Question about 2000 Ford Contour

Open Question

How do i replace a turn signal flasher on a 2000 ford contour?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: 2000 FORD EXPLORER FLASHERS WORK

If fuse 10 in the fuse box is good, which I assume it is or you would have other functions not working then the problem may be the combination flasher module or the multifunction switch, the flasher is the cheaper of the 2 parts ($12) so I would try it first, you might be asking why would this cause the problem when the 4 ways work, well like I said it is a solid state unit and operates both the flashers and 4 ways independent of each other, if that is not it then the problem is the turn signal switch.

Posted on Oct 20, 2008

  • 3 Answers

SOURCE: 1998 Ford Ranger XLT turn signals, hazzard flasher not working

wire plugin on back of turnsignal switch not making a connecting

Posted on Jan 15, 2009

aoogha
  • 119 Answers

SOURCE: replacing a fuel pump on a Ford Contour

Fuel Pump Module —Vehicles with Returnless Fuel System
Special Tool(s) Wrench, Sender Unit, Fuel Tank
310-065A (23-054) Removal
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.

  1. Remove the fuel tank.
  1. Using the special tool, remove the fuel pump locking ring.
  1. Remove the fuel pump module.
    • Rotate the pump counterclockwise to remove.
  1. Remove and discard the O-ring seal.
Installation
syp~us~en~file=ani_caut.gif~gen~ref.gif WARNING: Do not smoke or carry lighted tobacco or open flame of any type when working on or near any fuel related components. Highly flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
  1. Install a new O-ring seal and locking ring.
  1. To install, reverse the removal procedure.

Posted on Jan 09, 2010

  • 4369 Answers

SOURCE: where is the turn signal\hazard flasher located?

it's in the auxiliary relay box behind the glove box.

13350 is base part number on flasher

Posted on Feb 03, 2010

Testimonial: "Actually found it located behind the radio mounted on a brace. Removed cover and relay pulls out. About 1" cube with 5 terminals on it."

ZJLimited
  • 17970 Answers

SOURCE: 99 ford contour hazard flasher unit where is it

Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column

  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Posted on Apr 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Ford Contour sedan. Signal flasher clicks constantly even when lever is in center position.


likely a multifunction switch problem but first try to replace the 4 way flasher with the signal flasher located under the steering colum fallow the clicking to locat flasher

Nov 21, 2010 | 1997 Ford Contour

1 Answer

99 ford contour hazard flasher unit where is it


Flashers - REPLACEMENT

Turn Signal Flasher
(see Figure 1)

e21631a.jpg

Fig. 1: The turn signal flasher is located on the multi-function switch in the steering column
  1. Disconnect the negative battery cable.
  2. Remove the upper and lower steering column shrouds.
  3. Pull the flasher from the back of the multi-function switch.

To install:
  1. Install a new flasher in the multi-function switch.
  2. Install the column shrouds.
  3. Connect the negative battery cable.

Hazard Warning Flasher
  1. Disconnect the negative battery cable.
  2. Remove the knee bolster panel from the underside of the driver's side of the instrument panel.
  3. Grasp and pull the flasher from the connector located near the top of the steering column.

To install:
  1. Install a new flasher in the connector.
  2. Install the knee bolster panel.
  3. Connect the negative battery cable.

Hope this help (remember comment and rated this).

Apr 02, 2010 | Ford Contour Cars & Trucks

1 Answer

In my 1996 Ford Contour, my hazards work but my turn signals do not. Can you help?


The hazard fuse and the turn fuse are different ones the turn flasher is different than the hasard flasher and the hasard button is the flasher. You may have to play with the switch a bunch to get it to work and it may only work a few times and quit even after doing this. Fuses good and you get it to work just once by a new switch and yor back in bussness

Dec 05, 2009 | 1996 Ford Contour

1 Answer

Right Turn Signal sitll not working eventhough I replaced the flasher


are you sure the bulb is good? have you had the steering column out recently? if so make sure the plug going into your switch isnt being pulled as it will cause a bad connection. but it sounds like you need a new turn signal switch

May 05, 2009 | 1998 Ford Contour

1 Answer

Both front and rear turn signals stopped working


Your turn signal flasher needs to be replaced (the hazard flasher is separate unit). Your owners manual should have the location of the turn signal flasher (usually on the fuse block under the dash).

Mar 19, 2009 | 1999 Ford Contour

2 Answers

Turning signals not working


your problem is call a relay is under the dash .need to buy flasher relay at advance auto parts, pep boys, or any oder auto part store.

Oct 11, 2008 | 1998 Ford Contour

Not finding what you are looking for?
2000 Ford Contour Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...