Question about Cars & Trucks

Open Question

Remove & replace side lamp bulb on Chevrolet Tacuma

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

stevenhurc
  • 450 Answers

SOURCE: need to change rear brake bulb on daewoo tacuma

open rear hatch and remove 3 screws down edge of lamp assembly gently pull assembly out and then you can remove globe sockets from lamp assembly to change globe

Posted on Jun 24, 2009

  • 58 Answers

SOURCE: trying to remove driver side headlight assenbly so

open the hood, on the top of the assembly, there should be a bar/rod on each side. simply remove them and the assembly should slide right out

Posted on Jun 20, 2009

  • 1 Answer

SOURCE: replacing a brake light bulb for a 2006 chevrolet equionx

I just replaced the p/s brake light:
1. Pop off the tabs that cover the screws. (flat screwdriver)
2. Unscrew both screws. (philips-head)
3. There is a metal post attached to the light assembly located towards the front of the assembly pointing in towards the center of the car. This post fits into a rubber grommet that is attached to the car. I had to wiggle and rock the assembly to get the post free from the grommet and the assembly off the car, by pulling to the right.
4. Re-assembly requires lining up and inserting the post back into the grommet (use your best Beavis and ******** sound effect now). Put the screws back in and don't forget the covers.

Posted on Sep 15, 2009

  • 142 Answers

SOURCE: How do you replace the passenger DRL on a 2006 Chevrolet Tahoe?

if you remove the headlight, it has two pins that slide down one on each side unhook the wiring for the bulbs. next you will see the top of the parking light on the side closest to the middle the parking lens has a built in clip if u press it in with your finger and pull out the whole lens will be accessible and you will be able to change the burnt bulb

Posted on Sep 28, 2009

TimtheStick
  • 83 Answers

SOURCE: head lamp keeps burning out. replaced head lamp at

You either have a bad ground or the bad electrical connection at the light socket is "simulating" a bad ground. This is putting a high resistance on the bulb and it's taking it's toll by burning out the bulb. I would start with a new socket, and CHECK the ground. If you still have the issue, I would run another complete ground wire and not even worry about checking the ground itself. the Stick

Posted on Dec 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing backup bulbs on 2005 buick rendevous


TAIL LAMP ASSEMBLY AND /OR BACKUP, SIDEMARKER, STOP, TURN SIGNAL BULB REPLACEMENT

REMOVAL PROCEDURE

1. Open the liftgate.
2. Remove the screws from the tail amp.
3. Slide the tail lamp rearward in order to disengage it from the retainers on the rear body panel.
4. Disconnect the electrical connector from the tail lamp wiring harness.
5. Remove the tail lamp and side marker lamp sockets from the tail lamp, depressing the locking tab and turning counterclockwise.
6. Remove the bulbs from the tail lamp and the side marker lamp sockets, if replacing the bulbs.

INSTALLATION PROCEDURE

1. Install the bulbs to the tail lamp and side marker lamp sockets, if removed.
2. Install the tail lamp and side marker lamp sockets to the tail lamp, turning clockwise until the locking tab is fully seated.
3. Connect the tail lamp electrical connector to the wiring harness.
4. Position the tail lamp retainer slots to the tabs on the rear body panel.
5. Install the tail lamp to the rear body panel, pressing into place until fully seated.
6. Install the tail lamp screws to the Taillamp.

NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the tail lamp screws to 2 N.m (18 lb in).

7. Close the liftgate.

Apr 16, 2017 | Buick Cars & Trucks

1 Answer

HOW DO I GET AT TAILLIGHT BULB IN 2008 CHEVY IMPALA TO REPLACE IT?


Ok to remove tail lamp assembly open the trunk and there are plastic nuts that hold the cargo remove that nut and pull back the hard fabric on the sides and there should be 3 to 4 plastic nuts, remove all and remove tail lamp and replace your bulb. good luck!

May 23, 2011 | 2008 Chevrolet Impala

1 Answer

How do I replace the front left (driver side) headlight? I have removed the cap and the electrical, but can't figure out how to remove the bulb so I can put a new one in. Your help is appreciated.


Removal & Installation
  1. Disconnect the negative battery terminal.

  2. Remove the head lamp mounting bolts, then disconnect the lamp connectors.

  3. Replace the head lamp bulb(A), position bulb(B) and turn signal bulbs(C).
    41311_tucs_g0048.gif

    Head lamp bulb(A), position bulb(B) and turn signal bulbs(C)

  4. To install, reverse removal procedure.

Dec 12, 2010 | 2005 Hyundai Tucson

1 Answer

How to change headlight fo 2005 chevrolet uplander


Headlamp Removal & Installation Bulb Replacement To Remove:
  1. Remove the Headlamp Assembly. Headlamp bulbs gm-06-00-3206.gif

  2. Turn the high/low beam bulb socket counterclockwise to remove.
To Install:
  1. Turn the high/low beam bulb socket clockwise to install.
  2. Install the Headlamp Assembly.
Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I gm-06-00-3207.gif

  1. Rotate the headlamp assembly retainer pins and pull up to remove.
  2. Remove the mounting bolts.
  3. Disconnect the harness connectors.
To Install:
  1. Connect the harness connectors.
  2. Position the headlamp assembly on the panel.
  3. Rotate the retainer pins and push down to lock in place.
  4. Install and secure the mounting bolts.
prev.gif next.gif

