Question about 1996 Buick Roadmaster
So the pressure sensor. 5v out gnd...what does the do...
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
- Excess vacuum
- Purge flow during non-commanded conditions
- Fuel Level and Fuel Pressure sensor faults
- EVAP Purge and Vent Valve faults
The ECM monitors the Fuel Tank Pressure sensor in order to determine the level of vacuum/pressure in the EVAP system. The ECM commands both the EVAP Purge Solenoid and the EVAP Vent Valve ON when the conditions are met in order to apply an engine vacuum to the EVAP system. The ECM commands the EVAP Purge Solenoid OFF once the system has reached a predetermined level of vacuum. This test verifies if a vacuum can be achieved in the EVAP system. Failure to develop a vacuum may be caused by a large leak or a restriction.
P0441 1998 Toyota Camry Evaporative Emission Control System Incorrect...
Possible causes - Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
P0441 Toyota Evaporative Emission Control System Incorrect Purge Flow
Jun 01, 2015 | 1998 Toyota Camry
Jan 25, 2014 | 1995 Dodge Dakota
This DTC checks for undesired intake vacuum flow to the EVAP system. The control module seals the EVAP system by commanding the EVAP canister purge solenoid valve OFF and the EVAP canister vent solenoid valve ON. The control module monitors the fuel tank pressure (FTP) sensor to determine if a vacuum is being drawn on the EVAP system
If vacuum in the EVAP system is more than a predetermined value within a predetermined time, this code is set and the MIL (malfunction indicator lamp) is illuminated.
Symptoms of a P0496 DTC will include MIL illumination, and most likely no other noticeable symptoms. Some may experience a hard start / crank condition. In some cases the engine may run rich which may not detected, but can cause damage long-term (think: catalytic converter damage).
Potential causes of a P0496 EVAP code include:
The most common fix for this DTC is to replace the purge solenoid valve. However, be sure to do a proper diagnosis before replacing parts!
Ideally you would use an advanced scan tool, with the ignition on and engine off, you seal the EVAP system using the Seal/Purge function. Then, watch the fuel tank pressure sensor reading when you turn the purge off. If the pressure value is higher than the normal range set by the manufacturer, replace the EVAP canister purge solenoid valve. Refer to a model-specific repair guide for the proper specification.
If you don't have access to the scan tool, you could always disconnect the vacuum line at the purge valve going back to the charcoal canister. Unplug the electrical connector on the purge valve, start the engine, then put your finger on the valve where you disconnected the line. If you can feel vacuum there, the purge solenoid valve is faulty and needs to be replaced. Alternately, you could simply remove the purge solenoid valve and blow into it. It is normally closed, so if air goes through then you need to replace it.
If the purge valve checks out good, either the problem with the valve is intermittent or there is a problem with the fuel tank pressure sensor. To test the fuel tank pressure sensor you will need to have a high end scan tool to monitor the tank pressure with the gas cap removed. If the sensor shows vacuum with the gas cap removed, there is a problem with the fuel tank pressure sensor.
Here is a picture of one purge solenoid valve. Yours may look similar or different, consult a factory service guide or your local vehicle dealership for more details.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.
Thank you for using FixYa, have a nice day.
Aug 22, 2012 | Cars & Trucks
Nov 01, 2011 | 1997 Ford Escort
Jul 24, 2011 | 1996 Mercury Cougar XR7
Jan 14, 2011 | 1998 Nissan Pathfinder
Jan 11, 2011 | 2008 Chevrolet Trailblazer
Dec 14, 2009 | Volkswagen New Jetta Cars & Trucks
Jul 27, 2009 | 1999 Ford Expedition
Mar 13, 2009 | 1997 Mercury Sable
37 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: