Question about Cars & Trucks

Open Question

Torque Settings For Bolts ford sierra 2litre kent engine

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Angle Torque settings head bolts

Use new bolts, tighten in the following stages 1. 20Nm 2. 100Nm 3. wait 3 mins 4. slacken bolts 1&2 retighten to 20Nm +110 degrees 5. carry out stage 4 for bolts 3,4,5 & 6 then bolts 7,8,9 &10 Sequence, 8 4 1 5 9 7 3 2 6 10 Bolts 9 & 10 are flywheel side of the engine.

Posted on Mar 17, 2009

Ad
  • 277 Answers

SOURCE: torque wrench settings for ford focus thermostat

There is a set spec, but for the DIY mechanic,,
Using a !/4 " drive, with the correct long socket, apply a FIRM effort on the wrench, but obviously not too much, as to sheer the studs. Always use a NEW gasket on all mating surfaces.
Regards,DT

Posted on Aug 28, 2009

Testimonial: "a specific torque setting would be better !!"

  • 1 Answer

SOURCE: torque settings for renault megane engine

Does anyone know the torque settings for the following Cam box(bolts), head bolts & crank shaft, the megane scenic is 2001.

Posted on Feb 03, 2010

tburtk
  • 158 Answers

SOURCE: torque on 3.0 ford taurus head bolts

40 ftlbs then 73 ftlbs then recheck at 73 ftlbs

Posted on Feb 06, 2010

wilsodfarm
  • 986 Answers

SOURCE: Torque Specs for Head Bolts on 1997 GMC Sierra V8 5.0 Vortec?

.0L Torque Specs Belhousing to engine bolts 28-38 ft/lbs Camshaft sprocket bolt 40-45 ft/lbs Camshaft thrust plate to engine block bolts 108-144 in/lbs Crankshaft pulley to vibration damper bolts 35-50 ft/lbs Cylinder head bolts -1979-1992 --Step 1 55-65 ft/lbs --Step 2 65-72 ft/lbs -1993-up --Step 1 25-35 ft/lbs --Step 2 45-55 ft/lbs --Step 3 75-85 ft/lbs Differential shaft lock bolt 15-30 ft/lbs Driveshaft U-joint to pinion flange bolts 70-95 ft/lbs Exhaust manifold bolts 26-32 ft/lbs Flywheel mounting bolts 75-85 ft/lbs Front engine mount nuts 72-98 ft/lbs Intake manifold to head bolts --Step 1 96 in/lbs --Step 2 16ft/lbs --Step 3 23-25 ft/lbs Intake manifold (upper intake to lower) 12-18 ft/lbs Oil filter insert to engine block adapter bolt 20-30 ft/lbs Oil pan mounting bolts -1979 --Step 1 (Large bolts) 11-13 ft/lbs --Step 1 (Short bolts) 7-9 ft/lbs --Step 2 (Large Bolts) 15-17 ft/lbs --Step 2 (Short Bolts) 10-12 ft/lbs -1980 to 1987 9-11 ft/lbs -1988 to 1993 6-9 ft/lbs -1994-up 110-144 in/lbs Oil pickup tube to main bearing cap nut 22-32 ft/lbs Oil pickup tube to oil pump bolts -1979 to 1987 10-15 ft/lbs -1988-up 12-18 ft/lbs Oil pump mounting bolts 22-32 ft/lbs Pinion bearing preload 8-14 in/lbs Pressure plate to flywheel bolts 12-24 ft/lbs Rocker arm fulcrm bolts 18-25 ft/lbs Spark plugs 7-14 ft/lbs Timing chain cover bolts 12-18 ft/lbs Vibration damper to crackshaft bolt 110-130 ft/lbs Wheel lug nuts 85-105 ft/lbs

Posted on Mar 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine Torque settings


There are a lot of adjustable torque method, but according to your purpose to distinguish with which kind of appropriate Motor Part Store Motor Parts Wholesale

Jun 26, 2016 | Ford Cars & Trucks

2 Answers

How many ft/lbs of torque is recommended on the flywheel bolts when installing the flywheel on a 1996 GMC Sierra Z-71 4x4 5.7L engine?


GMC Sierra Bolt Torque Specifications. ... The torque converter bolts to the flywheel with 46 foot-lbs. of torque. ... 1996 GMC Sierra Horsepower Torque Specs.

May 02, 2014 | Cars & Trucks

1 Answer

Torque settings for head gasket on LDV convoy 400 2,5ltr ford engine


I can tell you one thing for sure these are torque to yield bolts and they must be replaced, you can't use them over or the head gasket will leak very quickly or the bolt will snap on install..

Jul 13, 2012 | Cars & Trucks

1 Answer

Head bolts torque settings for 1993 ford taurus 3.0 engine


These are the torque valies and sequences for your engine
Torque in 2 steps [1st (33-41 ft-lbs),
2nd (63-73 ft-lbs)]


Torque sequence: (for each bank)
------------
6 4 2 8

5 1 3 7
------------

Good luck and please rate this solutuon

May 21, 2011 | Ford Taurus Cars & Trucks

2 Answers

How to pullout starter on 2000 gmc sierra 4 by 4


4.3L Engine
  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
  1. Install or connect the following:

    Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

    c5acb83.jpg
    Fig. Exploded view of the starter motor-4.3L engines.


  1. Remove or disconnect the following:

    Negative battery cable Bracket and shield Wires Mounting bolts and shims Starter
To install:
Install or connect the following:

Starter Mounting bolts and shim. Torque the bolts to 33 ft lbs. (45 Nm). Wires. Torque battery wire nut to 89 inch lbs. (10 Nm) and ignition nut to 18 inch lbs. (2 Nm). Bracket and shield. Torque the nuts to 53 inch lbs. (6 Nm). Negative battery cable

a557bbc.jpg
Fig. Exploded view of the starter motor-4.3L engines.

Hope help with this (remember rated and comment this).

Mar 17, 2010 | 2000 GMC Sierra

1 Answer

Head bolt torque settings for a 1998 gmc 1500 5.o liter vortex


Cylinder Head Torque
1st - step, all bolts; - 22 ft./lbs. 2nd - step, long bolts; - turn 75 degrees 3rd - step, medium bolts; - turn 65 degrees 4th - step, short bolts; - turn 55 degrees fig121.png

Sep 04, 2009 | 1998 GMC Sierra

1 Answer

Torque settings on a 1999


There are 2 different tranmissions in this vehicle. Make sure you know which one you have when selecting the torque settings. Do notice the 5R55E pan bolts are tightened in inch pounds. 4R70W Torque convert drain plug. 21-22 ftlb Pan bolts 9-11 ftlb 5R55E Pan bolts 115-133 inlb Ford Rear end Pan bolts 33 ftlb

Apr 05, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...