Question about Dodge Ram 2500

Open Question

How to remove the PDM Box from an 04 Dodge Ram 2500

Typical Dodge running light failure AGAIN! Checked all circuits and the problem is more than likely corrosion on the board. I am wanting to know how to remove the fuse box? All I see is a cheap plastic phillips head at the base and x1 3/8 bolt mounting to truck...I see there are also x2 plastic flat head type anchors going into the battery box, do these come off somehow? (I tried to loosen them and slide over and thru the battery box with no luck). Thanks

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 113 Answers

SOURCE: how do I remove the drivers front fender of a 1994 Dodge Ram 2500

yes undo your battery as ans air bag has a connector on the seat and if unplugged could cause air bags to go off with battery still hooked up leat sit for five min. should be four bolts or nuts holding seat down

Posted on Sep 15, 2009

  • 83 Answers

SOURCE: 2006 Dodge Ram 2500 diesel truck----need inside fuse box diagram

If you are looking for the fuse box diagrams or any other diagrams for your Ram, check for a factory service manual for around 20 bucks or so. It's an invaluable tool for my Ram 2500.

Posted on Sep 26, 2009

  • 174 Answers


I have seen once before that the fuse box was bad on a 2003 Dodge 3500. I had power in and nothing out. We had to replace the box. Not cheap! Hope it is simple like a loose connection though. I think I had to pull the inner fender on the drivers side to access the bottom of the fuse box. Pain in the ****, but...

Posted on Oct 01, 2009

  • 3 Answers


there is a pump bolted to the battery box on firewall side it has to come off to get box out

Posted on Apr 25, 2010

  • 3074 Answers

SOURCE: have '99 dodge ram 2500

fuse box on the driver side inside the cab underneath the dash

Posted on Sep 07, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Dodge 2500 transmission

Lost all gears? or when you slowed down you had gears again? Just lower ones. Replace the valve body. If you lose gears and have to wait a while to get them again, rebuild or replace the transmission.

Mar 31, 2014 | 2004 Dodge Ram 2500

1 Answer

04 dodge 2500 diesel surging and dieing

Had the same issue on my 2003 2500. Turned out to be the fuel control actuator on the back of thr cp3 injection pump. Buy from for about $100. dealer wants double that for the exact same Bosch part. Removes with three torx screws after you remove wire connector.

Jul 16, 2012 | 2004 Dodge Ram 2500

1 Answer

I hooked up a trailer to my 04 dodge 2500 (5.7 ltr) and when i plugged in the lights my truck lost all running lights and tail lights. headlights still work and so do turn signals. I checked all the...

your vehicle has a "integrated power module". its a fancy name for a smart fuse box. What likely happened is there is a problem with the trailer wiring. The power module detected the fault and shut down the running lights. The power module will need to be reset at the dealer.

Fuse 15 is a 50 amp fuse for the park lamp relay
Fuse 32 and 34 are 10 amp fuses for the right and left park lights
Fuse 33 is a 10 amp fuse for the trailer park lights.

After it is reset I would not plug in the trailer until the fault is located and repaired.

Oct 12, 2010 | 2004 Dodge Ram

1 Answer

The fuse for the reverse light on the 1995 dodge ram 2500 was burned and somehow damaged the fuse seat. There is still power coming into the fuse connector but when I plug the fuse it burns out...

Something is grounded. Find that first, then address the fuse issue...Easy way to find is to install resetting circuit breaker and use induction amp meter.... activate circuit and follow along the wires with the amp gauge, it will react until you get past the fault...

By fuse seat, I presume that you mean the components that the fuse touches, this area can overheat and melt the plastic. you have 2 options, replace the box or remove that fuse from the box and wire it externally. Label it well.

Sep 12, 2010 | 1995 Dodge Ram 2500

1 Answer

Dodge 2500 ram diesel no tail lights and my abs

replaced the IPM (the fuse box) it was shorted

Oct 25, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

2006 Dodge Ram 2500 diesel truck----need inside fuse box diagram

If you are looking for the fuse box diagrams or any other diagrams for your Ram, check for a factory service manual for around 20 bucks or so. It's an invaluable tool for my Ram 2500.

Sep 19, 2009 | 2001 Dodge Ram 2500 Truck

2 Answers

Problem with hid on 2008 dodge ram 2500

Not too much amperage. HID lights use less amps. Duh. The circuit is showing a failure in the HID kit from not enough amps so it turns off. You need to add a resistor.

Apr 27, 2009 | Dodge Ram Pickup 2500 Cars & Trucks

2 Answers

2003 dodge ram 2500 truck won't start engine lights is on

i had the same problem last year in my 04. unfortunately it turned out it was my pcm. i paid 90 bucks and the dealer uploaded a new program on it and it has ran better than before because dodge has an updated program they loaded. hope this helps

Dec 27, 2008 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77202 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides