Question about 2002 Isuzu Axiom

Open Question

Service Engine light on TOD light is flashing code P102 P102pd

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: 1999 Isuzu Trooper TOD won't go into 4 whl drive.

look at vsv assembly related posts on this site. Wesley has a great procedure. Works!!

Posted on Jan 02, 2010

c1apton15
  • 3400 Answers

SOURCE: TOD Check light? My check

Have a local shop or auto parts store perform a "Fault Scan" - Most good auto parts stores will do it for you for FREE. They read the codes, print out what is wrong and reset your lights.

Posted on Jan 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why do the Tod 4wh flash and the check light stay on when I driving


some times they tie in another circuit to a check engine light , i have that happen with the emergency brake light on and engine check light

Feb 02, 2015 | 1998 Acura SLX

2 Answers

P102 Code


It actually is saying the air flow is low at the MAF passage. This can mean a clogged air filter or clogged ductwork. Your engine RPM may have changed from the tuneup. If this is the type of engine with the added spout to the distributor, you may have not reconnected it after setting timing.

A bad groundwire will also affect every engine setting overall or from the single badly grounded sensor. You may want to do an Ohm test on the plug-in wires for the MAF to its ECM. You may have a broken wire which would affect the readings.

Just to illustrate, if the MAF produced a fictious 1 volt at normal flow, then the timing and fuel enrichment are set for that RPM. But if the MAF reads .5Volt, it may enrichen the fuel or adjust timing for an engine running 3000RPM. This would flood the converter with more gas than was being burned and needed at idle and result in a Sulfur smell.

Feb 21, 2012 | 2000 Chevrolet Astro

1 Answer

TOD Check light? My check light under the TOD keeps flashing on and off. Please help me what should I do?


Have a local shop or auto parts store perform a "Fault Scan" - Most good auto parts stores will do it for you for FREE. They read the codes, print out what is wrong and reset your lights.

Jan 05, 2011 | 2001 Isuzu Trooper

1 Answer

My check engine light is on but car runs fine code P0102 comes up what could this be


CODE P102 IS MASS AIR FLOW SENSOR VOLUME AIRFLOW SENSOR LOW INPUT.

Jul 19, 2010 | Cars & Trucks

2 Answers

P102 Service Engine light warning came up.


MAP and O2 sensor are two separate items. MAP, reads manifold pressure, O2 reads exhaust content. O2 sensor often is a false reading not to be ignored but should not be immediately changed till other items are corrected. MAP sensor is often mounted on the firewall and can be identified as having an electrical connector and a vacuum hose attached to it. (ask a parts house to show you one and it will make finding it easier) Check for vacuum leaks in the hose and make sure the hose is well connected at both ends before changing the sensor. You may also want to clean the Mass Air Flow sensor located between the air duct hoses running from the air filter box to the throttle body. There are two small wires inside it that can be cleaned carefully with carb cleaner and a Q tip.If dirty, it can cause idle fluctuations or stalling.

Jun 17, 2009 | 2000 Oldsmobile Intrigue

1 Answer

TOD


TOD light blinking means the TOD is sending a fault code. have the dealer check it out.

You can switch from 2WD to TOD-HI, at any speed below 50 MPH.

If you want to switch to TOD-LOW, you have to stop the car, put the transmission in Neutral, then turn the dial to TOD-LOW. When you switch out of LOW, do the same.

Jun 02, 2008 | 2003 Isuzu Axiom

Not finding what you are looking for?
2002 Isuzu Axiom Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...