Question about Nissan Cars & Trucks

1 Answer

Replace engine thermastat on a nissan quest - Nissan Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Nissan Master
  • 21,873 Answers

If the van is a 1999 or older model the thermostat is on the side of the engine behind the belts. Not an easy job.

Posted on May 02, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 1995 nissan quest

Have your engine mounts checked. I was experiencing the same type if things, and it turned out all 5 were cracked! (I also have the 1995).

Posted on Oct 23, 2008

  • 4369 Answers

SOURCE: 1999 nissan quest brake pad replacement

Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Posted on Jan 21, 2009

  • 30 Answers

SOURCE: replace control panel on 2004 nissan quest

there is a c-clip you need a small screwdriver to pull it out then gearshift knob will pull off

Posted on Jan 28, 2009

  • 840 Answers

SOURCE: replacing belts after replacing water pump on 1996 nissan quest x

the easist way is to loosen the alternator slide the alternator down then slide the belt where it should go then pull up on the alternator again and bolt up Please rate my response thank you very much

Posted on Jan 30, 2009

johnjohn2
  • 5763 Answers

SOURCE: 1997 nissan quest camshaft sensor where is it & how to replace it

The camshaft sensor is located inside the distributor and is part of it, in order to replace it you must replace the distributor,to replace remove the dist cap. mark the location of the rotor,by marking where its pointing to, then mark the dist housing, so now theres a mark on the rotor and housing to show where rotor points, next mark the location of dist going into housing, mark the shaft and the block,because it spins in block this way you can line back up.next remove hold down bolt and pull out,mark the new dist in exacat same spots as the old so you can install back the same,you may have to put it in and pull it out until your marks are lined up,this way the timing will be dead on, when done you can check timing. good luck

Posted on May 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replacing the timing belt on a 2000 Nissan Quest/ Instructions Needed


Charles,your engine is a interference one,and you may have damaged it or ruined it,here's a link on replacing the belt. Damage to the valves and/or pistons may resulted from belt breakage.

Nov 20, 2013 | 2000 Nissan Quest

1 Answer

How to change a thermastat on a 1994 nissan qwest van


Follow the top radiator hose to the motor. Unbolt the fitting the thermostat is under there seal and replace.

Oct 14, 2010 | 1994 Nissan Quest

1 Answer

How many miles to replace timing belt for nissan quest 1996


spec is 105,000 miles, but they go 150K easily. If it breaks, it won't cause any damage to the engine.

http://groups.yahoo.com/group/villagerquest/

May 21, 2010 | 1996 Nissan Quest

1 Answer

1996 Quest: how many miles to replace timing belt for nissan q...


it's a freewheeling engine. Interval is 105,000 but most go to 160,000 easily.

I would just kep driving, no engine damage will happen if it breaks. engine will just stall.

http://groups.yahoo.com/group/villagerquest/

May 18, 2010 | 1996 Nissan Quest

3 Answers

Nissan Quest 1996 won't start. Battery good.


tap the starter at the same time turning the key. if it starts ,replace starter.

Mar 14, 2010 | 1996 Nissan Quest

2 Answers

P0440, Nissan quest


the most common cause of this in Nissan is a defective carbon cannister vapor purge valve in the evaporative emission control system.

Dec 23, 2009 | 1998 Nissan Quest

4 Answers

Does the nissan quest 1999 timing belt needs to be


The Quest has a non interference engine meaning that should the belt break the engine would just die without breaking anything. Nissan recommends 105K for changing but that depends on the way the vehicle was driven (driving habits), road conditions etc. If driving on roads for e.g. that are hilly, it labors the engine more thus shortens the lifespan of the belt according to mfg.

Dec 03, 2009 | 1999 Nissan Quest

2 Answers

1994 nissan quest crankshaft rear main seal removal


u don't have to remove the engine however you must remove the transmission and flywheel, you will also need the Nissan special tool to install the new full circle seal or it will leak.

Jul 28, 2009 | 1994 Nissan Quest

1 Answer

Throttle body just replaced; now runs & idles rough


adjust the TPS, throttle position sensor.

First though, disconnect battery for 1/2 hour. Restart engine and drive for 15 miles while computer relearns changes you made. Will run rough for this period.

Apr 25, 2009 | 2005 Nissan Quest

1 Answer

2000 nissan quest over heating


you have air trapped in the system.

Go to this site for help

http://autos.groups.yahoo.com/group/villagerquest/

Sep 29, 2008 | 2000 Nissan Quest

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...