Question about Cars & Trucks

Open Question

Sofa bed conversion van

I have a 98 conversion van with electric sofa bed, the cables have pull out from the motor that lifts and lowers the bed..

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: How do you lay down rear seat flat?

I just bought a 93 GMC Safari Van and couldn't figure this out either. Luckily, I did have the manual. It appears that the  lever under the front of the sofa moves in forwards and backwards. There is a lever on the corner of each side. Lift up on each and pull cushion forward. Also, you can push on the back of the sofa to help it go down. Hope this helps! 

Posted on Mar 13, 2009

Ad
muntejaya
  • 10421 Answers

SOURCE: sofa will not raise or lower. Thinking switch or

Before you judge switch and electric motor problem, kindly check your Fuse first. Open your fuse box and look defective one. If there is change it at once and test your sofa.

Posted on Nov 26, 2010

SOURCE: 1993 econoline sofa /bed broke...........

This site can get you what you need. http://www.v-sales.com/sofamot.htm

Posted on Mar 26, 2012

  • 747 Answers

SOURCE: how to change top radiator hose on 1997 dodge conversion van with a 5.2 motor

theirn will be a clamp on the radiator side at the top of the radiator remove this clamp follow the rad hose back to the engine side and you'll see another clamp remove this clamp also twist hose from both the radiator and engine side and pull as twisting this will remove the hose then repeat process for installation make sure engine is cold while changing after reinstallation add proper coolant start engine add more coolant as needed

Posted on Sep 01, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to manually let down chevy express 1500 sofa bed


You can't !! Most of the time there is a module under the sofa, that get corroded you have to by pass the module and motor wires, if the motor still working bed would let down other wise motor and module must be replace it

Jun 22, 2014 | Chevrolet Express Cars & Trucks

1 Answer

Sofa bed van


What is the friend

Oct 01, 2013 | 1995 Chevrolet G20

1 Answer

1993 econoline sofa /bed broke...........


This site can get you what you need. http://www.v-sales.com/sofamot.htm

Feb 28, 2012 | Cars & Trucks

1 Answer

Sofa will not raise or lower. Thinking switch or electreic motor.


Before you judge switch and electric motor problem, kindly check your Fuse first. Open your fuse box and look defective one. If there is change it at once and test your sofa.

Nov 26, 2010 | 1993 Ford Econoline

1 Answer

How to remove the heater blower fan on 92 chevy 1500


Heater Core - REMOVAL & INSTALLATION
1991-92 R/V and 1991-98 C/K Series
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the instrument panel glove compartment.
  4. Tag and unplug all electrical leads as necessary.
  5. Remove the center air distribution duct from the floor.
  6. If necessary, remove the ECM and mounting tray.
  7. Remove the hinge pillar trim panels.
  8. Remove the blower motor cover and then remove the motor.
  9. Remove the steering wheel and tilt back the instrument panel slightly.
  10. Remove the coolant overflow tank. Disengage the heater hoses at the core connections.
  11. Unfasten the attaching screws and nut and then remove the heater case.
  12. Remove the seven screws and lift off the heater case cover.
  13. Remove the fasteners and brackets that hold the heater core to the case and lift the core from the case.
To install:
  1. Install the heater core in the case.
  2. Install the heater case bottom plate. Make sure there is a good seal.
  3. Install the heater case into the truck. Tighten the 4 lower screws to 17 inch lbs. (2 Nm); the upper screw to 97 inch lbs. (11 Nm); and the nuts to 25 inch lbs. (2.8 Nm).
  4. Connect the heater hoses at the core tubes.
  5. Install the coolant overflow tank.
  6. Install the instrument panel and the steering wheel.
  7. Install the blower motor and cover.
  8. Install the trim panels and if removed, the ECM. Install the air distribution duct and reconnect all electrical leads.
  9. Install the glove compartment. Fill the cooling system and connect the battery cable.


Blower Motor - REMOVAL & INSTALLATION
1992-98 Models
(see Figure 4)
  1. Disconnect the negative battery cable.
  2. Remove the right rear quarter panel trim.
  3. Disconnect the electrical lead at the fan.
  4. Remove the screws and if equipped, the cooling tube.
  5. If necessary, remove the fan retaining nut and lift out the blower fan.
  6. Remove the blower motor.
To install:
  1. Install the blower motor and then position the fan.
  2. Install the retaining nut and then tighten the mounting screws to 12 inch lbs. (2 Nm).
  3. If removed, install the cooling tube.
  4. Connect the electrical lead. Install the quarter panel trim cover.
  5. Connect the battery cable.
zjlimited_45.jpg

Fig. 4: Auxiliary heating and A/C system





Hope this helps (remember to rate this answer).