Oct 07, 2010 | 2005 Chevrolet Uplander

1 Answer

No revers lights


REMOVAL & INSTALLATION 1988–91 R/V Series
  1. Remove the lens-to-housing attaching screws. Remove the lens.
  2. Replace the bulb(s).
  3. Installation is the reverse of removal.
Except 1988–91 R/V Series Fig. 1: Remove the lamp assembly retaining screws 87986p17.jpg
Fig. 2: Pull the lamp assembly from the truck 87986p18.jpg
  1. Lower the tailgate.
  2. Remove the lamp assembly retaining screws.
  3. Pull the lamp assembly from the truck and disconnect the wiring.
  4. Remove the bulb holder fasteners.
  5. Remove the bulb(s) from the lamp.
  6. Install the bulb, connect the wiring and install the lamp. Fig. 3: Disengage the electrical connection 87986p19.jpg
    Fig. 4: Unfasten the bulb holder retainers 87986p20.jpg
    Fig. 5: Remove the bulb holder 87986p21.jpg
    Fig. 6: Pull this type of bulb from the socket 87986p22.jpg
prev.gif next.gif

Sep 03, 2010 | 1994 Chevrolet Suburban

2 Answers

How do I replace a burned out backup light on a 1998 cheverolet silverado c-1500 pickup truck?


Removal & Installation Cab/Chassis gm-06-00-1071.gif

To Remove:
  1. Disconnect lamp assembly electrical connector.
  2. Remove nuts and lamp assembly from bracket.
  3. Remove lens screws.
  4. Remove lens, gasket and bulb.
To Install:
  1. Install lamp assembly and nuts to bracket.
  2. Connect electrical connector.
  3. Install bulb, gasket and lens.
  4. Install lens screws.
Except Cab/Chassis gm-06-00-1075.gif

To Remove:
  1. Lower endgate.
  2. Remove 2 tail/turn signal lamp assembly retaining screws.
  3. Rotate tail/turn signal lamp assembly and remove from vehicle.
  4. Disconnect lamp assembly electrical connector.
  5. Remove bulbs by pulling straight out of bases.
To Install:
  1. Install bulbs by pushing straight into bases.
  2. Connect electrical connector.
  3. Install tail/turn signal lamp assembly to vehicle and secure with 2 screws.
prev.gif next.gif

Jul 17, 2010 | 1998 Chevrolet C1500

1 Answer

How do you replace the headlight bulb located on a 2000 Chevy Tahoe Z-71?


Open hood
On top of core support are 2 metal rods with L shaped ends. Turn the rods out of the plastic holders. Now lift rods out. Take the head lamp out.
Look behind the head lamp.
See an almost round piece with 2 or more wires?
On the side of it is a tab. Push the tab in and turn and remove. Now see the bulb? Okay unplug it & plug in the new one. And reinstall lamp.

May 18, 2010 | 2000 Chevrolet Tahoe

1 Answer

Need to change rear brake bulb on daewoo TACUMA CDX 2004 model but can not get to bulb any ideas please on how to change it


open rear hatch and remove 3 screws down edge of lamp assembly gently pull assembly out and then you can remove globe sockets from lamp assembly to change globe

Jun 24, 2009 | Daewoo Korando Cars & Trucks

1 Answer

NEED TO REPLACE A TAIL LIGHT BULB IN A 2005 CHEVROLET IMPALA


and Repair Notes TAIL LAMP REPLACEMENT REMOVAL PROCEDURE Open the rear compartment. Remove wingnut and pull back the rear compartment trim panel from the tail lamp. Remove the wingnuts from the tail lamp. Remove the tail lamp from the rear body panel. Disconnect the electrical connector from the tail lamp. Remove the tail lamp socket, turning counterclockwise. Remove the bulb from the tail lamp socket. Remove the sidemarker lamp socket, turning counterclockwise. Remove the bulb from the sidemarker lamp socket. INSTALLATION PROCEDURE Install the bulb to the tail lamp socket. Install the bulb to the sidemarker lamp socket. Install the sidemarker lamp socket, turning clockwise. Install the tail lamp socket, turning clockwise. Connect the electrical connector to the tail lamp. Install the tail lamp to the rear body panel. Install the wingnuts to the tail lamp. Pull back the rear compartment trim panel to the tail lamp and install the wingnut. Close the rear compartment.

Jun 08, 2009 | 2005 Chevrolet Impala

3 Answers

REPLACEMENT OF [LOW BEAM] HALOGEN BULB IN 2004 Buick LeSabre


I just Replaced a Low Beam Light bulb on a 2005 Buick La Sabre.

If You use a Metric socket and Remove the Two Silver bolts Attaching the headlight Assemble onto the metal surrounding the the lamp assembly it comes out to the front. This makes it much easier to access the bulb. Twist it counerclockwise & it comes out by pulling gently on the bulb. Then by realeasing a tab that is the socket holder bulb can be removed & replaced with a New #9006 low beam halogen light bulb. Wrap a Paper towel around the bulb & do NOT touch it with your bare hand as this wiil ruin a halogen bulb,

Jan 22, 2009 | 2004 Buick LeSabre

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

315 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...