Question about Kia Sedona

Open Question

Fuel tank pressure sensor diagram - Sedona Kia Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75807 Answers

SOURCE: I have a code p0452 low fuel tank pressure. Is the

yes the pressure sensor in mounted in a rubber grommet on the top of the fuel tank. it could be the sensor but the only way to know for sure is have the dealer do a evaporative emissions fuel tank pressure test, they have the special tools to do this, outside shops do not. Have u tried a new gas cap, they can leak and cause the problem, in fact that is very common.

Posted on Mar 07, 2009

  • 1 Answer

SOURCE: location Fuel Tank Pressure Sensor on a 2005 chevy express van

lOOK UNDER THE REAR OF THE VEHICLE ABOVE THE SPARE TIRE ON A CROSSMEMBER BETWEEN THE FRAME RAILS.

Posted on Apr 24, 2009

  • 462 Answers

SOURCE: I would like to know were the fuel tank pressure sensor

The sensor is located on top of the fuel pump. It should be black in color. You have an access plate in the trunk to get to the fuel pump without dropping the tank.

Posted on Aug 21, 2009

  • 30 Answers

SOURCE: possible vaccum in fuel tank, EVAP system.

TRY REPLACING THE EVAP CANISTER

Posted on Oct 27, 2009

  • 280 Answers

SOURCE: replace crank sensor still same code check fuel

If you do not get the code erased it will come back

Posted on Mar 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fuel control module 2008 escalade and the fuel pump quit working.if I run a hot wire to it it will run but as soon as I remove the hot wire it quits


Ran a hot wire to what fuel pump or the control module ? Which of these is yours ?
Figure 9: Fuel Controls - Fuel Pump Controls (LY6)
Figure 10: Fuel Pump Flow Control Module (Except LY6) Does yours have fuel pump flow control module under the vehicle Fuel Pump Flow Control Module (except LY6)
Mounted to the left side of the frame assembly below the driver seat ?
Fuel Pump Flow Control Module (FPCM) - LMF
The fuel pump flow control module (FPCM) is a serviceable GMLAN module. The FPCM receives the desired fuel pressure message from the engine control module (ECM) and controls the fuel pump located within the fuel tank to achieve the desired fuel pressure. The FPCM sends a 25 KHZ PWM signal to the fuel pump, and pump speed is changed by varying the duty cycle of this signal. Maximum current supplied to the fuel pump is 15 amps. A liquid fuel pressure sensor provides fuel pressure feedback to the FPCM.
Electronic Returnless Fuel System (ERFS) - LMF
The electronic returnless fuel system is a microprocessor controlled fuel delivery system which transports fuel from the tank to the fuel rails. It functions as an electronic replacement for a traditional, mechanical fuel pressure regulator. A pressure vent valve within the fuel tank provides an added measure of fuel pump flow control module (FPCM). Desired fuel pressure is commanded by the engine control module (ECM), and transmitted to the FPCM via a GMLAN serial data message. A liquid fuel pressure sensor provides the feedback the FPCM requires for Closed Loop fuel pressure control.
If your vehicle has this system check it for DTC'S - diagnostic trouble codes . Will take guess work out of it .
DTC P0191: Fuel Rail Pressure (FRP) Sensor Performance
DTC P0192: Fuel Rail Pressure (FRP) Sensor Circuit Low Voltage
DTC P0193: Fuel Rail Pressure (FRP) Sensor Circuit High Voltage
DTC P0230: Fuel Pump Relay Control Circuit
DTC P0231: Fuel Pump Control Circuit Low Voltage
DTC P0232: Fuel Pump Control Circuit High Voltage
DTC P023F: Fuel Pump Control Circuit
The engine control module (ECM) supplies voltage to the fuel pump flow control module (FPCM) when the ECM detects that the ignition is on. The voltage from the ECM to the FPCM remains active for 2 seconds, unless the engine is in crank or run. While this voltage is being received, the FPCM supplies a varying voltage to the fuel tank pump module in order to maintain the desired fuel rail pressure.
DTC P025A: Fuel Pump Control Module Enable Circuit .
Ford Electronic Returnless Fuel System Diagnosis Part 1 this for ford but the GM system works the same . You'll need a wiring diagram so you know what wires are what . Free wiring diagrams http://www.bbbind.com/free_tsb.html

Oct 31, 2016 | Cars & Trucks

1 Answer

Replacing a fuel tank pressure sensor. Is this different than the fuel regulator on the fuel pump?


