Question about Cars & Trucks

Open Question

2005 mazda 6 intake manifold leak repair manual

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: 2001 mazda tribute spark plug change

can 't you remove the coils insted of the intake ? It is much easier.

Posted on Dec 02, 2008

Ad
  • 334 Answers

SOURCE: water leaking from intake manifold

the chev are fames for intake manifold seeping. it will have to be replaced soon good luck

Posted on Mar 24, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

bschilz
  • 2049 Answers

SOURCE: serpentine belt diagram mazda 6 2005

Here are links to the diagram...

If your engine is the 2.3L 4 cyl... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7042

If your engine is the 3.0L V6... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S6036

Posted on Sep 01, 2009

  • 12153 Answers

SOURCE: My 1999 chevy tahoe is leaking antifreeze. I

it could but- check passenger side front where heater core line go into manifold right behind alternator the hose line is connected by a press clip into an alloy fitting this fitting gets eaten away by anti freeze and hose angle pulls back on fitting the part is $18 at dealer and is screwed into manifold use caution if ur r going to replace at very edge of aluminum manifold---and check ur water pump bolts the 2 longer ones should have a lock sealant on them they bolt in thru a water jacket

Posted on Oct 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is my idle control sensor valve located and how do i change it. Car is a mazda 6 6cyl 2005


Check for vacuum leaks first, the valve is a rotary valve that is cylindrical in shape, the intake hose will attach to the Tube from the Air Filter housing to the Manifold and the exit side goes straight to the Manifold. You may try cleaning it before replacing it first.

Oct 22, 2015 | Mazda Cars & Trucks

1 Answer

Intake manifold torque specs


Intake is about 42 foot pounds. Upper intake is 12 foot pounds. Start in the center and work back and forth to the outer bolts. Snug them first (around 25) then set them at 42. Upper also start at center but torque them down.

Aug 29, 2015 | 2005 Mazda 6

2 Answers

Cant locate pcv valve on my 2005 mazda 3


Look under the intake manifold on the backside of the throttle body. If its turbocharged, you will have to pull the intercooler out to get to it.

Jan 05, 2010 | 2006 Mazda 3

2 Answers

Mazda mpv 2005 vacum leak


99% of the time it's a pcv hose, put your hand behind the intake manifold while the car is running and you should be able to feel it. it will be sucked in at the elbow on the manifold, this is not an easy hose to replace.

Oct 20, 2008 | 2005 Mazda MPV

1 Answer

Intake engine manifold qt.


Based on local labor rates (which may be different in your area), the estimate to repair your vacuum leak at your intake (also assuming the intake will have to come off the engine to fix the leak), the cost will be around $350.00. Is it a 4 cylinder or 6?

Chris

Aug 01, 2008 | 1995 Mazda 626

2 Answers

Engine cut out


take it to a place where they have a smoke machine this machine aply smake to the engine and will show up the leak right away

May 27, 2008 | 2005 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...