Question about 2008 Toyota Yaris 1.3

Open Question

Toyota 120 amp fuse

Change 120 amp fusible link

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 48 Answers

SOURCE: Removing the 100 amp fuse link in a 1994 toyota corolla

the fuse link is bolted in from the two side in the fusebox.you have to un bolt the whole fusebox so you can raise it and if you look at the sides there are two side panels that can be moved down so you can get a socket or spanner on the two bolts apprx 10mm. undo them and raise the fuse out and put the new one in and tighten up the bolts again. hope this helps.

Posted on Apr 25, 2009

kamakani
  • 104 Answers

SOURCE: 2006 Toyota Tacoma, power outlet/cig lighter not working

I am not sure about "fusible link", But the suggeation I can give you is to open dash or where the outlet is located and check the wires in the back of outlet with a light tester.

Posted on Jun 03, 2009

superjorge1
  • 8 Answers

SOURCE: Toyota Avalon 120 amp main fuse removal.

you have to loosen the mounting bolts on the fuse panel and on the bottom side the fuse is held in by 2 8 millimeter bolts.

Posted on Nov 17, 2009

Testimonial: "Very helpful and exactly right. Saved my neighbor a towing charge to the dealer. His car is back up and running. Thank you!!! "

ZJLimited
  • 17970 Answers

SOURCE: how do i replace a 120 amp fuse step by step on a

There are several fuse blocks. They are located in the engine compartment, behind the right side kick panel, under the instrument panel or behind the left side kick panel.

REPLACEMENT
If any light or electrical component in the vehicle does not work, its fuse may be blown. To determine the fuse that is the source of the problem, look on the lid of the fuse box as it will give the name and the circuit serviced by each fuse. To inspect a suspected blown fuse, pull the fuse straight out with the pull-out tool and look at the fuse carefully. If the thin wire that bridges the fuse terminals is broken, the fuse is bad and must be replaced. On a good fuse, the wire will be intact.

Sometimes it is difficult to make an accurate determination. If this is the case, try replacing the fuse with one that you know is good. If the fuse blows repeatedly, then this suggests that a short circuit lies somewhere in the electrical system and you should have the system checked.

544e23d.jpg

Fig. Once the cover is removed from the fuse box, you can identify each fuse and relay

73828f0.jpg

Fig. All circuit breakers and fuses pull out quick easily

When installing a new fuse, use one with the same amperage rating as the one being replaced. To install the a new fuse, first turn off all the electrical components and the ignition switch. Always use the fuse pull-out tool and install the fuse straight. Twisting of the fuse could cause the terminals to separate too much which may result in a bad connection. It may be a good idea to purchase some extra fuses and put them in the box in case of an emergency.

b7627a0.jpg

Fig. Relays can be removed by pulling them from the block

I hope helps with this (remember rated this help) Good luck.

Posted on Dec 28, 2009

  • 184 Answers

SOURCE: 1992 Toyota Camry won't crank

Check the ground cable going from the battery to
alternator, then to chassis. Make sure there is no
rust at the chassis ground wire terminal, and that it
is very tight. The fusible link will be off the alternator
red power cable,usually, but not 100% on that car.
Good luck.

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1990 Toyota truck 22re motor no headlights, dash lights, battery is new starter and alternater are good, unable find fusible links, please help


I don't have a wiring diagram but as I recall it has a fuse for each headlight 10amp, a headlight relay and it has to have a good high low beam switch to function as well as a good headlight switch. Good luck

May 31, 2015 | Toyota Cars & Trucks

1 Answer

Not sure what the 120 amp fusible link socket should look like.


If anyone can figure it out (besides the dealer) it will be AutoZone. I carry any problem that I can't figure out to them and they will keep on until they figure it out. If they can't then you will have to take it to a dealer, which I know ou don't want to.

Mar 09, 2014 | 1991 Dodge Stealth

1 Answer

Fusible link toyota starlet


Blown fusible link can be the problem.Take all the fuses out and spray contact clean on all fuse connections ,then reinstall fuses after a light sanding with fine sand paper.You can make a new fusible link by wiring in an inline fuse.If you don't know the amperage of the blown fusible link,go with a 20 amp fuse if it's for the lights.
Nice car.

Jun 01, 2017 | 1978 Toyota Starlet

1 Answer

1989 TOYOTA 4X4 WONT START NO SPARK


Often its the igniter, the ignition control module, located, I think, on the firewall driver's side. Did you check for codes by jumping "t" and "e1" on your little diagnostic connector(same location as igniter-lift cover on little box, diagram of pin #'s is on top of cover). You'll have to watch your cel light on dash to record codes.
Also check your fuses and relays in the little black box by your battery (efi fuse, main relay, the 30 and (40 or60) amp AM1 &AM2 fuses). Good luck. Oops, also I think there is a fusible link near your batt. but if it cranks over, it wouldn't be the fusible link.

Oct 22, 2011 | 1989 Toyota Pickup SR5

1 Answer

I put my battery in wrong in my 95 avalon now nothing happens when I trun the key, whats wrong?


It all depends on how lucky you are today. Connecting the battery backwards can destroy some high-dollar stuff. If you are really lucky, you will only have a blown fuse (or fuses). Check both of your main fuse blocks on the left side of the engine compartment,
One of the boxes is called the "Fusible Link" box and the other is called the "Engine Compartment Junction Block" (J/B) (See picture below).
Your main circuits are protected by the 40 Amp and 80 Amp fusible links in the Fusible Link box and the 120 Amp Alternator Fuse in the Junction Block. You will most likely find one or more of these fuses/fusible links blown.

Sep 19, 2011 | 1995 Toyota Avalon

2 Answers

How remove f link from fuse box in 97 corolla


Hi. The fusible links are the big fuses located in the fuse box. The exact location of the fuses depend on the engine and on the version of the car. In 1997 Toyota built series
7 Corolla. At the end of 1997 Series 8 was introduced. in the year 1997 both models with different engines were distributed. There are up to 4 fusible links (big fuses ranging from 30 Amp towing protector to 100 Amps) See here.
Low amps fusible links are also in passenger compartment.
The fusible links are simply fuses and can get replaced using long nose pliers.

Below I have published the fuse diagrams covering Toyota series 7 (1993 to 1997) models.

The fusible links can be purchased here.
The site also includes schematics.

In case the car is a series 8 (late 1997), here service manual for series 8.

ginko_139.jpg

Here a fuse link for Corolla 1997, color may vary depending on amps, the one below is low amp current 30A, 100A is usually blue and 40A green, there may be black fuses with no color code:

ginko_140.jpg

Aug 27, 2011 | 1993 Toyota Corolla

2 Answers

Location of the 120 amp main fuse on a 2002 ford expedition


Look under the hood. The fuse is not a fuse as such, but a fusible link. It will look like a rubber piece over a wire with an amperage rating embossed on it.

Jun 26, 2011 | Ford Expedition Cars & Trucks

2 Answers

1992 toyota pickup will not start no lights anywhere battery has 12.5 volts any thoughts?


check the wire going to the ignition switch or the 80 amp fuse is blown in the hood fuse box.

Jun 14, 2010 | 1992 Toyota Pickup

1 Answer

92 toyota paseo alternator not charging


you may have missed a fuse or fusible link , there is a 100amp alternator fuse and a 50 amp fuse on that circuit , location of those 2 fuses are (left side of engine compartment) also there is a fusible link in that circuit right off the positive side of the battery , those big fuses don't look anything like a normal if that helps , cheers'

Jan 13, 2009 | 1992 Toyota Paseo

Not finding what you are looking for?
2008 Toyota Yaris 1.3 Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...