Question about Cars & Trucks
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
The Normal Temperature Range to the Fan Start is: A/C ON 181 F.
A/C OFF 199 F. When the Engine Reach this Temperature the Fan should start.
OK. Do this simple test.
1---- Start the engine, Desconnect the ECT Switch located on the Radiator,
See if the Fan come ON. If yes, if not go to step #2
Connect the ECT SWITCH and leave the car Running and with a Temperature gage.
See the temperature, if the Temperature go more than 199 F.
Turn the Engine OFF.
Disconnect the ECT sensor and check for Ground at the WHITE/BLACK wire.
If ground exist, Replace the ECT switch.
But if not. Check the wire for any damaged, and the ground at the Front Left Fender.
Repair as need.
2---- check the Fuse link RDI FAN . 30 amp.
Check the Fuse link CDS FAN 30 amp.
Replace if need.
And Return to step # 1.
Check the Radiator fan Relay, Rad fan relay 2 and 3. Replace if need.
Ok. I hope this help on your question.
I can give to you the WIRING DIAGRAM of the Fans, But I need a E-MAIL adress to do that.
Thank you for use fixya....
Posted on Sep 25, 2008
SOURCE: 2004 Toyota Camry Brakes
Raise the vehicle up and remove the rims & tires
Remove the brake pads, and then remove the calipers from the caliper retention brackets, do NOT remove the brake hoses from the calipers.
Remove the caliper retaining brackets from the hub assemblies (2 large bolts on backside of the bracket)
Tap the brake rotors off of the hubs, hit them from the back side of the rotor.
No big mysteries here, this is a very easy job.
Posted on Oct 21, 2008
SOURCE: Stalling Toyota Camry 2004
P-0102 and P-0113 are mass air flow and intake air temp codes, the P-0136 is an Oxygen sensor code. Before you do anything, check for debris in the Mass Air Flow Sensor, it's small black box with electrical wiring connector that is screwed into the intake air tube, between the air box and the intake manifold. Undo the screws, remove the sensor, and, with a flashlight, and look down inside it for debeis, or broken wires inside it. If it's dirty, it could throw a P-0136...Comment back on what you find; hope this helps, and thanks for choosing FixYa!
Posted on Oct 24, 2008
there are actually 3 temp sensors. 1 is on the top of the engine that goes to temp gauge in dash has 1 wire. next to it is a 3 wire sensor for engine control and choke. on the bottom of the radiator next to the hose is a 2 wire sensor. loosen all 3 but leave connected. get engine hot past halfway point on dash gauge. with ac off disconnect 1 sensor at time. start with 2 wire under radiator. it takes the most abuse. fan will come on when you disconnect broken sensor. 2sensor must agree for fan to stay on till engine cools when turned off. note this is solution i used after verifying fuses, fuseable links and relays worked.WOO HOO! make sure you check both the fuse box under hood and fuse boxleft side of steering wheel my ECU fuse was inside my bros was outside.ECU B on my car goes to nothing and is under hood. Had it confused with ECU on wiring diagram.DOH!
Posted on Apr 03, 2009
Tips for a great answer:
Nov 23, 2012 | 2004 Toyota Camry
Oct 03, 2012 | 2000 Toyota Camry
Jul 19, 2012 | 1991 Toyota Camry
Dec 25, 2011 | 1995 Toyota Camry
Jan 08, 2011 | 1991 Toyota Camry
Nov 17, 2010 | 1991 Toyota Camry
Oct 05, 2009 | 1993 Toyota Camry V6
Jul 09, 2009 | 1991 Toyota Camry
Feb 03, 2009 | 1993 Toyota Camry V6
Nov 18, 2017 | Nissan Cars & Trucks
30 people viewed this question
Usually answered in minutes!