Question about Cars & Trucks

Open Question

Nante mini digger

Boom will not lift up but all other hydraulics are working

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
Molson02536
  • 3854 Answers

SOURCE: hydraulic lifts on back door quit working

Sorry you can not repair the hydraulic life, your going to have to replace it. You can buy new ones at the Auto Zone or Parts Source and both parts store can give you the how to do the job your self.
It's only going to take you less then 5 min to change one side at a time with the use of a flat head screw driver.
Good luck and hope this helps, most of the time the parts person can help you change the back door lift.

Posted on May 05, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Takeuchi mini digger tracking problem


Pressure valve? does it only do it to only one side? Left or right. The reason you move both tracks with the bucket running is because you relieve pressure. One side is free wheeling, As they call it. I work on cars, But also have done to many hydraulic components. You have a pressure control valve that is bad.

Jul 10, 2016 | Mini Cars & Trucks

1 Answer

What is the correct relay solenoid for an electric motor that runs the hydraulic pump for a Telsta A-28D aerial boom lift ?


TELSTA A28D Bucket Controls Acting Up - Contractor Talk

www.contractortalk.com > Forum > Equipment & Safety > Vehicles
Sep 5, 2009 - 20 posts - ‎9 authors Problem I'm having with my truck is that the controls on the boom are acting .... I'd also like to replace the 3 small relays in the main control panel where the boom ... We recently purchased a 2000 e350 with the Telsta A28D lift and had .... back to the tower and up to the controls back down to the solenoids.

Jul 25, 2015 | Cars & Trucks

2 Answers

Hydraulics on a hanix 1.5 ton mini digger not working, what can i try?


If fluid is ok look at safety lever switch electric button or whatever activates the switch, thats your start

Jan 03, 2015 | Mini Cars & Trucks

1 Answer

Replace cylinder in bottom boom on hiranger bucket truck


ive heard of folks doing it without a crane but i would not try it , alignment is too critical with getting guides and stops back in and with nothing to move boom that would be too difficult

anyways: suspend boom end with double straps from crane , disconnect hydraulic/electric swivels/plugs at truck end lift end of boom slightly with boom all the way extended straight out , remove acess panel (both sides) at jct of upper/lower boom section . remove C clip one side drive out pin oppisite side (wiggle boom to clear pin) locate stops in lower section boom end unbolt , slowly pull upper boom with crane away take care of hydraulic lines and electric wires set on floor on wood cribbing , locate bottom of cylinder truck end find C clip and pin Might be behind a trim cover that might need to be remove drive out pin also remove bottom cylinder hyd hose connect crane to cylinder end move out a foot or so remove top cyliinder hydraulic hose then carefully slide out cylinider with crane , Note if your valves are not tight and new oil will leak back and cause boom base to sag when you unhook hydraulic hoses , your gonna need to block this up with wood cribbing just in case

reverse removal process to install new one , also i would not just install a new seal (you can) with out having cylinder recromed I'll bet it's rusty thats what tears the seals up
and allways replace entire oil volume in hydraulics your old seal is in old oil not good for the new one

Apr 26, 2014 | 1985 Chevrolet Chevy

1 Answer

I have an old UHO 83 digger. The problem is that when I walk the digger it moves about a metro and stops, when i release the lever and push it forward it will move again and then stop again until the lever...


i used to know some one that had a hitachi. was always having problems with it not moving. if i remember right it was the brake leaking think its air system and it was just leak. he had it fixed and added an air line indicator fitted think the boom works on the same system. if i remember right there is a foot brake and a lock brake lock brakes hydraulic . and the normal braking. but in the event of the air brake falling the hydraulic brakes take over. but this is from memory and it was a long time ago you dont see meany round here any mor they all jcb's and other makes.

Mar 24, 2014 | Cars & Trucks

1 Answer

My excavator hitachi ex200-1 weak swing and when you swing then stop vibration begin on turn table when i stop to swing,and when i swing and lift cylinder raise,vibration on the turn table will contin


Not sure would need to have a good look ,but i suspect a safety valve isnt closing properly causing thumping within the hydraulic system which is the vibration you can feel,shouldnt cost a lot to repair providing the faulty valve can be located so return to the dealer as they will have a good idea as yours isnt the first to go wrong iam sure

Sep 24, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...