Question about 1997 Nissan Pathfinder

1 Answer

How much for new clutch - 1997 Nissan Pathfinder

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 40,701 Answers

Genuine clutch kits cost up to $700.00 After market up to $500.00 depending on the quality Add labour for at least 4 hours at local rate.

Posted on May 04, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I let clutch out when cars in gear the car wont pull away if I turn engine off let it sit fr an hr then drive it its fine fr a while.


For awhile? How long? And then it slips again? I think you need a new clutch, your clutch disc must be worn. A new clutch kit includes a new clutch disc or plate, a new or rebuilt clutch pressure plate, and a new release bearing. Costs about $150-200,for the kit, but you also need the flywheel surface smoothed at a machine shop or garage, then the labor cost of removing the transmission or transaxle to replace the clutch- it all adds up to an expensive job.

Apr 09, 2015 | Cars & Trucks

1 Answer

Truck wont go when I release the clutch.


You need a new clutch. The clutch disc has worn out, now it's slipping on the flywheel. Clutch kit: new pressure plate, new clutch disc, new clutch release bearing, and new crankshaft pilot bushing- about $150-200, somewhere in that range..

Dec 24, 2013 | 1989 Ford Ranger

1 Answer

1983 toyota sr5 pickup wont move when in gear, let off the clutch and it revs up


Your clutch is gone, the clutch disc is worn so much it won't hold.
Buy a clutch kit-includes a new clutch disc, a new or reconditioned clutch pressure plate, and a new clutch release bearing. These three parts will restore your clutch. They all fit together between the transmission and the engine. The transmission has to be removed to put in the new clutch package. The cost of the clutch kit is about $120-$140.

Sep 26, 2013 | Toyota Pickup Cars & Trucks

1 Answer

Replace clutch


A new clutch kit or clutch package has 3 major parts: a new clutch disc (the thin plate with the abrasive surface), a new or reconditioned clutch pressure plate, and a new clutch release bearing (aka, throw-out bearing). Approximately $200 for the package.
Some people have been known to change only the clutch disc (for about $30), and use their old pressure plate and throw-out bearing. Not recommended-same people have been known to have to go back sooner than later to then replace the pressure plate and release bearing. Do it all once, then you won't have to go back and re-do it.

Have you checked the hydraulic clutch operation? Before condemning the clutch disc for failure, make sure the hydraulic clutch cylinder causes the clutch fork or lever to have sufficient travel to engage the clutch when the pedal is depressed. Also check the clutch fluid reservoir for being full.

Sep 18, 2013 | 2006 Kia Spectra

1 Answer

Clutch wont engage after new install


Maybe the clutch master cylinder is not building hydraulic pressure? The internal seals in it may not be holding. Watch the slave cylinder push the clutch lever while someone presses the clutch pedal. If travel is not enough and was bled properly, you may need a new master cylinder.

Jul 07, 2013 | 1991 Chevrolet S-10

1 Answer

I have a new clutch but my truck wont go into gear


You might have somebody press the pedal as you get down and check the clutch travel. Might have an adjustment on the clutch arm.
Could have wrong pressure plate, did you match them. I would check the travel first.

Apr 23, 2013 | 1989 GMC K1500

1 Answer

Clutch will allow me to turn the car on but I am unable the shift gears.


hi,
clutch slave hopefully. check clutch slave fluid, its next to the brake fluid reservoir. it takes brake fluid try bleeding the clutch slave. if it wont bleed then you will need a new clutch slave. If you get the new clutch slave and it still wont actuate correctly then its time for a new clutch. you may be able to shim the clutch slave pin with a small socket untill you get a new clutch but thats not recommended.
jm

Apr 08, 2011 | 1992 Honda Accord

1 Answer

1999 carrera c2 feels like my clutch is slipping.


On the old 911's you could adjust the clutch. The new ones are hydraulic and self adjusting. Sounds like you need a new clutch.

Jan 05, 2010 | 1999 Porsche 911 Carrera

Not finding what you are looking for?
1997 Nissan Pathfinder Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...