Question about 2001 Mitsubishi Galant

1 Answer

What color code is the wires that ignite the ecu

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 563 Answers

AutoZone has repair manuals available online. Should be able to find a pin out for it.

Posted on May 04, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota Camry 1990 V6 2.5L obd1 codes 11 and 14 Check Engine Light on. Codes 11 and 14. Hooked up a good pulled hopefully ECU and check engine light came on again after driving 1/5 of a mile.


code 14 - ignition signal. No IGF signal to ECU 4-5 times in succession.. need check: • Ignition circuit (+B, IGT, IGF) • Igniter • ECU

Jan 03, 2017 | 1990 Toyota Camry

1 Answer

I have a 1990 Pontiac Firebird.My problem is the engine will not turn over. It's not the Battery, ECU, starter,or the wire that is hooked to the starter. What else could it be.


There are 2 wires hooked to the starter. One from the battery and one from the ignition switch. the small (ignition) wire has a fusible link in it. Check voltage on the ignition side of the link(12 volts), then on the starter side. Less than 12 volts. replace the link with the same color.

Aug 13, 2015 | Pontiac Cars & Trucks

1 Answer

Nissan x trail.. Engine wont fire up or runs.. Scan tools had no fault code , try removed the connector of cam sensors and try to start the engine fault code appear on cam sensors fault or no communication...


Sounds like similar problem I had with a 2004 Altima 2.5. Crank but no start. Ended up being a timing chain stretched out and tensioner pinching chain against case not allowing variable timing to work and throwing off cam and crank sensor signals.

Mar 22, 2015 | Nissan XTrail Cars & Trucks

1 Answer

"I have a 2006 Nissan Pathfinder 4.0 V6... Had ECU replaced . Now is throwing a random misfire code P300... what are these code and can one cause the other? Help!"


code p300 refers to random/multiple misfires--misfire detected==causes--spark plugs--HT leads --injectors--ignition coils--low compression--wiring
If you are only now experiencing the problem after changing the ECU, I would suspect that wiring and connections to the new ECU may not have been fitted properly. There may be problems in the ECU CPU (chip) and it may be necessary to use a scanner to reset the CPU program to recognize the sensors of the vehicle correctly

Nov 22, 2014 | 2006 Nissan Pathfinder

1 Answer

Toyota corolla 1997 engine code p1300 ignitor circuit malfunction #1 car starts after 2 minutes will stop


Error Code P1300/ 14. Igniter signal malfunction No.1
Problem Areas:
IGNITION SIGNAL--NO "IGF" SIGNAL TO ECU
--IGNITER/IGNITER CIRCUIT
--IGNITER AND IGNITION COIL/CIRCUIT
--IGNITION AMPLIFIER/ DISTRIBUTOR.
--ECU

Oct 18, 2013 | Toyota Corolla Cars & Trucks

1 Answer

My ECU sockets are broken and i do not know the arrangement of the wires on the ecu since the wires have color code. I took it a to a tech. who fixed it but it keep flashing the ECU


a ecm connector breaking almost never happens i would have a shop or auto parts store read and clear the codes if it pops up again the tech you took it to did something wrong.

Dec 25, 2010 | 2002 Hyundai Santa Fe

1 Answer

Dicribe what fuse to diable the enging to start i need to nowasap


If you are looking for a method of preventing the vehicle from being stolen, a better approach is to cut off the ignition supply to the engine management unit or ECU.. Use a circuit diagram of the ECU wiring to determine the ignition feed or feeds and then use a relay to interrupt those feeds. You can switch the relay using a hidden switch or through a vehicle alarm or anti theft device. Disconnecting the starter can be defeated under the hood by shorting the starter solenoid but cutting the power to the ECU cannot easily be bypassed. One word of warning though, DO NOT cut any wires unless you are 100% certain that the wires you are cutting are the correct ones because you can cause the ECU to set fault codes in its memory which can seriously affect the driveability of the vehicle. If you have any doubts, consult a qualified person..

May 21, 2010 | 2006 Ford Ranger

1 Answer

How do I wire a remote door lock to my 1995 mitsubishi eclipse , what are the wire colors for the power door locks?


Hope this helps. It's for a 2004 eclipse remote start.

