Question about 2003 Toyota Camry

Open Question

Replace front wheel bearing assembly only on 2003 camry

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 373 Answers

SOURCE: wheel bearing

HI, For replace the front wheel bearing. on a toyota corolla 03
You need a hydrualic bench.
Because they goin pressed.
I recomend go to a repair shop, is not easy.
It's take about 2 hour to do. with the right tools.

Posted on Jul 04, 2008

Ad

SOURCE: 2000 toyota echo, wheel bearings

I found this site to be very helpful with this job: http://www.toyotanation.com/forum/showthread.php?s=714b28cb1c3f77f992209de0bdbfbd13&p=2481776#post2481776

Posted on Sep 23, 2008

  • 40 Answers

SOURCE: Replacing front wheel bearing

it is a bit of a job. You need to remove the the axle nut, caliper and rotor and seperate the tie rod and balljoint from the steering knuckle. Then undo the two strut bolts. The wheel bearing is pressed into the hub and will be difficult to remove with out a press of some sort. Either way the bearing is removed and installed one way. There will be a large snap ring you will need to remove and then the unit will press out the side you removed the ring from. You may be able to rent a press or a kit that allows you to skip a few steps, but if you have a vise, a large hammer and an extension and large socket you should be able to force it out. But not rcommended for install. Hope this helps

Posted on Apr 15, 2009

blueextc3221
  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

  • 18 Answers

SOURCE: wheel bearing replacement left front

Diagnosing the bearings can be tricky depending on severity of wear. Typically - drone noise at highway speeds, squeeling, clicking or grinding noises at low speeds that reduce during braking, or pull off the wheel and brake assembly and check the bearing for slack or smoothness of rotation by hand. While doing this, check the brake assembly thoroughly - generally a more likely culprit of wheel noise.

Wheel bearing replacement is not for the novice backyard mech. - you will need pullers, press, etc. If you can get a rebuilt assembly - much easier.

Posted on May 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 Toyota 4 runner 2 wd front wheel removal


Install front wheel bearing hub assembly on a ... - YouTube

? 8:42
https://www.youtube.com/watch?v=LQ-DGdt2J2U
Mar 11, 2014 - Uploaded by Andy Taylor
... Install front wheel bearing hub assembly on a 2003-2014Toyota 4Runner .... Pressing a 2005 and up Toyota Tacoma,4Runner, FJ Cruiser 2WD or 4WD ... How to Remove & Replace a Toyota 4x4 Manual Locking Hub ...
images for 99 Toyota 4 runner 2 wd front wheel removal

Nov 26, 2015 | Toyota Cars & Trucks

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

How to replace front wheel bearing on 2003 kia sedona


Disassembly 1. Remove oil seal from front wheel hub. 2. Remove front wheel hub assembly with suitable tool.

bi6c021a.gif 3. Remove retaining ring. note_icon_eng.gif If the bearing inner race remains on wheel hub, grind a section of inner race until approximately 0.020 in (0.5 mm) remains. Remove race with a chisel.

bi6c021b.gif 4. Remove wheel bearing with suitable tool.

bi6c021c.gif note_icon_eng.gif Do not remove dust cover unless necessary. Do not reuse dust cover if removed. 5. Mark relative positions of dust cover and knuckle for proper reassembly. 6. Remove dust cover with a chisel.

ai2a023c.gif note_icon_eng.gif Do not remove wheel hub bolt unless necessary. Do not reuse wheel hub bolt if removed. 7. Remove wheel hub bolt with a press.

bi6c021d.gif Assembly 1. Press in new wheel studs. note_icon_eng.gif Front wheel hub press in either bolt turning or loosening by the torque of 108.5 lb•ft (147 N•m, 15 kg•m) shall not be premissible.

bi6c022a.gif 2. Mark new dust cover to match the removed dust cover. 3. Align mark on new dust cover with knuckle. 4. Install new dust cover with suitable tool.

bi6c022b.gif 5. Install new wheel bearing with suitable tool. 6. Install front wheel hub assembly with suitable tool.

