Question about 2009 Toyota Venza

Open Question

How to replace front wheel stud - 2009 Toyota Venza

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 36 Answers

SOURCE: snapped wheel studs on front wheels and need to change them

you have to hammer the studs through the spindle to get them out. then **** the new ones in with a nut and lots of washers. put grease on the washers and threads before you **** the studs in.

Posted on Apr 15, 2009

hightower680
  • 76 Answers

SOURCE: how do i replace wheel stud on 88 corolla? front

you will have to take the disc and caliper off too.
Then put the wheel nut back on, screw the nut until the top is level with the thread on the stud. A few good hits should do it, when you put the new one in put a few washers on the stud, then put the nut on and tighten up just so the stud is in right.
Here is a diagram will show you the stud.
i hope this helps!


6611148.gif

Posted on Jul 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace front wheel studs on 2011 Kia Forte


If you can find just the studs and not have to buy the whole hub assembly, screw a lug nut on flush to the stud and drive it out with a hammer, make sure its in a position to have room on the back side. Put in new stud and with a few spacers tighten a lug nut to seat it.

Aug 15, 2014 | Cars & Trucks

1 Answer

Replace right front wheel stud


If it is just one stud,it's best to leave it be,I have a 85 Nissan 4x4 and one stud is stripped and I have a repair manual and with it being a 4x4,there is a lot of parts to be remove to get to the stud and it may effect my 4x4ing if something doesn't go back just right.I found a repair guide for yours but it doesn't go into detail.It's best to have a repair manual for this so you will know how everything goes back.

Feb 08, 2013 | Nissan Cars & Trucks

2 Answers

2000 Dodge Caravan....broken wheel studs...


Yeah , it's a fairly simple repair, All the wheel studs must be replaced and lug nuts also.Closely examine the wheel or get competent tyre replacement company to double check for damage ! Remove the brake disc caliper and brake disc itself (usually 2 cross head screws) , tap off (gently) it may be stuck thru corrosion / rust etc , Broken studs can be knocked out(towards drive shaft ) of the hub assy with a suitable drift and hammer (splined into hub) . The studs are a servicable replacement part. Check all other wheel nuts as this is usually a result from poor fixing or wheel replacement recently .. Good luck

Apr 05, 2010 | 2000 Dodge Caravan

1 Answer

Front wheel stud replacement for a 2006 Hyundai Sonata GL.


grind a flat spot on the round head of the new stud this should give enough clearance to install it. don't pull the hub this will damage the bearing.

Oct 24, 2009 | 2006 Hyundai Sonata

1 Answer

Sheered off stud. Easily replaced or whole new wheel hub assy?


Should be able to have the peice of stud that is left in the tire taken out and a new stud pressed in!!

Sep 24, 2009 | 2006 Chevrolet Uplander

3 Answers

Broken stud on wheel


The studs press out and in. Perhaps a hammer would work. Replacements studs can be purchased. Need to remove hub, of course.

Aug 13, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Broke stud on front left side


Yes you can replace the broken wheel stud. The wheel studs are pressed into place, and a vise will work to press it out, and in. You will have to remove the wheel hub, and then use a deep well socket and a bolt or something smaller than the actual stud to remove it with a vise. To replace it, you will need to use the deep well socket on the thread side of the stud, and press the new one in with the vise.

I hope this helps you, and I wish you luck with your repair.

Apr 25, 2009 | 2003 Pontiac Sunfire

2 Answers

2003 hyundai elantra gls front wheel stud broke


grab a large punch and hammer and knock out the old broken one. Push the new one in and re tighten. This will pull it into place and because it has splines it should not spin while doing so.

Apr 05, 2009 | Hyundai Motor 2003 Elantra

1 Answer

1990 Sentra How it remove and replace lug studs on front wheel


there is a large nut that holds that hub on. Remove the cotter pin and the cap from the bolt... remove the bolt and the hub comes off.

Robert

Feb 27, 2009 | 1990 Nissan Sentra

1 Answer

Wheel stud


I have replaced one of mine, you have to buy a stud that has tapered serrations, remove the disc and hammer out the old and hammer in the new replacement.

Jul 30, 2008 | 1996 Honda Civic

Not finding what you are looking for?
2009 Toyota Venza Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...