Question about Chrysler Cars & Trucks

Open Question

On 2007 chrysler sebring 2.4 L eng. where does intake manifold runner position sensor located & manifold flow valve ?\

Check eng. light on w/code p2017 -- intake manifold runner position sensor/switch circuit high bank 1

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
warlock61
  • 659 Answers

SOURCE: i have code 1538 on my check engine for 1998 ford windstar ,does

on the passenger side of the engine you will see 2 small metal rods at the top of the engine just below the intake manifold there are little white clips that hold the rods on these clips usually break and the rods come off

Posted on Mar 28, 2009

Ad
66 chrgr
  • 1011 Answers

SOURCE: INTAKE MANIFOLD CONTRL RUNNER VAVLE LOCATIONS

they are on the back side of the motor just above the transmission .take off the dog house and you will see the unit.

Posted on Jan 25, 2009

  • 107 Answers

SOURCE: the computer says Random / muliple cylinder misfire detected

look for a vacuum leak

Posted on Feb 27, 2009

  • 218 Answers

SOURCE: Check engine light came on

THERE IS A VALVE ON THE RIGHT SIDE OF THE INTAKE MANIFOLD THAT OPEN THE RUNNER.IT HAS A VACUUM LINE TO IT.FOR IT TO BE STUCK OPEN EITHER THE SOLENOID IS BAD,THE VACUUM LINE IS BAD OR THE RUNNER IS GUMMED UP WITH CARBON AND STUCK OPEN

Posted on May 15, 2009

  • 7353 Answers

SOURCE: I got a code P2004

what engine? So the guy running the test could'nt point it out to you? You need to find a shop that qualified to repair the car. its a valve on the intake manifold that opens and closes to help th engine produce the most power at low and high rpm. they get stuck. sometimes you can clean them.

Posted on Oct 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2008 dodge avenger code p2004


Intake Manifold runner control stuck open - bank one:
- Intake Manifold Runner Binding Or Sticking
- Faulty Manifold flow valve
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection

There is a factory service bulletin for this problem for 2007-2008 Dodge Avengers. (JS)

Sep 22, 2015 | Dodge Cars & Trucks

1 Answer

What does p2004 and p2017 mean?


p2004= intake Manifold runner control stuck in position
p2017 = - Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection
- Faulty Manifold flow valve
- Intake manifold
- Faulty Powertrain Control Module (PCM)

Jul 12, 2014 | 2007 Jeep Compass Limited

1 Answer

How do you fix a intake manufacture runner control thats stuck open


I not familiar with a "intake manufacture runner control". Do you mean intake manifold? Not you sure what a runner control is though. Could give us some more detailed information?

Jun 13, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

P2078


this is also known as the short runner valve i have attached a shematic to help identify it for you2012-01-04_183346_srv.jpg

May 09, 2014 | 2008 Chrysler Sebring Convertible

1 Answer

Code p2017 on a chrysler sebring


Here is the definition.

P2017 CHRYSLER - Intake Manifold Runner Position Sensor/Switch Circuit High Bank 1

Possible causes - -
- Manifold flow valve harness is open or shorted
- Manifold flow valve circuit poor electrical connection
- Faulty Manifold flow valve
- Faulty Powertrain Control Module (PCM)

You'll need someone with a shop manual to get the testing procedures.

Apr 14, 2013 | 2007 Chrysler Sebring Sedan

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

1 Answer

Went to autozone they diagnostic it said intake manifold runner stuck open code P2004 we have no idea what that means please help.


The intake manifold runner valve system is mounted on the intake manifold and consists of the intake manifold runner valve (IMRV), the IMRV motor and the IMRV position sensor. The IMRV motor opens and closes the IMRV using multiple gears. The valve position sensor detects the opening angle of the IMRV. The IMRV has a groove on its upper portion. When the IMRV is closed, air flows through a groove into the cylinder from the intake manifold, so that a dynamic air flow or "tumble" air flow is generated in the cylinder. The tumble air flow drastically reduces fuel deposits inside the intake air port and the combustion wall surface inside the cylinder. This improves the combustion efficiency by boosting the air−fuel mixture and air flow turbulence.

Check this document for Diagnosis procedures and more information:
http://www.4shared.com/document/OGI6_zov/INTAKE_MANIFOLD_RUNNER_CONTROL.html

Aug 03, 2011 | 2009 Dodge Avenger

1 Answer

I got a code P2004'' when a diagnostic test was ran on my 2007 Chrysler Sebring that said my intake runner controller bank was stuck ''open''. Can you help me find an answer to this.


what engine? So the guy running the test could'nt point it out to you? You need to find a shop that qualified to repair the car. its a valve on the intake manifold that opens and closes to help th engine produce the most power at low and high rpm. they get stuck. sometimes you can clean them.

Oct 01, 2009 | 2007 Chrysler Sebring Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...