirrored glass from assembly
    Removing mirrored glass from assembly

  3. Remove the mirror glass:
    1. Fold the mirror glass forwards and inwards as illustrated.
    2. Grasp and pull the mirror glass lengthways until it releases.
    3. Work the glass out.

  4. Remove electric motor:
    1. Remove the 3 screws from behind the mirrored glass.
    2. Separate the connectors
      NOTE Remember the positions of the connectors.
    3. Remove the mirror motor.

      0900c152801c11d6.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Removing connectors and screws holding mirror motor
      Removing connectors and screws holding mirror motor



To install:
  1. Install or connect the following:

    The electric motor The electrical connections The 3 screws that go behind the mirror Install the terminal pins Fold out the mirror mounting on the motor Hook the mirror glass into the inner mounting Press the mirror glass into place. Place mirror in position in door

    0900c152801c11d7.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Reattaching mirror and electric motor connectors
    Reattaching mirror and electric motor connectors

  2. Install or connect the following:

    The nut attaching mirror assembly to door frame The connector The door panel The mirror inside cover trim The negative battery cable

Oct 23, 2010 | 2000 Volvo S40

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

Remove/replacing side view mirror on a jeep grand cherokee


    Remove the Old Mirror
  1. Step 1 Disconnect the negative battery cable before you take off the grand Cherokee front door trim panel. Remove all screws and clips.
  2. Step 2 Detachthe window trim cover screw, and control lever screw beforedisconnecting the entire mirror trim cover. Remove the rubber coverinside the mirror cover, and disconnect the electrical wire.
  3. Step 3 Remove three nuts from the power mirror using a Torx® star-shaped screwdriver.
  4. Step 4 Pull out the outside rear view mirror. Guide the power wire through the hole in the door.
  5. Install the New Mirror
  6. Step 1 Replace the old mirror. Put the new power mirror in place. Push the new wiring through the hole in the door.
  7. Step 2 Install and tighten the three retaining screws you took off when removing the old mirror.
  8. Step 3 Connect the power mirror wiring to the connection located on the door panel. Replace the rubber cover and interior mirror cover.
  9. Step 4 Put the front door trim panel back in place by securing all clips and tightening all screws.
  10. Step 5 Connect the Subaru Outback's battery cable to restore the power.

i will recommend i site where you will get all the information you need to remove and replace your side mirror
http://www.wjjeeps.com/mirrors.htm

Sep 10, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Replacing drivers side rear view mirro in Mitsubishi Galant 1997


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Apr 04, 2009 | 2007 Mitsubishi Galant SE Sedan

1 Answer

HOW DO I REPLACE THE DRIVER SIDE POWER MIRROR ON AN 98 F-150?


Remove the sail panel,the little panel on inside of door at the mirror.
Remove the window regulator switch plate, pry up on the front of it with a small pick or screw driver. Disconnect the electrical connectors.
Remove the top door trim panel screw that is behind the sail panel you removed.
Remove door trim panel screw at window regulator switch plate opening.
Remove door trim panel screw in the courtesy lamp housing. Remove the courtesy lamp lens.Remove the screw.
Remove the inside door handle trim cover.
Remove the bolt.
Remove the inside door handle.
Lift upward to remove the front door trim panel.
Remove the courtesy lamp.
Turn the courtesy lamp bulb socket one quarter turn and remove.
Disconnect the power mirror electrical connector.
Remove the three outside rear view mirror nuts.
Remove the mirror.

Jan 31, 2009 | 1997 Ford Expedition

3 Answers

Replacing the Mirror Light - driver's door


I assume your question is how to replace the bulb in the side mirror. Can you please tell us the make and model of the car.?
Thanks,

Jan 24, 2009 | 2002 Volvo S80

1 Answer

Driver side mirror 2004 Pontiac Grand Am


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Dec 07, 2008 | 2004 Pontiac Grand Am

1 Answer

Passengers side rear view mirro replacement


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Nov 30, 2008 | 1991 Oldsmobile Cutlass Ciera

1 Answer

Driver side mirror


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. You can then disconnect the cable running form the mirror to the control. Then you can access the bolts that secure the mirror onto the door

Nov 08, 2008 | 2006 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...