Question about Ford Cars & Trucks

Open Question

Head Repair Manual ford ranger 2.5 td

Valve clearance

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
bunnydawg
  • 5158 Answers

SOURCE: Ford Ranger PCV valve.

should be on the valve cover... goes into the cover thru a rubber gromet with a vacuum hose attached.

Robert

Posted on Jan 26, 2009

Ad
davesmith_37
  • 94 Answers

SOURCE: where is the pcv valve located on a 2003 ford ranger

  • The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.
  • Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.
  • Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.
  • Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.
  • Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.
  • When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.
  • Posted on Feb 27, 2009

    • 54 Answers

    SOURCE: Need Valve clearance for '93 kh ford laser

    0.10 - 0.15mm inlet
    0.18 - 0.23mm exhaust
    but you must be carefull because the top of the valve seat becomes concave from wear, a feeler guage will not give the most accurate reading, hope i have been of some hel

    Posted on May 14, 2009

    • 113 Answers

    SOURCE: 2008 FORD RANGER SERVICE MANUAL

    GO TO MITCHELL ON DEMAND ON THE WEB OR THE DEALER. VEH IS TOO NEW FOR A HAYNES MANUAL. YOU MAY HAVE TO BUY THE FACTORY MANUAL, SO BRING YOUR VISA CARD.

    Posted on Aug 25, 2009

    Testimonial: "thanks for the quick reply.i did check mitchell on demand but they only cover us cars,im after an australian version "

    • 34 Answers

    SOURCE: Cyl. head tightening torque and sequence for a

    The online manuals are a super help. I use them all the time. http://www.autozone.com/autozone/myzone/profile/membershipBenefits.jsp

    Posted on Oct 14, 2009

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    Torque settings or 2006 Ford ranger ...for head, main bearings, connecting rod bearing, flywheel and valve clearance


    You should be able to find this information at the library in the non fiction section; most libraries have Chilton's manuals and they are free to use.

    May 02, 2017 | Ford Cars & Trucks

    1 Answer

    2.5 ranger td 2007 diesel pump timing marks n will da key way on the pump should b same as the timing marks


    images for 2.5 ranger td 2007 diesel pump timing marks

    Ford ranger 2.5 diesel pump timing marks - Fixya

    www.fixya.com/.../t12609400-ford_ranger_2_5_diesel_pump_timing_...
    Apr 29, 2012 - SOURCE: need the timing marks for a 3.1 td 5 cyl diesel injectionpump. isusu engine?? have you looked for a 8mm hole in timing gear that ...

    Mazda Bravo 2.5 TD 2000 - YouTube

    ? 10:00
    https://www.youtube.com/watch?v=D8zJeouIXfo
    Sep 11, 2010 - Uploaded by V8Jagnut
    and one other , would a miss timing on the fuel pump cause engine .... The only thing I've ever seen with a Mazda dieselengine was an old Mercury Lynx. ... Ford Ranger Mazda B25002.5TD Servicing Guide Part 2 - Air and .

    Oct 29, 2015 | 2006 Ford Ranger

    1 Answer

    I need to know the fireing order on a 2.8l engine in a 1985 ford ranger


    Tune Up

    Spark Plug

    AWSF-42C

    Spark Plug Gap

    0.044

    Ignition Timing

    10 degrees BTDC

    Firing Order

    1-4-2-5-3-6

    Distributor Rotation

    Clockwise

    Valve Clearance Intake

    0.014

    Valve Clearance Exhaust

    0.016

    Aug 04, 2011 | 1984 Ford Ranger

    1 Answer

    Wat is valve clearance on ford ranger 2002


    If you have a 2.3L engine the tappet to valve clearances are:

    Intake = 0.22 - 0.28 mm (0.008 - 0.011 in)
    Exhaust = 0.27 - 0.33 mm (0.010 - 0.013 in)

    If you have either the 3.0L or 4.0L, there are no adjustments because they use hydraulic lifters.

    Nov 12, 2010 | 2002 Ford Ranger Regular Cab

    1 Answer

    I need to know the valve clearance for a 1985 ford ranger 2.8 liter engine?


    Ford uses hydraulic valve lifters,turn engine over to install rockers,engine oil pressure keeps valves constantly adjusted.

    Oct 12, 2009 | 1985 Ford Ranger

    3 Answers

    Head bolt torque for a 1996 ford ranger 2.3liter


    The torque specs and tightening sequence can be found in Haynes repair manual #36071.Ford Ranger 1993-2005

    Jun 26, 2008 | 1996 Ford Ranger SuperCab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    54 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    76051 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    fordexpert

    Level 3 Expert

    5516 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...