Fuel tank pressure sensor is a sensor that is on my vehicle and I would assume on all vehicles on the fuel tank itself. Fuel tanks build up pressure (lots of pressure sometimes) They must have a way to vent this pressure so manufactures install fuel tank pressure valves and wire a sensor to it and hook it up to the on board computer. On my Mercury marquis it is impossible to replace my sensor without first removing the fuel tank. So to answer your ? yes the fuel pump regulator is different than the fuel tank pressure sensor. If you need help positively locating where it is go to Autozone.com and create an account (free) and enter your yr/mk/model and there you can go to repair help and view online Chiltons repair manuals. Good Luck!

Nov 03, 2015 | Cars & Trucks

1 Answer

Where is fuel pressure sensor at cant find it


Tank pressure sensor? Tank pressure sensor is in the fuel pump it on tank, it shouldn't have a fuel pressure sensor, it will have a fuel pressure regulator on the return line off the fuel rail

Sep 29, 2014 | Cars & Trucks

1 Answer

Diagram Suzuki Swift Fuel Tank Pressure Sensor


what is your cars problem and maybe we can help ??

Aug 18, 2012 | 2000 Suzuki Swift

2 Answers

Where located fuel sensor Suzuki Ario 2003


Component location diagrams for most 2003 Suzuki Aerio cars and light trucks sold in the U.S. from 1990+.
clsk2003aeri003.gifIgnition System Components Location Diagram for 2003 Suzuki Aerio 2.0 L4 GAS
Components on diagram:
  • TP Sensor
  • Ignition Coil
  • ECM
  • MAF Sensor
  • CMP Sensor
  • clsk2003aeri007.gifElectronic Shift Control System Components Location Diagram for 2003 Suzuki Aerio 2.0 L4 GAS
    Components on diagram:
  • Data Link Connector
  • Transmission Range Sensor
  • Throttle Position Sensor
  • Pressure Control Solenoid Valve
  • Battery
  • clsk2003aeri010.gifInstrument Panel For Connector Layout Diagram Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • Clutch Switch
  • Thermistor
  • Brake Light Switch
  • Blower Motor Relay
  • Heater Fan Motor
  • clsk2003aeri011.gifInstrument Panel Harness Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • Wiper Switch
  • Washer Switch
  • Data Link Connector
  • Turn Signal Relay
  • Radio
  • clsk2003aeri015.gifHeadlight System Location Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • Headlight Relay
  • Headlight
  • Clearance Light
  • Headlight Diode
  • Clearance Light Relay
  • clsk2003aeri022.gifFuel System Components Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • Fuel Pump Relay
  • Fuel Tank Pressure Sensor
  • EVAP Canister
  • Fuel Tank Pressure Control Valve
  • Fuel Filler Cap
  • clsk2003aeri027.gifFloor For Single Unit Parts Diagram for 2003 Suzuki Aerio 2.0 L4 GAS
    Components on diagram:
  • Wheel Speed Sensor
  • ABS Control Module
  • G Sensor
  • Air Bag Control Module
  • EVAP Canister Vent Valve
  • clsk2003aeri030.gifInstrument Panel For Ground Point Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • Instrument Panel Ground Points
  • clsk2003aeri036.gifEngine Compartment For Single Unit Parts Diagram for 2003 Suzuki Aerio 2.0 L4 GAS
    Components on diagram:
  • Throttle Position Sensor
  • Horn Relay
  • Radiator Fan Control Relay
  • Cruise Control Module
  • Condenser Fan Relay
  • clsk2003aeri037.gifEngine Compartment Components Diagram for 2003 Suzuki Aerio SX 2.0 L4 GAS
    Components on diagram:
  • MAP Sensor
  • Knock Sensor
  • Noise Suppressor
  • Heated Oxygen Sensor
  • Sep 18, 2011 | 2003 Suzuki Aerio

    1 Answer

    Where is the fuel tank pressure sensor located in a 1998 Buick Regal Supercharged?


