Question about 2001 Pontiac Aztek

Open Question

Codes po336 i need to know how to relearn the crank position sensor on a 3.4l aztek thank u

Posted by on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 9 Answers

SOURCE: I ran the OBII code

look behind the Crank pully you

Posted on Sep 01, 2008


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2005 tahoe 5.3l two codes po300 and po336

Multiple cylinder misfire and crankshaft position sensor. Replace CKP sensor and perform CKP relearn with scanner, clear codes and recheck.

Feb 18, 2014 | Cars & Trucks

1 Answer

Are po101 and po336 related

I doubt it.

Code 101 is for a problem with the mass air flow sensor, and code 336 is for a problem with the crank sensor.
Those sensors and circuits would need to be tested.

Jan 08, 2013 | 2007 Chevrolet Tahoe

1 Answer

P0335 code,05 kia rio, changed crank sensor, did not help?

Did you do a crank relearn ? Could be a wiring issue , control module problem etc... Testing electrical circuit first , video's on youtube , all you would need is a DVOM - digital volt ohm meter . P0335 Kia Crankshaft Position Sensor Circuit c Replacing Crankshaft Position Sensor Code P0335

Jun 05, 2011 | 2005 Kia Rio

3 Answers

Codes read PO335, PO304, PO336 i need to know what they are for, Please !!

304 is misfire on cylinder #4. #4 is the middle cylinder on the driver's side.
The other 2 relate to the crankshaft sensor:

P0335 Crankshaft position (CKP) sensor -

possible causes: circuit malfunction Wiring, CKP sensor, ECM

P0336 Crankshaft position (CKP) sensor - range/performance problem
possible causes: insecure sensor/rotor, air gap, wiring, CKP sensor

Is the car running? If yes, check for a loose connector on the crank sensor. You may need to take the connector off and see if there is any corrosion on the terminals. If yes, do your best to clean with a small screwdriver and/or electrical parts cleaner.

From what I can tell, the sensor is on the bottom of the engine near the idler arm, but it has a long pigtail such that the connector is on top of the engine by the fuel rail. See pictures below.

for the misfire,

Please see my tip at . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.




Dec 18, 2010 | 1998 Cadillac Catera

1 Answer


I punched in code po336 for a bing search,
and it says that it could be
Crankshaft Position Sensor Signal Range / Performance
But it may be for another car.

What was your engine size and submodel? My reference on the Internet didn't have fault codes for your vehicle.

Jul 07, 2010 | 1997 Buick Skylark

1 Answer

OBD malfunction indicator light status on stored diagnostic trouble codes po325, po335, p1336 . Car will not pass OBD test.


Aug 28, 2009 | 1997 Nissan.5 Altima

1 Answer

1999 chevrolet lumina 3100 crank sensor code

I have found that the knock sensor will do the same thing

Dec 01, 2008 | 1999 Chevrolet Lumina

Not finding what you are looking for?
2001 Pontiac Aztek Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts


Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8522 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides