Question about 2001 Lincoln LS

Open Question

C1123 VEHICLE SPEED SENSOR SHORT TO BATTERY

THERE IS NO DIGITAL MESSAGE STORED TO INSTRUMENTAL CLUSTER SUCH AS ODOMETER, SPEED,FUEL CONSUMPTION, ETC.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 234 Answers

SOURCE: 1989 Town Car digital instrument cluster stopped

Those instrument clusters are LCD Liquid crystal display, and once they no longer work you need to get it replaced.

Posted on Oct 22, 2009

Ad
  • 25 Answers

SOURCE: My 1994 lincoln continental executive fuel/gas

fuel level sensor but rare problem if u have other problems with cluster bad ground
due to dirt.wiring is around fire wall a good day wd40 & wirebrush
u will dicover things will be working beater & some things that wernt working is now working

Posted on May 02, 2011

chico809876
  • 90 Answers

SOURCE: fuel gaue indicator does not come on Electronic

you will need a diagnostic determination whether or not it is the Instrument Panel or the fuel sending unit itsself

Posted on Dec 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Doesnanyone have a diagram showing where the wires on a speedometer connect to? I need to see if i pulled it on accident. And fuel gauge. Im learning so pictures are easier. Thx 2001 chevy tahoe


The speedometer gauge is controlled by information sent over the class 2 data bus from the PCM/ECM - engine computer . There is a VSS - vehicle speed sensor mounted on the transmission , this VSS is a input to the engine computer .
Speedometer
The IPC displays the vehicle speed based on the vehicle speed signal from the PCM. The IPC- instrument panel cluster receives the vehicle speed signal via a discreet wire. The IPC uses the vehicle speed signal circuit (4000 pulses/mile) from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 km/h (0 mph) if a malfunction in the vehicle speed signal circuit (4000 pulses/mile) exists.
Is the whole instrument cluster dead ?
Fuel Gauge
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gauge defaults to empty if:
• The PCM detects a malfunction in the fuel level sensor circuit.
• The IPC detects a loss of class 2 communications with the PCM.
When the fuel level is less than a pre-determined value, the low fuel indicator illuminates.
Reviewing the fuel system description will further explain how the system functions. Refer to:
• Fuel System Description in Engine Controls - 4.3 L
• Fuel System Description in Engine Controls - 4.8 L, 5.3 L and 6.0 L
• Fuel System Description in Engine Controls - 6.6 L
• Fuel System Description in Engine Controls - 8.1 L
Hourmeter
The IPC can display the accumulated engine run time hours using the VF display when the cluster is in the LOCK or ACC position. The IPC stores the accumulated engine run time hours in a non-volatile format. The accumulated hours will not change if the battery was disconnected or removed. When the ignition is OFF and the trip reset switch is pushed in and held for more than 4 seconds, the IPC will display the accumulated hours for 30 seconds. The hourmeter will reset to 0.0 when 10,000 hours are accumulated.
Odometer
The IPC contains a season odometer and a trip odometer. Momentarily press the trip/reset switch on the IPC in order to toggle between the season odometer and the trip odometer. Press the trip/reset switch for greater than 2 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the IPC. The IPC calculates the mileage based on the vehicle speed signal circuit from the PCM. The odometer will display 'error' if an internal IPC memory failure is detected. The odometer can be configured to display either miles or kilometers.
PRNDL Display
The IPC displays the selected gear position as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the gear position. The PRNDL display blanks if:
• The PCM detects a malfunction in the transmission range switch circuit.
• The IPC receives a class 2 message indicating the park position and the column park switch indicates a position other than park (open input).
• The IPC detects a loss of class 2 communications with the PCM.
GM had problems with stepper motors that control the needle position .
Your best bet buy a used instrument cluster from the auto slavage yard .

Apr 30, 2017 | Cars & Trucks

1 Answer

Where are all the ground wires located on a 2008 chevy cobalt?


It wouldn't be a ground problem If it were the whole instrument cluster would be dead . Checking the BCM an the IPC for DTC'S - diagnostic trouble codes is the proper way to diagnose this type problem . Not worrying about grounds .
Odometer
The vehicle odometer is calculated and stored electronically in the body control module (BCM) and is sent via the serial data circuit to the instrument panel cluster (IPC) for display. The BCM calculates and stores the mileage based on the vehicle speed serial data information from the PCM/ECM. The IPC displays the season odometer information from the BCM in the driver information center (DIC). The odometer will display error if the IPC detects an invalid odometer data from the BCM. After an invalid odometer data is received from the BCM, the IPC will display the last known odometer reading for 1.5 seconds before error is displayed in the DIC.
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed based on serial data message from the body control module (BCM). The BCM receives vehicle speed data from the PCM/ECM via the serial data circuit. The speedometer will default to 0 km/h (0 mph) if:
• The PCM/ECM detects a malfunction in the vehicle speed sensor circuit.
• The BCM detects a loss of serial data communications with the PCM/ECM.
• The IPC detects a loss of serial data communications with the BCM.

Your best bet would be to take it to the dealer !

Apr 19, 2017 | 2008 Chevrolet Cobalt

1 Answer

On a2000buick century odometer not working


You would need to take it to the dealer or someother qualified repair shop that has the diagnostic tool to check for DTC'S - diagnostic trouble codes in the instrument cluster .
DTC B0570 Season Odometer Malfunction

The instrument cluster receives a vehicle speed input from the vehicle speed sensor (VSS) over the Class 2 line. This signal is used in order to drive the speedometer and the odometer of the instrument cluster. The instrument cluster will compare the VSS data with a 16-point look-up table in order to determine needle deflection. A smooth filter is used in order to secure a continuous response. The season odometer displays the total accumulated kilometers (miles) of the vehicle. This value is permanently stored in the Electronically Erasable Programmable Read Only Memory (EEPROM) of the instrument cluster. The trip odometer displays the accumulated kilometers (miles) to the tenths of a kilometer (mile) since the last reset. This value is stored in Keep Alive Memory (KAM) of the instrument cluster.

Test Description
The numbers below refer to the step numbers on the diagnostic table.
Always perform the Instrument Cluster Diagnostic System Check before attempting to diagnose this DTC.
This diagnostic procedure requires using a scan tool.
This repair procedure requires instrument cluster replacement.
Step
Action
Value(s)
Yes
No
1
Did you perform the Instrument Cluster Diagnostic System Check?
--
YES - Go to Step 2
NO - Go to Diagnostic System Check - Instrument Cluster
2
Using a scan tool, clear the instrument cluster DTC and retest for DTC B0570.
Does DTC B0570 reset?
--
Go to Step 3
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.1L or Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.8L
3
Replace the instrument cluster. Refer to Instrument Cluster Replacement .
Is the repair complete?
--
System OK
Go to Diagnostic System Check - Instrument Cluster
© 2017 General Motors Corporation. All rights reserved.

Feb 27, 2017 | 2000 Buick Century

1 Answer

My mph, gas, and temp gauges are not working


That's why you don't let you husband work on your car ! Unless he does it for a living .. For MPH there is a VSS - vehicle speed sensor , for the gas there is a sending unit in the fuel tank, for the temp. gauge there is a temp. sensor located in coolant stream on the engine .You more then likely need to have you instrument cluster repaired . GM had a problem with step motors inside the instrument cluster . A step motor is what controls the individual gauge. The sensors are all inputs to the PCM - powertrain control module (engine computer ) .
Engine Coolant Temperature Gage
The IPC displays the engine coolant temperature as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine coolant temperature. The engine coolant temperature gage defaults to C or below if:
?€¢
The PCM detects a malfunction in the engine coolant temperature sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

Fuel Gage
The IPC displays the fuel level as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the fuel level percent. The fuel gage defaults to empty if:
?€¢
The PCM detects a malfunction in the fuel level sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

When the fuel level is less than 14% (84ohms), the low fuel indicator illuminates.
Odometer
The IPC contains a season odometer and a trip odometer. Momentarily press the trip select/reset switch in order to toggle between the season odometer and the trip odometer. Press the trip select/reset switch for greater than 1.5 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the IPC. The IPC calculates the mileage based on the vehicle speed information from the PCM. The odometer will display 'error' if an internal IPC memory failure is detected.
PRNDL Display
The IPC displays the selected gear position as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the gear position. The PRNDL display shall flash all gear positions if:
?€¢
The PCM detects a malfunction in the transmission range switch circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

Speedometer
The IPC displays the vehicle speed based on the information from the PCM. The PCM converts the data from the vehicle speed sensor to a 4000 pulses per mile signal. The IPC uses the vehicle speed signal circuit from the PCM in order to calculate the vehicle speed. The speedometer defaults to 0 mph (0 kph) if a malfunction in the vehicle speed sensor circuit exists.
Tachometer
The IPC displays the engine speed as determined by the PCM. The IPC receives a class 2 message from the PCM indicating the engine speed. The tachometer will default to 0 rpm if:
?€¢
The PCM detects a malfunction in the engine speed sensor circuit.