    Hi,

    I believe that I can help you.

    Go to your throttle body.
    • A large diameter fuel rail is attached to the top of the intake manifold and supplies fuel to all of the injectors.
    • A fuel pressure cap is located on the rail for quick pressure checks,
    • The electric fuel pump is attached to the fuel sender assembly in the fuel tank. It pumps fuel constantly from the tank, through the fuel rail on to the engine and back to the tank.
    • The fuel pressure regulator that is mounted on the fuel rail maintains pressure across the injectors under all operating conditions.
    Unfortunately, my scanner is inoperative and I cannot provide you with a diagram

    May 18, 2011 | 1998 Buick Regal

    1 Answer

    What is the codes means po452 and po453


    Hi,

    The codes indicate a problem with the fuel tank pressure sensor. One code is for no volts, the other is for high volts. Without a scanner hooked up to monitor. I have to go with you have a bad fuel tank pressure sensor. this is an emissions control sensor. the tank is pressurized and the sensor monitors it for leaks etc. the tank must come out as it is mounted on top of fuel pump module

    REMOVAL PROCEDURE

    1. Raise the vehicle.
    2. Remove the fuel tank. Refer to Fuel Tank .
    3. Remove the fuel tank vapor pressure sensor electrical connector.
    4. Remove the fuel tank pressure sensor.
    INSTALLATION PROCEDURE
    1. Install the fuel tank vapor pressure sensor.
    2. Install the fuel tank vapor pressure sensor electrical connector.
    3. Install the fuel tank. Refer to Fuel Tank .
    4. Lower the vehicle.
    Thanks.

    Feb 02, 2011 | 2001 Chevrolet Blazer

    1 Answer

    Where is the gas pressure sensor on an 03 1500 5.3 Liter silverado located..any diagrams would be great


    The fuel tank pressure sensor attached to the top of the fuel pump module on top of the gas tank.

    Its the black pert on the top of the pump on the right side.

    44b6ef7.jpg

    Oct 29, 2010 | 2003 Chevrolet Silverado 1500

    2 Answers

    Whats the best way to replace fuel pump ? drop the tank or the bed


    According to the factory service manual, you should drop the tank, there are pictures and diagrams with these in the manual.
    1. Disconnect the negative battery cable.
    2. Relieve the fuel system pressure.
    3. Drain the fuel tank. .
    4. Remove the fuel tank.
    5. Remove the fuel sender assembly.
    6. Note the position of the fuel strainer (2) on the fuel sender.
    7. Support the fuel sender assembly with one hand and grasp the strainer (2) with the other hand.
    8. Pull the strainer off the fuel sender. Discard the strainer after inspection.
    9. Inspect the strainer. Replace a contaminated strainer and clean the fuel tank.
    10. Disconnect the fuel pump electrical connector (5).
    11. Remove the electrical connector retaining clip (6) from the fuel level sensor.
    12. Disconnect the sensor electrical connector (7) from under the fuel sender cover.
    13. Remove the fuel level sensor retaining clip (4).
    14. Squeeze the locking tangs and remove the fuel level sensor (3).
    15. Remove the fuel pressure sensor (1).
    A good place to get an inexpensive service manual is from Promanuals it's a complete factory manual.

    Sep 26, 2009 | 2000 GMC Sierra

    1 Answer

    PO452 code!


    Try this sight and follow the directions. http://www.myjdmphoenix.com/images/04_xB_Repair_Manual/05%20-%20Diagnostics/SFI%20system/evaporative%20emission%20control%20pressure.pdf

    Random misfire could mean you need a tune up. If you are at 100000 miles put in good X.C platinum plugs and a/c Delco wires.. Do a good fuel injection cleaning.

    Hope this helps.
    Rich

    Aug 20, 2009 | 2001 Chevrolet Blazer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Kia Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Kia Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...