Question about 2002 Hyundai Elantra GT

Open Question

Hyundai Elantra 2002 cylinder head removal - 2002 Hyundai Elantra GT

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2002 hyundai elantra

no timing to set

Posted on Aug 23, 2008

Ad
ghost4548
  • 776 Answers

SOURCE: i have a 1997 hyundai elantra 1.8 i need torque specs. for head

go to http://www.hmaservice.com/ and register. After that, you'll have access to manuals, service bulletins, wiring diagrams, etc.

Posted on May 28, 2009

  • 1071 Answers

SOURCE: Please provide torque settings for the head bolts

1st stage 45lbs then 65 then 85

Posted on Aug 21, 2009

  • 181 Answers

SOURCE: Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS

You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Posted on Feb 19, 2010

  • 171 Answers

SOURCE: how to replace 2002 hyundai elantra hub and bearing

With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Posted on Apr 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace left front fender


Replace left front fender - Fixya

www.fixya.com/cars/t26028082-replace_left_front_fender
Dec 29, 2015 - replace left front fender - Hyundai Motor 2003 Elantra question. ...Question about Hyundai Motor 2003 Elantra. Open Question ... How do i remove left front fender clip on a Lincoln ls 2002? Jan 04, 2015 ' 2002 Lincoln LS.

Replace 2003 hyundai elantra front passenger outside door ...

www.fixya.com/cars/t17348691-replace_2003_hyundai_elantra_front
Mar 26, 2013 - Question about Hyundai Motor 2003 Elantra. Open Question.Replace 2003 hyundai elantra front passenger outside door handle. Need to replacebroken exterior door handle on front passenger .... replace left front fender.

Dec 29, 2015 | Hyundai Motor 2003 Elantra

Tip

Stalling and running rough - Hyundai Elantra - 2001-05


The Hyundai Elantra 2001 - 2005, 2.0 L engine is noted for this problem. It will lack power on acceleration and run rough and stall while driving. The engine light will come on for misfire codes. This problem is caused by a vaccum leak at the intake manifold gasket. The gasket is broken and needs to be replaced.
To replace the intake gasket with a new one, remove the 12m nuts holding the intake to the cylinder head. Then pry back( note: you do not have to completely remove the intake manifold here) the intake manifold to gain excess to remove the old gasket. Remove any excess gasket and clean with brake cleans the surface area of the intake. Install the new intake gasket on to the head and carefully install intake on to cylinder head studs. Tighten up nuts gradually and evenly to 15-20 ft.lbs.

Steve

on Jan 14, 2010 | Hyundai Elantra Cars & Trucks

1 Answer

Does a 2002 hyundai elantra has fuel injectors ?


Yes it does. A fuel injector is a device that atomizes and then delivers the fuel into the cylinder just before the piston squeezes the fuel and air mixture and the spark from the spark plug fires. Ergo your 2000 Hyundai Elantra being a 4 cylinder vehicle, has 4 fuel injectors.

Jun 22, 2014 | 2000 Hyundai Elantra

1 Answer

Need to intall new front exterior drivers side door handle on a 2002 Hyundai Elantra GLS


remove the interior door trim and you will see small nuts holding the handle onto the outer door skin. Remove any rods /clips and undo the nuts and the handle will come out.

Mar 18, 2014 | Hyundai Motor 2002 Elantra

2 Answers

Hyundai elantra head gasket keep blowing


thats got a cracked head get a preasure test done on head

Aug 06, 2013 | Cars & Trucks

2 Answers

Where is thermostat for radiator on 2003 Hyundai elantra


Its is located exactly where the lower radiator hose connects to the engine.To remove the thermostat we have to remove the air filter housing . The thermostat is held in position by means of two bolts.

Dec 13, 2010 | 2004 Hyundai Elantra

1 Answer

1996 hyundai lantra cylinder head torque spec


dak408_40.gif
Revised Bulletin
This TSB supersedes the Cylinder Head Bolt Torque Specifications previously described in TSB # 96-20-003, TSB # 96-20-003-1 and TSB # 97-20-004.
DESCRIPTION:
This bulletin provides torque specification corrections to the 1996 and 1997 Elantra Shop Manual, 1997 Elantra Service Data Book, 1997 Tiburon Shop Manual and 1997 Tiburon Service Data Book.
Please record the corrections (listed) in the appropriate manuals and write the TSB number on the bottom of the pages listed below for future reference.
CYLINDER HEAD BOLT:
(M10) 30 Nm (300 kg.cm; 22 lb.ft) + (60°to 65°) + (60°to 65°)
(M12) 35 Nm (350 kg.cm; 26 lb.ft) + (60°to 65°) + (60°to 65°)

Nov 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Correct torque on cylinder head bolts for Hyundai Elantra 1.8GLS


You have two bolt sizes the shorter or smaller of the two sizes is called M10 the torque is 22ft lbs +65 degrees +65 degrees again The larger of the two bolts is called a M12 the torque for these are 26ft lbs +65+65. There is a tightening order staring at the top center bolt and working in a circle They have to be torqued in three steps. If you dont under stand something about this repost and I can help you farther. If this is helpful please mark that it was I do this for free to help people DRIVE SAFE TIM

Feb 19, 2010 | 1997 Hyundai Elantra

1 Answer

2002 Hyundai Elantra. Right marker light bulb is out.


Two retainers hold wheel well liner at the bumper - remove them then bend liner back to access marker lamp assy & socket.

Oct 12, 2009 | Hyundai Motor 2002 Elantra

3 Answers

Hyundai elantra 2002 over heated stopped running and cannot start up


The head gasket is probably bad. unplug the coil pack and remove the spark plugs and turn key to start, if its leaking coolant will shoot out of spark plug holes, seen it a lot.

Apr 27, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
2002 Hyundai Elantra GT Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...