Question about Toyota Hilux
Timing belt diagram
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: toyota hilux 1984 timing
looking at the gears the upper one is on the gear its a dot. it goes flush with the valve cover mating surface to the right. gear on the right lower has a line and it goes pointed up with a mark on the block. crank gear has a v grove and an arrow on the block just under idler adj good luck man mark as fixed thanks
Posted on Sep 20, 2008
I have just replaced my water pump on my 1998 RAVE4, also, the timing belt and the other two belts. I had a tough time with the timing marks. The way you line these marks up is easy if you take the time, First, if you are changing the timing belt you pull the balancer and both top and bottom plastic covers,(do not try to pull top cover off before you take off balencer and the motor mount off or you will just break it.), Second after covers are removed you will have access to the timing belt, you can now remove it by loosening the tensioner bolt and pushing down on the tensioner wheel, the belt then can be taken off. Third take out number one sparkplug and replace the bottom cover by maybe two bolts so that you can see marks on cover, next replace the balancer and bolt. Turn the motor over by hand with the balancer so the small divit on the back of the balancer is on 0 or top dead center on the compression stroke, you can use a compression gauge for this or I just used a mirror and light to shine in the number one cylinder to see the piston. Next remove the balancer and cover and make sure to make a mark on crankshaft gear and housing. Next you will need mirror and flashlight, now turn camshaft gear clockwise to line the hole in the gear with the top timing mark. I recommend a small circle mirror for this. Now replace the belt. I turned the crank shaft gear one tooth counter clockwise off mark and the camshaft one tooth clock wise off mark so when the belt is on you can turn the camshaft gear counter clockwise to get tension on the belt and marks will line up. I would recommend changing water pump,tensioner wheel, and the idler wheel. After belt is on I would replace the bottom cover the balancer and the crankshaft sensor. Iwould then start it to make sure the water pump is not leaking and the motor is not pinging or you will have to tear it back apart again. Good luck and no I am not a certified mechanic just thought this would be helpful from my own experience.
Posted on Apr 30, 2009
malibluert: YOUR IN LUCK! This series engine is simple and the references aren't hard to find. READY???????
IF you are just trying to reset the belt at the top and have not remover the crank pulley, bring the crank around to Top dead center on the # 1 cylinder,. It will read Zero degrees on the timing mark scale.
Up top, look at the cam gear closely You will see that there are 5 spokes which support the actual gear. Look closer and you will see that one of these spokes has a small hole in it about 3/4th of the way towards the outside of the gear. Position the gear to where that hole is at 12:00 PM. NOW, if you look thorough the hole, you should should see a small notch that the hole should be centered on. If not, move the gear until you can look through the hole and the notch falls dead center. At that point in time, you have the crank ant camshaft in perfect time with each other.
When you put the belt on, make sure that the side which is slack is the tensioner side. You should be able to slip the belt on, matching the teeth with the teeth on the gears to where one side is fairly tight and you can not roll the cam counter clockwise.
IF you are replacing the belt, you have the crank pulley off and you position the woodruff key straight up at 12:00 PM and the procedures are all the same other than that. when you set the tension. A good rule of thumb is to find the longest span of belt, and with your thumb and forefinger twist the belt. if it twists to 45 degrees toward the block, it's perfect. Any more or less, needs to be reset.
I hope my answer suffices. A picture wouldn't be any more clear.
Let me know how you did.
NOTE: This engine does NOT bend valves when a timing belt fails.
Posted on May 06, 2009
SOURCE: How to reset timing belt light
to reset the light you need to remove speedo dash assembly ,on the back of the printed curcuit there is a small screw and a hole next to it remove screw and fit to empty hole . refit assembly
Posted on May 07, 2009
SOURCE: timing belt diagram
CLICK on the following LINK. It has the Timing Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com
Posted on Mar 03, 2010
Tips for a great answer:
May 11, 2016 | 2006 Toyota Hilux 3.0
May 05, 2016 | 1996 Toyota Hilux
Mar 25, 2015 | Toyota Cars & Trucks
Jan 06, 2015 | Toyota Cars & Trucks
Jul 26, 2014 | 1996 Toyota Hilux
Jul 17, 2014 | 2006 Toyota Hilux 2.0
Oct 15, 2012 | Toyota Hilux Cars & Trucks
Mar 03, 2010 | 1995 Toyota Pickup
Jan 13, 2009 | 1994 Toyota 4Runner
281 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: