Question about Toyota Cars & Trucks

Open Question

Gear linkage diagram for toyota hino 13.16

Gears are grating the top ones are grating and not engasging at all and the bottom ones are grating but they engage

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Eaton road ranger gear box linkages sloppy need linkage diagram


this needs professional transmission inside looked at this is not simple cable if gear box sloppy its in the trans

Nov 09, 2013 | 2002 Mitsubishi Mirage

1 Answer

Volvo v70 automatic won't go into gear, and makes a grating noise when you try


Check the shift linkage cable and make sure its in place at the transmission.

Mar 27, 2013 | 1998 Volvo V70

1 Answer

Gear linkages on hiace


Worn gear linkages has to be replaced because of the plastic ends or else you may have losts of shifting problems.

Mar 03, 2012 | Toyota Cars & Trucks

1 Answer

Does a starter come out the top of a 2000 infinity q45??? or the bottom????


bottom, but the manual mentions a couple different procedures. See below.

4.1L Engine
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:

    Negative battery cable Steering gear and linkage assembly Harness connector Starter retainers Starter

To install:
Install or connect the following:

Starter Starter retainers. Tighten the starter retainers to 30-37 ft. lbs. (40-50 Nm). Harness connector Steering gear and linkage assembly Negative battery cable
Alternate procedure:

  1. Remove or disconnect the following:

    Negative battery cable Engine undercover Harness connectors Starter motor mounting bolt and nut
  2. Remove engine mounting insulator bottom nuts, and lift engine approximately 2 inches with a transmission jack
  3. Remove starter motor

To install:
  1. Installation is in reverse order of removal; observe torque values shown in diagram


jturcotte_2457.gif

Fig. Starter motor mounting and torque specifications-Q45 & 2004 M45

Oct 31, 2011 | 1997 Infiniti.5 Q45

3 Answers

88 Toyota Pickup, has become difficult to shift in to gear. Once in gear (1,2,3,or4th) very smooth. I believe must be something up front in the clutch linkage. Possibly? Can get into, but takes awful...


if your linkage was bent it wouldnt shift into all gears easily.sounds like you need to blead your slave cylinder to your clutch.10mm wrench and bleed it like your brakes same type set up.

Nov 24, 2009 | 1988 Toyota Pickup

1 Answer

Where is the shift linage located on an 1985 toyota 4x4 pickup truck? I still cant shift into gear from thje last support you gave me


Without seeing the problem myself, it sounds like you have a clutch problem. It could be the linkage but sounds like the clutch. A manual transmission's linkage is located on the top. It can be reached from the inside of the vehicle through the floorboard. The linkage is attached to the lower end of the gear shift and enters the top side of the transmission. A vehicle repair manual may be helpful, Haynes and Chilton are good ones. Good luck

Oct 16, 2009 | 1985 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...