Question about Cars & Trucks

Open Question

Engine removal It has a 353 detroit deisel in it with automatic transmission and can only get it to come apart about half inch and will not come any further

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is serial # of DUETZ engine THAT is in 240A timberjack skidder


Not sure if you mean engine size or not . Each engine has it's own serial number. Anyway the Duetz engines were 130 HP 6 Cylinders. Now Duetz had 912 and 913 engines the 913 was the model with a turbo and they produced these engines in 3,4,5,and 6 cylinders. Most of what I've seen is the 6 - 130 HP. This particular unit was built in the mid 80's or so. Other Timberjacks different models/years, etc, also had 4 cylinder cummings, then some John Deere also. If my memory serves me correct it seems like I ran up on an old Timberjack in the woods hunting one day and it had a Detroit 353 in it. Great little engines.

Jan 01, 2015 | Cars & Trucks

1 Answer

Uninstalling an Automatic transmission 2003 escape??


have you taken all the bolts out, including torque convertor & removed starter and axles ??

Apr 08, 2014 | 2003 Ford Escape

1 Answer

6v92 detroit deisel


The only thing that keeps a diesel engine from running.. OTHER THAN A MECHANACAL PROBLEM.. is lack of fuel. Since it starts when you spray starting spray the engine probably does not have a mechanical problem 1. does the fuel solenoid open when you energize it?, is the fuel filter clogged?, is the lift pump working? Is there fuel in the tank? IF YOU HAVE RUN OUT OF FUEL YOU WILL NEED TO BLEED THE AIR OUT OF THE FUEL SYSTEM.

Mar 07, 2014 | Cars & Trucks

2 Answers

Rear oil seal leaking. how to fix


If your sure the rear main seal is leaking then the engine and transmission have to be separated. It is easier to remove the transmission. If it's an automatic then after trans removal, you have to remove the flex plate to expose the seal. If it's a manual then the flywheel has to be removed after trans removal. It is a one piece seal that can be pryed out gently and a new one pressed in.

Jan 08, 2011 | 1991 Chevrolet S-10 Blazer

1 Answer

1995 Saturn SL2 Automatic. Will not shift into gear when first started. Must warm up first, sometimes for 20-30 minutes. Engine starts right up and runs good. What do I need to fix? Thank you Robert


you have dirty cervo valves.Pour one pint of deisel fuel into transmission let run for approx.5 minutes.Drain all of fluid out.Change filter on front of transmission(it looks like a oil filter)replace fluid and that should take care of problem.

Jun 11, 2010 | 1993 Saturn SL2

1 Answer

Can you change seals on the supply pump return line


If you just want to change the seal at the fuel lines, you may be able to if you have enough patience and a few specially bent wrenches. It is much easier to remove the turbo. If you do remove the turbo don't forget to replace the two o-rings. If you want to remove the pump completly (most of the time a new pump is needed to repair a leak), then I would remove the fuel supply tube bolt from the back of the pump, remove the fuel lines from both heads, replacing the grommets with the updated grommet which resist breaking apart from the newer fuels. Then remove the two bolts from the pump and rotate the engine by hand untill the pump comes up about a half inch. This way if the tappet falls out of the pump the cam lobe will be up enough that it will not fall down into the engine. Then you can replace the o-ring at the bottem of the pump and all the rest of the seals or the entire pump. Don't forget when going back together seat the pump and then rotate the engine by hand again untill the pump sits almost flush and then torque everything. The fuel supply tube should be about 40 ft. lbs. The bolts are probably around 120 inch lbs like everything else but just use good judgement. You can make a clicking sound while using a regular ratchet if it makes you feel better.

Apr 15, 2009 | 1995 Ford F350

1 Answer

Engine Specs.


you should ask for the advance tool if you are buying one . i had 8 of the screaming boat anchors and i can't recall if it's a 1771 or a 1441 and be sure you don't split the rack or it will not pull the hat off your head

Apr 06, 2009 | 1990 GMC S-15 Jimmy

1 Answer

89 chevy 2500 series 4x4 automatic transmission filter repair


there are to bolt looking things about an inch apart it goes between them

Feb 02, 2009 | 1989 Chevrolet C/K 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...