?€¢
The IPC detects a loss of class 2 communications with the PCM.

May 22, 2016 | 2002 Buick Century

1 Answer

I have a 2010 Chevy impala LS instrument cluster and it has a 20 pin plug I'm trying to figure out which wire's on the back of the cluster are for the speed sensor, rpm, gas, and temp wires.


Boy your way off base . All the gauges are inputs from the ECM - engine computer . The VSS - vehicle speed sensor , ETC - engine coolant temp sensor , sending unit in the fuel tank , All this sensors input the engine computer . The PCM then sends this info on the GMLAN serial data bus ,communications network . The Instrument cluster has a microprocessor inside that translates this info an controls the gauges. You probably have an instrument cluster problem or a communication network problem . Your best bet is to take your vehicle to the dealer or some other qualified repair shop. Need to have it checked for DTC'S - diagnostic trouble codes.
Indicators and Warning Messages
Refer to Indicator/Warning Message Description and Operation.
Engine Coolant Temperature Gage
The instrument panel cluster (IPC) displays the engine coolant temperature as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the engine coolant temperature. The IPC receives the coolant temperature information via serial data message from the body control module (BCM). The engine coolant temperature gage defaults to 60?°C (140?°F) or below if:
?€¢
The ECM detects a malfunction in the engine coolant temperature sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.
Fuel Gage
The instrument panel cluster (IPC) displays the fuel level as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the fuel level percent. The body control module (BCM) sends the fuel level information from the ECM to the IPC via a serial data message indicating the fuel level percent. The fuel gage defaults to empty if:
?€¢
The ECM detects a malfunction in the fuel level sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.
When the fuel level is less than a pre-determined value, the low fuel indicator illuminates in the IPC.
Odometer
The vehicle odometer is calculated and stored electronically in the instrument panel cluster (IPC). The IPC contains a season odometer and trip odometer A or B. Momentarily press the trip/fuel button in order to toggle between the season odometer and the trip odometer. Press the set/reset button for greater than 0.25 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The IPC displays the vehicle mileage and trip mileage as determined by the engine control module (ECM). The IPC calculates the mileage based on the serial data vehicle speed information from the ECM. The odometer will display 'error' if an internal IPC memory failure is detected. The odometer displays either miles or kilometers and can be set through the customization menu in the driver information center (DIC).
PRNDL Display
The instrument panel cluster (IPC) displays the selected gear position as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the gear position. The PRNDL display blanks if:
?€¢
The ECM detects a malfunction in the transmission range switch circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the body control module (BCM).
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed as determined by the engine control module (ECM). The IPC calculates the mileage based on serial data vehicle speed information from the ECM. The IPC receives vehicle speed information from the body control module (BCM) via a serial data message. The speedometer defaults to 0 km/h (0 mph) if the IPC detects a loss of serial data communications with the ECM or BCM.
Tachometer
The instrument panel cluster (IPC) displays the engine speed as determined by the engine control module (ECM). The IPC receives a serial data message from the ECM indicating the engine speed. The IPC receives the engine speed information from the body control module (BCM) via a serial data message. The tachometer will default to 0 RPM if:
?€¢
The ECM detects a malfunction in the engine speed sensor circuit.

?€¢
The IPC detects a loss of serial data communications with the ECM.

?€¢
The IPC detects a loss of serial data communications with the BCM.

How to Diagnose Controller Area Network CAN Suggest you read up on C.A.N.

May 14, 2016 | Cars & Trucks

1 Answer

While driving antitheft light comes on and all the gauges go flat,car keeps runnig,want to disable system,not sure what to look for


Before doing something drastic ,have it checked out for DTC'S - diagnostic trouble codes . It may not be the anti-theft system ,gauges going flat would be more like a communication problem between modules . PCM / BCM / instrument cluster etc.. That also could cause theft light coming on . If your not sure what to look for ,take it to a ASE certified professional . You may render your vehicle useless if you don't know what your doing .
Serial Data Power Mode Master
On vehicles that have several control modules connected by serial data circuits, one module is the power mode master (PMM). On this vehicle, the PMM is the body control module (BCM). The PMM receives 3 discrete ignition switch signals to differentiate which power mode will be sent over the Serial Data circuits. The 3-wire Ignition Switch table below illustrates the state of these inputs in correspondence to the ignition switch position:
Serial Data Messages The modules that depend exclusively on serial data messages for power modes. stay in the state dictated by the last valid PMM message until they can check for the engine run flag status on the serial data circuits. If the PMM fails, the modules monitor the serial data circuit for the engine run flag serial data. If the engine run flag serial data is True, indicating that the engine is running, the modules fail-safe to RUN. In this state, the modules and their subsystems can support all operator requirements. If the engine run flag serial data is False, indicating that the engine is not running, the modules fail-safe to OFF-AWAKE. In this state, the modules are constantly checking for a change status message on the serial data circuits and can respond to both local inputs and serial data inputs from other modules on the vehicle.
Indicators and Warning Messages
Refer to Indicator/Warning Message Description and Operation .
Engine Coolant Temperature Gage
The instrument panel cluster (IPC) displays the engine coolant temperature as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the PCM/ECM indicating the engine coolant temperature. The engine coolant temperature gage defaults to 38?°C (100?°F) if:
?€¢
The PCM/ECM detects a malfunction in the engine coolant temperature sensor circuit.


?€¢
The IPC detects a loss of serial data communications from the BCM.

Fuel Gage
The instrument panel cluster (IPC) displays the fuel level as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the body control module (BCM) indicating the fuel level. The fuel gage defaults to E (empty) if:
?€¢
The PCM/ECM detects a malfunction in the fuel level sensor circuit.


?€¢
The IPC detects a loss of serial data communications from the BCM.

When the fuel level is less than 14 percent, the low fuel indicator illuminates.
Odometer
The instrument panel cluster (IPC) contains a season odometer and a trip odometer. Momentarily press the trip/reset switch in order to toggle between the season odometer and the trip odometer. Press the trip/reset switch for greater than 2 seconds, while the trip odometer is displayed, in order to reset the trip odometer. The odometer is calculated and stored electronically in the body control module (BCM). The BCM uses the vehicle speed information from the powertrain control module (PCM) to calculate the odometer. The odometer displays 'error' if an internal IPC memory failure is detected. The IPC stores a backup copy of the odometer value incase the IPC stops receiving a valid odometer value from the BCM.
Speedometer
The instrument panel cluster (IPC) displays the vehicle speed based on the information from the ECM/PCM. The IPC receives the vehicle speed information from the BCM via the serial data circuit. The speedometer defaults to 0 kmh (0 mph) when the following occurs:
?€¢
The powertrain control module (PCM) or the engine control module (ECM) detects a malfunction in the vehicle speed sensor circuit.


?€¢
The IPC detects a loss of serial data communication from the BCM.

Tachometer
The instrument panel cluster (IPC) displays the engine speed as determined by the powertrain control module (PCM) or the engine control module (ECM). The IPC receives a serial data message from the body control module (BCM) indicating the engine speed. The tachometer will default to 0 RPM if:
?€¢
The PCM/ECM detects a malfunction in the engine speed sensor circuit.


?€¢
The IPC detects a loss of serial data communication from the BCM.

Apr 07, 2016 | 2006 Pontiac G6

1 Answer

2000 GMC Jimmy 4×4 The ABS light is on, the speed odometer does not work, and it does shift out of 1st gear, if I manually put it into second gear then it will shift fine, it has a changed VSS


Did you have it check for DTC'S - diagnostic trouble codes ?
Speedometer
The speedometer is an analog gauge that is located in the instrument cluster. The PCM/VCM receives an analog input from the vehicle speed sensor and converts it to a digital signal containing 4,000 pulses per mile (PPM) for the instrument cluster.
The PCM/VCM sends this digital output (4,000 PPM) to the instrument cluster on a designated circuit. These pulses can be measured in Hertz (Hz) using a digital multimeter (DMM) on the AC scale. The PCM/VCM calibration is matched to the final drive and tire size of each vehicle. If the final drive or tire size is changed for any reason, the PCM/VCM must be updated in order to match the new final drive or tire size. If not, the signal will not be accurate for proper speedometer/odometer operation. An incorrect signal can affect the antilock brakes and the cruise control systems.
The speedometer system consists of the instrument cluster, vehicle speed sensor (VSS), PCM/VCM and related wiring. The VSS is a permanent magnet signal generator that sends an analog signal proportional to the propeller shaft speed to the PCM/VCM. The VSS mounts to the transmission tailshaft extension housing on 2-wheel drive (2WD) models and the transfer case output shaft housing on 4-wheel drive (4WD) models.
Repairs to the instrument cluster can only be performed by an authorized instrument cluster service center. DTC P0502 Vehicle Speed Sensor (VSS) Circuit Low Input and DTC P0503 Vehicle Speed Sensor (VSS) Circuit Intermittent in Automatic Transmission - 4L60-E
- DTC P0500 Vehicle Speed Sensor (VSS) Circuit in Engine Controls - 4.3L Important: If the instrument cluster is completely inoperative, refer to Instrument Cluster Inoperative .
Install a scan tool.
Raise the vehicles drive wheels. Refer to Lifting and Jacking the Vehicle in General Information.
Start the engine.
Place the transmission into drive for automatic transmission and third gear for manual transmission.
Compare the displayed vehicle speed on the Instrument Cluster with the monitored speed on the scan tool.
Does the vehicles speedometer and the scan tool both display 0 km/h (0 mph)? You really need a Factory scan tool or equivalent to check this . The VSS is an input to the PCM/VCM . engine computer . You can test with a DVOM - digital volt ohm meter , for signal to engine computer .
I know most people don't like hearing this , but I suggest you take it to a ASE certified repair facility .

Feb 21, 2016 | GMC Cars & Trucks

1 Answer

After disconnect and reconnect the battery of my opel antara, the indication of odometer displays only 888... for all indications. How can i reset it?


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2007 Opel Antara 2.0

1 Answer

My nissan Almera S reg has no side lights or dash lights.All fuses seem ok.


This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Sep 10, 2012 | 2005 Nissan Almera 1.5

1 Answer

Changing dashboard light


Hi,

This solution will be of great help to you,even in the case of future or other dashboard problems;
Instrument cluster consists of electronic analog gauges, various warning lights, and optional tachometer. Vehicles equipped with tachometer have an electronic vacuum fluorescent transmission range indicator (PRND3L),odometer and trip odometer display. Vehicles without tachometer are equipped with a cable-operated transmission range indicator.
Instrument cluster is equipped with the following warning lights:
Battery voltage.
Cruise (speed control).
Door ajar.
Fasten seat belt.
Lift gate ajar.
Low fuel level.
Low windshield and washer level.
Traction Control.
The Body Control Module (BCM), which receives input from various sensors, sends display information to instrument cluster and operates gauges. Instrument cluster incorporates a self-test diagnostic feature to identify electronic problems. BCM, Powertrain Control Module (PCM), and Transmission Control Module (TCM) are continuously monitored by the diagnostic system.

SELF-DIAGNOSTICS
With ignition off, press and hold TRIP and RESET buttons while turning ignition switch to ON position. Continue to hold TRIP and RESET buttons until odometer window displays CODE (approximately 5 seconds). If problem exists, system will display diagnostic trouble codes. See DIAGNOSTIC CODE CHART table. If no problem exists, Code 999 (end test) will be displayed.
DIAGNOSTIC CODE CHART
CodeDescription
110.......Cluster Memory Fault
111.......Cluster Calibration Fault
905.......No CCD Bus Message From TCM
921.......Odometer Fault From BCM
940.......No CCD Bus Message From PCM

After diagnostic code display ends, instrument cluster will go into each of the following tests in order:
Dim test.
Calibration test.
Odometer segment test.
Electronic Transmission Range indicator segment test.
Dim Test
CHEC-0 will be displayed in odometer window. Instrument cluster will dim Vacuum Florescent (VF) display. If VF displays do not dim, a problem in instrument cluster exists. See BODY CONTROL COMPUTER TESTS in BODY CONTROL COMPUTER article.
Calibration Test
CHEC-1 will be displayed in odometer window. Each of instrument cluster gauges will move sequentially through each calibration point. See GAUGE CALIBRATIONS table. If gauge needle is not calibrated properly, a problem in instrument cluster exists.

Odometer Segment Test
CHEC-2 will be displayed in odometer window. Each segment of odometer will light sequentially. If any segment does not light, replace instrument cluster.
Electronic Transmission Range Indicator Segment Test
CHEC-3 will be displayed in odometer window. Each segment of electronic transmission range indicator will light sequentially. If any segment does not light, replace instrument cluster.

Aug 09, 2010 | 1998 Plymouth Voyager

Not finding what you are looking for?
2001 Lincoln LS Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

fordexpert

Level 3 Expert

5537 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...