Question about GMC Suburban

Open Question

Where is the obd2 connector located on a 1998 GMC suburban

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
66 chrgr
  • 1011 Answers

SOURCE: 1999 suburban gmc - where's the starter?

on bottom back of engine on the passenger side of engine

Posted on Feb 19, 2009

Ad
  • 245 Answers

SOURCE: Hi!Where is the OBD2 connector located on 1992 mit

drivers side at the bottom of the dash plastic look down by the floor where the dash ends it should be right in that area

Posted on May 02, 2009

SOURCE: I am looking for OBD2 connector in my Nissan

dear friend-the OBD2 connector that you are looking for is underneath the fusebox underneath the steering.

Posted on Jul 23, 2009

  • 191 Answers

SOURCE: Where is transmission fluid fill on '86 GMC Suburban

get a funnel and pour it into the dip stick hole that you use to check the fluid level with.

Posted on Jan 01, 2010

  • 507 Answers

SOURCE: Where is the OBD2 connector located? 2002 F150

under the steering colum near fuse box, brake pedal, gas pedal area. and if you don't know where to hook it up at, odds are you don't know how to fix the problem with your $100 scan tool. Put your nose in some books and learn before you try. That or find someone who will walk you through it.

Posted on Jan 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My left tail light and turn light not working on 1998 gmc suburban. Bulb is fine.


Sounds like you have a bad tail light circuit board.

unplug the connector and use a test light to confirm there is power to the circuit board for the lights that do not work. If there is power replace the circuit board. They are usually in stock at your local parts store.

Feb 09, 2012 | 1998 GMC Suburban

1 Answer

1998 GMC Suburban. Did an oil change about a month ago and then changed the spark plugs, but now the car won't even start??? I have no clue now.


When you initially turn on the ignition switch,(before engaging the starter) do you hear a humming sound from the rear of the vehicle for about 3sec's? (sort of like a motor running) If not, you have a bad fuel pump. (The fuel pump is located inside of the fuel tank)

Jan 03, 2011 | 1998 GMC Suburban

1 Answer

Problem for GMC 1998 Suburban DIESEL DIES while


Its called the fuel pump cylinoide which is attached to the fuel pump. Unless the fuel pump is bad, you got an expensive part to buy around $2500 or the cylinoide is $900 whichever is broken. This is a know issue for GMC deisel suburbans 6.5.

May 12, 2010 | 1998 GMC Suburban

1 Answer

ODBII code reader not working on my 98 suburban


IS PIN 16 OF THE OBD2 TEST CONNECTOR HOT WITH 12 VOLTS SHOWING? THIS IS THE BOTTOM ROW OF PINS LAST ROW ON THE RIGHT. GO HERE TO SEE DIAGRAM.

http://westersgarage.eidnet.org/obd2.doc

Mar 17, 2010 | 1998 Chevrolet Suburban

1 Answer

1998 gmc suburban. when i try to start it, it


clean and tighten the battery connections,using a wire brush or wire wool.
Might need to replace starter again..that can happen.

Sep 30, 2009 | 1998 GMC Suburban

1 Answer

Car dies while driving and will not start up


Does it start after cooling down? If so then you have a bad ignition module located in the bottom of the distributor.

Mar 02, 2009 | 1998 GMC Suburban

1 Answer

97 gmc suburban heater fan only works on hi


hello , it is located under right side of instrument panel , on heater housing . an extra clue is the wire connector going to it has a dark blue, a light blue , a tan and a yellow wire on its connector , you will only see the outside of the resistor as the actual resistors ago inside the heater case .and also this is 1997 gmc suburban , even tho listed under 1993 gmc suburban , same instructions . hope ya fix yer problem .

Jan 04, 2009 | 1993 GMC Suburban

2 Answers

Brake lights do not work


This is a well documented problem, replace the turn signal/multifunction switch to correct this issue, this very problem happened on my GMC, it is a 99 as well, replaced the switch as instructed by a chevy forum member and it fixed the problem

Nov 07, 2008 | 1999 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...