Question about Cars & Trucks

Open Question

My hazard warning lights come on for no apparent reason when I leave the car

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: hazar warning light is blinking after changing battery

hi there do you know if there is an alarm fitted to this car and if so do you have the remote. if not you may have to get the alarm removed or put back into valet mode as this would have been how the alarm would have been set until the battery went flat and has now gone back to the default setting of the alarm.

Posted on Oct 30, 2008

  • 101 Answers

SOURCE: air bag waring light came on for no apparent reason

Possible trouble areas are drivers side air bag, spiral cable in column, wiring to the air bag sensor assembly or the sensor assembly its self. Without a competent technician using the proper diag tools it would hard to pin point the problem.

Posted on Apr 19, 2009

johnjohn2
  • 5763 Answers

SOURCE: hazard warning lights won't stop flashing

this sounds like the alarm system is going off,try unlocking from the pass/side door and if lights dont flash then you have a bad lock switch in the door.

Posted on Jun 18, 2010

ZJLimited
  • 17970 Answers

SOURCE: hazard warning light don't work

Its possibe that ypou have independient FLASHER device, one for hazard and one for turn signal; check backside of fuse panel and replace it.

Posted on Aug 28, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emergency flasher switch


The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

Nov 26, 2015 | 2010 Chrysler Town and Country

1 Answer

Battery warning light is coming on for no apparent reason. I just replaced the oil pressure sending unit and then reconnected the neg cable and now warning light stays on.


Try removing either battery cable for about 15 mins. that should reset the computer in car and make battery light go off, if that dont work check battery cables to make sure they are tight. Billy Wyatt

Sep 07, 2013 | 1996 Chevrolet Cavalier

1 Answer

Engine warning lights comes on


Your not correct,there is a reason

Any dash light that stays on or comes
on after the motor is started, is an indication
you have a problem

No check light or warning light will go out until
you diagnose the reason it is on & correct the
problem

Jan 29, 2013 | 1999 Nissan Primera

1 Answer

I have a 1996 Saab 900 when I start the car and turn on the head lights the dash lights will turn on and then go out. Along with the dash lights, the radio lights and the lights along the shifter...


It could be a bad connection or a bad headlight switch, but there is also a safety switch on the car that turns the dash lights out when you lose your tail lights, so before you go any further check if your tail lights are working, your car may just be telling you about another problem.

Jan 26, 2011 | 1996 Saab 900

3 Answers

No break lights or hazard lights or no turn signals


first check all fuses then under hood check all fusible links

Aug 12, 2009 | 2000 Pontiac Grand Am GT

1 Answer

The turn on lights does not flash


Check out this recall below:
Bulletin No.: 04098A

SPECIAL POLICY
Subject:
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers 

Condition
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.

Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.

Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE 
REMOVAL PROCEDURE 

Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent. 
Remove the instrument panel cluster. 
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector. 
Disconnect the electrical connectors from the hazard warning switch. 
Remove the hazard warning switch from instrument panel. 

INSTALLATION PROCEDURE
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) . 
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster. 
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.

May 24, 2009 | 2000 Oldsmobile Alero

1 Answer

Air bag waring light came on for no apparent reason


Possible trouble areas are drivers side air bag, spiral cable in column, wiring to the air bag sensor assembly or the sensor assembly its self. Without a competent technician using the proper diag tools it would hard to pin point the problem.

Mar 28, 2009 | 2003 Toyota Corolla

1 Answer

Hazar warning light is blinking after changing battery


hi there do you know if there is an alarm fitted to this car and if so do you have the remote. if not you may have to get the alarm removed or put back into valet mode as this would have been how the alarm would have been set until the battery went flat and has now gone back to the default setting of the alarm.

Sep 20, 2008 | 1995 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...