Question about Cars & Trucks

Open Question

Flywheel torque 3c 2.2 toyota engine - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Torque spec for flywheel bolt: Isuzu 2.5 diesel engine

normally 110 nueton metres. use nut lock and once you have torqued you will feel if you have to tighten it a bit more.

Posted on Aug 15, 2008

  • 3 Answers

SOURCE: I would to know the cylinderhead torque for a 3c 2.2 diesel

1st 48ft-lbf

2nd turn 90 degrees

3rd turn 90 degrees

Posted on Sep 10, 2009

Testimonial: "Hi, that was very helpful, I appreciate it very much. Thank you. Even thou I didn't get the sequence and stages of the torque"

  • 1 Answer

SOURCE: Wiring Diagram for 3TC-TE.

did you have Diagram for 3TC-TE.now

Posted on Apr 09, 2010

alicantecoli
  • 22156 Answers

SOURCE: need torque specs on flywheel to crankshaft for

go by the size of the bolt shank the thicker the bolt the more the torque ,also use some form of locktite on them or contact adhesive will do ,if a 15mm head then about 65lb if 17mm then 75lb and 19 mm 85lb ,and dont forget the sticky stuff

Posted on Sep 02, 2010

rohdd
  • 283 Answers

SOURCE: 89 toyota pickup torque specs. for flywheel and

Thoroughly clean the flywheel bolts. Coat the first 3 or 4 threads of each bolt with sealant. Install the flywheel, aligning the previously made marks. Install the bolts finger-tight.
Tighten the bolts in a crisscross pattern and in several passes to the correct tightness:

  • 22R/22R-E manual trans-80 ft. lbs. (108 Nm)
  • 14-20 ft-lb for the clutch cover and
  • 50 ft-lb for the transmission mounting bolts.
Since you have the flywheel off, be sure and inspect the rear main seal. Now might be a good time to replace it. Be sure the rear flange of the flywheel is clean before re-install.
Be sure to inspect or, better yet, replace the bronze pilot bushing. I f you don't know how to get it out leave a comment. J


Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is really appreciated for the FREE answering of your question.

Posted on Feb 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Torque setting for yaris t1


here you go an on line page with all your specs just write down the ones you need. off save page for off line viewing.
http://www.allwidewallpapers.com/2007-toyota-yaris-engine-specifications/MjAwNy10b3lvdGEteWFyaXMtZW5naW5lLXNwZWNpZmljYXRpb25z

Jun 22, 2016 | 2007 Toyota Yaris

1 Answer

I have a 94 Hyundai Excel. I am replacing the clutch but can't find the torque settings anywhere.


clutch/flywheel torque settings - Hyundai Forums : Hyundai Forum

www.hyundai-forums.com/...accent/146383-clutch-flywheel-torque-setti...

Aug 2, 2012 - 3 posts - ‎2 authors
Im after the torque setting for the clutch and fly wheel for a lc 2000 accent with the dohc 16v engine. cheers.Missing: .94

Torque value head bolts 1994 hyundai excel 1.5l - Fixya

www.fixya.com/cars/t12339610-torque_value_head_bolts_1994_hyundai
Apr 7, 2012 - SOURCE: torque settings for a hyundai accent 1500 1998. cylinder ...SOURCE: how d i change a clutch in a hyundai excel 1994. Hi first lift the ...

Flywheel & Pressure Plate Torque Specifications? - Hyundai ...

www.hyundaiaftermarket.org > ... > Engine, Intake, Exhaust

Dec 19, 2015 | Hyundai Cars & Trucks

1 Answer

Toyota 2c. I need cylinder head and flywheel Torque settings


Toyota 2c ...
USE NEW BOLTS...
Torque sequence:
You're driving a diesel single cylinder head engine. Engine head torque has to be done in specific order and stages if not can warp head or break bolts. Suggest you get torque sequence and torque specs from your Toyota dealer, they can give you correct answer. Don't trust answers on here, if you choose wrong specs. could end up messing up head.


Flywheel - Use a Sealer on bolt, Manual Transmission 88nm/65 ft lb... Auto Transmission 74nm/55 ft lb

Aug 06, 2014 | Cars & Trucks

1 Answer

Reduced torque and high temperature on toyota lucida 2.2 ltr. 3C diesel during steep grade. Problem also show if the vehicle is heavily loaded


yeap we have this problem, we had the radiator flushed and it fully serviced.problem came back.no visible water leak under pressure test by mechanic.ours turned out to be the head gasket.not good.new engine .not worth trouble

Jan 31, 2011 | Toyota Previa Cars & Trucks

1 Answer

We are installing a re-built engine (3.0,V6) into this truck and are trying to find torque specs on flywheel bolts


Hello steve29654: My name is Roger and I will help you. The correct flywheel torque is. 3.0 engine with automatic transmission is 61 ft. lbs. For a engine with standard transmission the torque is 65 ft. lbs. Should you need further help please just ask. Please rate the answer. Thank You for using Fix Ya. Roger

Mar 25, 2010 | 1992 Toyota Pickup

2 Answers

Wiring Diagram for 3TC-TE.


did you have Diagram for 3TC-TE.now

Nov 10, 2009 | 1997 Toyota Previa

1 Answer

I would to know the cylinderhead torque for a 3c 2.2 diesel


1st 48ft-lbf

2nd turn 90 degrees

3rd turn 90 degrees

Sep 09, 2009 | 1994 Toyota Previa

1 Answer

Engine Problems


There is no 3c engine in a Toyota Supra. If you have a 1995 it would have a 1JZ-GE, 1JZ-GTE, 2JZ-GE, or 2JZ-GTE if you can tell me which engine you have I can further assist you.

Dec 28, 2008 | 1995 Toyota Supra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...