Question about 2008 Dodge Caliber 2.0

Open Question

Size socket needed remove wheel bearing nut - 2008 Dodge Caliber 2.0

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1118 Answers

SOURCE: Shadtree replacement of a front wheel bearing possible?

the nut is special its metric, the parts store will know its like a 30or35. i know an inch and a half socket is to small If you got the tool i see no problem. you may have to tap on it a little but it should come right out.

Posted on Feb 04, 2009

polarcycle
  • 1392 Answers

SOURCE: changing wheel bearing?

Should be 1 1/4", or 34mm.

Posted on Mar 08, 2009

  • 412 Answers

SOURCE: i am replacing the right front wheel bearing hub assembly .

you need an 1 3/4" socket

Posted on May 23, 2009

  • 137 Answers

SOURCE: What size socket for a front wheel bearing hub nut

36mm

Posted on Jul 11, 2009

  • 157 Answers

SOURCE: I need the size of the nut to remove wheel joint

Some places like Harbor Freight have cheap Vernier calipers, which you should be able to measure the nut. Auto parts stores may have them, or department stores. I am sure Sears has them, but they may be better quality, so they will cost more. Google all those kind of stores that are close to where you live, and search for vernier calipers.

Posted on Aug 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

1 Answer

How to replace rear wheel bearing/hub 2006 scion tc


loosen wheel lug nuts, jack up rear of car and put jack stands under supporting it, remove lug nuts, remove wheels, on back of wheel bearings is a sensor, a 10 mm socket will remove to be careful not to damage this, now on wheel, you will have to remove the caliper and support a 17 mm socket should do this and a breaker bar, once caliper and brake assembly is out the way, you need to remove the holders on the rotor, a pair of needle nose pliers will do it, now you can remove the rotor, once this is done, behind the backing plate, are 4 bolts, not sure of size ,these need to be removed to let the wheel bearing assembly to come out, you will need to tap on the wheel bearing, to loosen it , reverse the procedure to install

Feb 02, 2011 | Scion TC Cars & Trucks

1 Answer

How do i repair left front hub & bearing assembly on a 2000 ford taurus v6 24v dohc


BEST TO GET A HAYNES REPAIR MANUAL IT HAS PHOTOS AND INSTRUCTIONS ON HOW TO REMOVE HUB BEARING ASSEMBLY.YOU WILL NEED A 1/2 SIZE TORQUE WRENCH FOR HUB RETAINING NUT.ITS TORQUE IS 170 - 202 FT LBS.MAKE SURE YOUR TORQUE WRENCH MAXIMUM RANGE IS AT LEAST OVER 200 FT LBS TORQUE.YOU WILL ALSO NEED A AXLE NUT SOCKET.ITS A BLACK SOCKET LIKE IMPACT SOCKET.ITS GRADE 8 STEEL.YOU HAVE TO USE THIS TYPE.A REGULAR SOCKET WILL BREAK.WHEN REMOVING AXLE NUT.ITS ON TIGHT.YOU WILL ALSO NEED A 1/2 BREAK BAR TO BREAK IT A LOOSE.ALSO REMOVE WHEEL COVER.WITH CAR WEIGHT ON WHEEL YOU HAVE TO LOOSEN AXLE NUT A LITTLE.NOT ALL THE WAY UNTIL YOU GET CAR OFF GROUND.WORK SAFE BECAREFUL.

Oct 28, 2009 | 2000 Ford Taurus

Not finding what you are looking for?
2008 Dodge Caliber 2.0 Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...