bi6c022c.gif note_icon_eng.gif Use a new oil seal, and apply grease to seal. Install oil seal so that it is flush with knuckle. 7. Install new oil seal with SST(0K993 331 016).

bi6c022d.gif

Jan 12, 2013 | 2003 Kia Sedona

1 Answer

Front wheel assembly diagram


For front wheel assembly diagram and replacement,click the link below and go through procedure:----Front wheel hub assembly Diagram and replacing procedure? http://howtobyme.blogspot.in/2012/02/front-wheel-hub-assembly-diagram-and.html
----------Front wheel assembly diagram to replace wheel bearing? http://howtobyme.blogspot.in/2012/02/front-wheel-assembly-diagram-to-replace.html
-------------How to replace Front wheel bearing? http://howtobyme.blogspot.in/2012/02/how-to-replace-front-wheel-bearing.html
-----------Check all 3 links one by one.This will help.Thanks.

Feb 22, 2012 | Ford F-250 Cars & Trucks

1 Answer

Replace front hub assembly.


Replacing the front wheel bearing/hubs can be a big job for the inexperianced. Briefly...
Remove tire/wheel
Remove brake caliper assembly, do not remove brake line.
Remove caliper bracket.
Remove brake rotor.
Unplug ABS sensor.
Remove the large axle nut.
Press axle out of bearing (may need special tool)
Remove the 3 bearing bolts and remove bearing.

May 19, 2010 | 2003 Chevrolet Impala

1 Answer

2wd front wheel need to replace bearings or hub assembly which is best


A Front Wheel Drive Vehicle Can Have Two Types Of Rear Wheel Bearings: Serviceable Bearings, Or Nonserviceable, Sealed Bearings. When Sealed Bearings Fail, The Bolts Holding The Bearing And Hub To The Axel Or Control Arm Must Be Removed. When Installing The New Bearing Assembly, Torque The Bolts To Specifications.Some Manufacturers require The Use Of New Fasteners When Rear Bearings And Hubs Are Replaced.

When A Serviceable Wheel Bearing Is Used, The Bearing Can Be Disassembled And Packed With Grease.It Is Serviced Like A Front Wheel Bearing On A Rear-wheel-Drive-Car.

Apr 09, 2010 | 2003 Ford Explorer Sport Trac

1 Answer

Replacing front wheel bearings on a 2004 Suburban


The front wheel bearings are sealed units, and must be replaced with the entire hub assembly. They do not need periodic cleaning/replacing as they did in the old days, if they are not making noise do not bother with them.

Apr 07, 2010 | 2003 Chevrolet Suburban 1500

1 Answer

What does it take to replace the front wheel bearings on a 2003 Tiburon


the front wheel bearings on your car are not sold except as a front wheel hub assembly with the bearing pre-installed, they run about $100.00 each, to replace them requires no special tools, all u do is remove the wheel, the brake caliper and the brake rotor and the hub nut, then the hub just slides off, u will most likely need a very large socket for the hub retaining nut.

Jul 05, 2009 | 2003 Hyundai Tiburon

2 Answers

My camry is making a loud whining noise. I took it to a mechanic and he said it was probably the front bearings. The noise only happens when the wheels are spining. My question is how do I replace these....


Hi there. Most, if not all front wheel bearings these days are pressed into the front wheel hub assembly and to replace these is not normally a DIY job. Because new bearings need to be pressed into the hub assembly, a machine shop press ought to be used and the job undertaken by competent individuals. My advice if you do intend undertaking the work yourself is to remove the hub assembly and then have a machine shop operative remove the old bearings and have the new bearings pressed-in for you. Hope this helps, Scottech.

Jul 02, 2009 | 1996 Toyota Camry

1 Answer

Wheel bearings


it is a bearing and hub assembly, average price is around $200 US
There are 2 designs, the cheaper ones have external ABS sensor, the more expensive has ABS sensor built into the hub assy..
here is a picture of the hub assy w/built in ABS sensor.
642ae2b.jpg

Mar 09, 2009 | 2003 Jeep Liberty

Not finding what you are looking for?
2003 Toyota Camry Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...