12volts white/red (40A) + ignition harness
Starter black/red + ignition harness
Second Starter N/A
Ignition green + ignition harness
Second Ignition N/A
Third Ignition N/A
Accessory blue/red + ignition harness
Second Accessory blue/black + ignition harness
Keysense blue/red ignition harness
Notes: This wire rests at ground, and goes to an open circuit when the key is inserted into the ignition cylinder.
Power Lock purple - pin 33 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Power Unlock lt. green/red - pin 34 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Lock Motor lt. green 5wi pin 19, 28 pin plug below fuses
Unlock Motor green/red 5wi pin 22 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Parking Lights+ green/white + pin 2, 15 pin plug above fuses
Parking Lights- N/A
Hazards green - pin 55 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Turn Signal(L) green/blue + pin 8, 15 pin plug above fuses
Turn Signal(R) green/yellow + pin 13, 15 pin plug above fuses
Reverse Light red/blue + pin 9, 43 pin plug in driver kick
Door Trigger see notes - see notes
Notes: The driver door trigger is lt. green, pin 6, in a 15 pin plug above the fuses. The passenger door is lt. green/black in pin 65 at the ETACS ECU. Use both wires and diode isolate each.

The ETACS ECU is attached to the back of the fuse box.
Dome Supervision green/orange - pin 1, 3 pin plug above fuses
Trunk/Hatch Pin red - pin 62 or 37 at ETACS ECU
Notes: It is in pin 62 on the coupes, and in pin 37 on the convertible spyders.

The ETACS ECU is attached to the back of the fuse box.
Hood Pin green/red - pin 24 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Trunk/Hatch Release green/white 5wi pin 32 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Power Sliding Door N/A
Factory Alarm Arm lt. green/black - pin 42 at ETACS ECU
Notes: Meter this wire while turning the key in the driver door key cylinder.

The ETACS ECU is attached to the back of the fuse box.
Factory Alarm Disarm orange - pin 25 at ETACS ECU
Notes: Meter this wire while turning the key in the driver door key cylinder.

The ETACS ECU is attached to the back of the fuse box.
Disarm No Unlock blue/red - pin 27 at ETACS ECU
Notes: Meter this wire while turning the key in the hatch/trunk key cylinder.

The ETACS ECU is attached to the back of the fuse box.
Tachometer white or black/white ac engine speed detection connector
Notes: The engine speed detection connector is a single pin connector in the fuse/relay box under the hood.

Can also go to one of the ignition coils or the distributor assembly and use the black/blue or white/green wire.
Wait to start N/A
Brake Wire green/orange + brake pedal switch
Parking Brake yellow/green - parking brake switch
Horn Trigger lt. green/black - pin 44 at ETACS ECU
Notes: The ETACS ECU is attached to the back of the fuse box.
Memory Seat 1 N/A
Memory Seat 2 N/A
Memory Seat 3 N/A
Interface Module: Category:
Immobilizer Bypass Required:
Yes Type:
Transponder
Part #: 556UW
Alternate Part1 #: DesignTech 20402
Alternate Part2 #: DesignTech 29402
Notes: Standard on all models.

Good luck.

Mar 02, 2010 | 1995 Mitsubishi Eclipse

1 Answer

I have a 1994 Toyota 4Runner with a V6 and the check engine light came on i jumped the terminals and code 14 and 26 came up. what does the codes mean?


These are the codes and possible causes taken from http://www.off-road.com/toyota/tech/codes/
Code 14 :
IGNITION SIGNAL--NO "IGF" SIGNAL TO ECU
--IGNITER/IGNITER CIRCUIT
--IGNITER AND IGNITION COIL/CIRCUIT
--ECU

Code 26 :
AIR/FUEL RATIO RICH INDICATOR
--INJECTOR FAULT(S)
--FUEL PRESSURE
--OXYGEN SENSOR
--AIRFLOW METER OR MAP SENSOR
--IGNITION
--ECU
--COLD START INJECTOR

Sep 17, 2009 | 1994 Toyota 4Runner

1 Answer

How check distrributor ?


1993 dodge stealth ,obd2 connector will like to know what color wire to obd2 connector should have power when ignition is turn on and where that color wire goes to

Aug 18, 2008 | 1993 Dodge Stealth

Not finding what you are looking for?
2001 Mitsubishi Galant Logo

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...