Nov 09, 2010 | 1992 Chevrolet C1500

1 Answer

Where is windshield wiper motor for 1992 mercury grand marquis


1992-98 Vehicles
  1. Disconnect the negative battery cable.
  2. Remove the rear hood seal. Remove the wiper arm assemblies by raising the wiper blade off the windshield. Move the slide latch away from the pivot shaft and slowly lower the arm onto the latch. This unlocks the arm from the pivot shaft and holds the blade off the glass. Pull the arm from the pivot shaft.
  3. Remove the cowl vent screws and disconnect the washer hoses from the washer jets.
  4. Detach the electrical connectors from the wiper motor.
  5. Remove the wiper assembly attaching screws, lift the assembly out and disconnect the washer hose.
  6. Unsnap and remove the linkage cover.
  7. Remove the wiper module assembly retaining bolts and remove the module from the vehicle.
  8. Remove the linkage retaining clip from the motor operating arm by lifting the locking tab and pulling the clip away from the pin.
  9. Remove the motor retaining screws and remove the motor from the vehicle.
  10. The installation is the reverse of the removal.

ad37f8d.jpg

Fig.: Lift up to release the clips and remove the hood-to-cowl weather strip


ca6ea0f.jpg

Fig.: Remove the cowl panel-to-firewall retaining clips



Remove the driver's side then the passenger side cowl panel from the vehicle


d57f264.jpg



Fig.: Detach the electrical connector for the wiper motor

Release the wiper motor retaining clips and remove the cover from the vehicle


ffed3a6.jpg



Fig.: Remove the wiper module assembly retaining bolts and remove the module from the vehicle


412221d.jpg



Fig.: Remove the wiper motor retaining bolts and ...


46edc09.jpg


Fig.: ...remove the wiper motor from the vehicle




Hope helps (remember comment and rated this).

Aug 02, 2010 | 1992 Mercury Grand Marquis

1 Answer

Remove the starter motor on a 2001 ford windstar


FIRST TURN OFF RADIO SO YOU WONT LOCK IT OUT.THEN REMOVE NEGATIVE BATTERY CABLE.RAISE AND SUPPORT VAN SAFELY.REMOVE THE HARD SHELL CONNECTOR AT TERMINAL S GRASP THE PLASTIC SHELL.DO NOT PULL ON THE WIRE.DISCONNECT STARTER ELECTRICAL HARNESS.REMOVE THE UPPER STARTER BOLT.SUPPORT THE STARTER AND REMOVE THE LOWER BOLT.REMOVE THE STARTER FROM VAN.THEN WHEN YOU PUT ON NEW STARTER TORQUE BOLTS TO 20 FT LBS.

Feb 21, 2010 | 2001 Ford Windstar

1 Answer

How to replace the Fuel pump on a 2000 Dodge Ram


Iusually pull the bed up if the tank in full.remove the bed bolts spare tire lift bracket where it goes through the bed taillight wiring unplug connector remove screws on the filler pipe and the ground stra.get buddy lift the bed up and move the bed three steps to the rear of the truck.front of bed is now over the rear tire lower bed on tire and you are now over the fuel tank with full access to pump assembly without any problems.

Jan 01, 2010 | 2000 Dodge Ram 1500 Truck

1 Answer

How do you lay down rear seat flat?


I just bought a 93 GMC Safari Van and couldn't figure this out either. Luckily, I did have the manual. It appears that the  lever under the front of the sofa moves in forwards and backwards. There is a lever on the corner of each side. Lift up on each and pull cushion forward. Also, you can push on the back of the sofa to help it go down. Hope this helps! 

Oct 15, 2008 | 1998 GMC Safari

1 Answer

Electric Fuel Pump on an '98 Sierra


when mine went bad I pulled the bed off and moved it back enough toget to the top of the fuel tank it was easier to remove and replace versus dropping the tank tookme and my buddy about 2 hours rig a sling and use a cherry picker to lift bed don't forget to unplug wire harness hope this helps

Jul 16, 2008 | 1998 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

379 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...