Question about Cars & Trucks

Open Question

Pioneer 639ta How to remove the 639TA from a Honda CRV (2000) without removing the complete dashboard? Do I eed a special tool for this??

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 117 Answers

SOURCE: head gasket replacement

I'm assuming you have the 5 cylinder engine. Changing the gasket is a pig of a job, especially it it's a T5. AFAIK you don't need a special tool to hold the camshafts in place (at least, I had no trouble) although it makes it easier when you replace them. I can't detail the process here as it's too involved but I will mention one point: On the T5, there is a support bracket between the exhaust manifold and the block which is *not mentioned* either in the official workshop manual or Haynes! I don't know if it's present on non-turbo models. If you have a T5 I would seriously consider getting a spare engine from a breaker rather than changing the gasket - it really is that bad :{{{

Posted on Jul 20, 2008

  • 2920 Answers

SOURCE: thermostat removal 2000 malibu

all you need is a ratchet and socket that will fit the bolts and you should be good to go

Posted on Feb 20, 2009

  • 87 Answers

SOURCE: wiper arm removal

loosen the nut on the wiper arm and gently pull on wiper arm and hit the nut with a rubber mallet

Posted on Mar 09, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

  • 1986 Answers

SOURCE: Need instructions on RF door panel 2000 deville

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i open the interior fusebox in my honda hrv 2000 model. Thankyou.

Kathryn, Not familiar with Honda hrv, did you mean CRV. There will be a small trim door to remove, lower dash by drivers left knee to access interior fuse panel.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Fuse Box layout on 2000 CRV Honda Tech
Interior Fuse Box Location 1997 2001 Honda CR 2000 Honda CR EX 2 0L 4 Cyl
Thread What are these Definitions

Jun 18, 2016 | Honda HRV Cars & Trucks

1 Answer

How do you release the headlight retaining clip on 1998 crv

Click HERE to view video of a 2000 CRV bulbe replacement , it is the same.

Feb 22, 2012 | 1998 Honda CR-V

1 Answer

I have a flat tire, but do not have the special tool to take off the bolt. Any ideas? 2010 Honda CRV

Most auto parts stores have Locking Lug Nut removal tools. If you know the size of your lug nut you may be able to buy a single tool that fits on a standard ratchet to remove the locking lug nut. If your lug nut is the type that spins without the proper tool to remove it, your best bet is a mechanic with the proper equipment to avoid doing damage to the wheel or stud.

Good luck!

Jul 05, 2011 | 2004 Honda CR-V

1 Answer

Having trouble replacing starter in my 2003 Honda CRV. Cannot remove the Starter Mounting Bolts, can barley access with fingertips. Is there a special tool or trick to removing the old starter?

imjustavg_1.gifNo there is not a trick, just very tight. If you aren't using a socket set with an extention it is almost impossible to get the bolts out though.

Jun 22, 2011 | 2003 Honda CR-V

1 Answer

How to replace a Honda CRV 2000 thermostat?

Welcome to
Thank you for using, Regards, Lee Davidian Remove upper radiator hose
Remove the two 8 mm bolts See diagram below bc52022.png

Sep 16, 2010 | 2000 Honda CR-V

2 Answers

How do you change the clock on a 2001 honda crv

The clock removal instructions are available at
If you have a defective clock, we offer a very reasonable repair service with a lifetime guarantee.

Subaru Forester 1998 - 2002
Subaru Impreza/WRX 2002 - 2005
Toyota 4Runner 1996 - 2002
Nissan Pathfinder 1996 - 2004
Honda CRV 1996 - 2001
Toyota Tacoma 1995 - 2004
Toyota Rav4 1996 - 2000
Toyota Land Cruiser 1996 - 2002
Toyota Camry/Corolla 1996 - 2004
Lexus ES300, GS300 1997 - 2004
Saab 9-2x 2004 - 2006
Toyota Matrix 2003 - 2008
Toyota Sienna 1999 - 2003
Ponitac Vibe (Voltz) 2003 - 2008
Suzuki Aerio, Vitara mid 2000s

May 31, 2010 | 2001 Honda CR-V

1 Answer

I need to replace the rotors and brake pads on a 2007 Honda CRV

some calipers have pistons in them that need to be screwed back in that requires a special tool.can be picked up at your local parts store fairly cheaply

Sep 06, 2009 | 2002 Honda CR-V

1 Answer

I Have a pioneer radio, DEH-1900MP in my 2000 ford focus. I need to know how to remove it so that I can repair an air conditioning malfunction.

Vehicles with high output amplifier and subwoofer
  1. Using a common radio remover, detach the audio unit.
    1. Insert the common radio remover into the locating holes. Pull the tools gently to the left and right of the audio unit to release the locking tangs.
    1. Slide the audio unit out of the instrument panel.
  1. Remove the audio unit.
    • Disconnect the audio unit electrical connectors.
All except vehicles with high output amplifier and subwoofer
  1. Using the special tools, detach the audio unit.
    1. Insert the special tools into the locating holes. Pull the tools gently to the left and right of the audio unit to release the locking tangs.
    1. Slide the audio unit out of the instrument panel.
  1. Remove the audio unit.
    • Disconnect the audio unit electrical connectors.
please rate, thanks

Jul 03, 2009 | 2000 Ford Focus

1 Answer

1998 CRV Radiator and A/C condensor

There is no special tools needed you must evacuate a/c system if it did not already lose all freon from hit.

here is manual instructions:

  1. Drain the engine coolant.
  2. Remove the upper and lower radiator hoses, and ATF cooler hoses.
  3. Disconnect the fan motor connector.
  4. Remove the radiator upper bracket, then pull up the radiator.
  5. Remove the fan shroud assemblies and other parts from the radiator.
  6. Install the radiator in the reverse order of removal. NOTE:
    • Set the upper and lower cushions securely.
    • Fill the radiator with engine coolant and bleed the air.

Aug 25, 2008 | 1998 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides