Question about 2004 Chrysler Sebring

Open Question

Map sensor cleaning - 2004 Chrysler Sebring

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the map sensor on a 2010 ford crown victoria police interceptor?


Understanding Map ,Bap Maf. ' 4.6L Based Powertrains ' Crownvic.net

crownvic.net/ubbthreads/ubbthreads.php?ubb=showflat&Number...

Dec 30, 2011 - 4 posts
FORD: 2003-2005 Crown Victoria, Thunderbird ... BARO is adjusted to a value based on the ESM's MAP sensor reading during key-on prior to engine start. ... pre 2003crown vic p71,3.27 trac loc,quick start,dual flowmasters,air box mod. ... Carlisle 2010, Carlisle 2012, Motor City Madness, 1992 - Up: Aeros ...

Ford Crown Victoria MAP Sensor - Free Shipping - Standard

www.autopartswarehouse.com > MAP Sensor > Ford
Don't want to waste your time and money on a poorly made Ford Crown Victoria MAP Sensor? We have a durable one in stock. Shop now!

how to clean a mass air flow sensor / meter ... - YouTube



Dec 23, 2015 | Ford Cars & Trucks

1 Answer

I have a daewoo nubira 1.6 KLAN and it has just been diagnosed as having faUlt code PO107 manifold pressure sensor low


MAP sensor sending low voltage back to ecu.
possible causes....vacuum leak to sensor, broken wiring, faulty map sensor...can also be blocked with carbon...remove and clean first

DAEWOO NUBIRA 2 0 16V FROM 1997 AIR MANIFOLD PRESSURE MAP SENSOR ULTRA...

Feb 24, 2015 | Daewoo Cars & Trucks

1 Answer

Why is my 2000 odessey van stalling out when its idiling


Try cleaning the map sensor and the mass air flow sensor. Do not use carb cleaner. Use cleaning spray that is safe for MAP and MAS sensors.

Apr 25, 2014 | 2000 Honda Odyssey

1 Answer

2002 jeep map sensor problems


Not exactly sure what you're describing. Incorrect voltage to or from Map sensor? Map sensors are very sensitive. I clean mine with a Map Sensor Spray cleaner every time I change the Air filter. Check to see if the fine, almost hair like wires in the Map sensor are broken...replace and/or clean if necessary. Best of luck resolving this problem.

Mar 31, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Locating MAF on 2001 alreo


Honda's do not use a mass air flow (MAF) sensor. They use a manifold air pressure (MAP) sensor. The MAP sensor measures vacuum vs the MAF sensor measuring air flow/temperature. No real reason to clean a Honda MAP sensor. Are you having engine performance/idle problems? --------------------------------------------------------------------------------
Digimaster 3

Apr 02, 2013 | 2000 Oldsmobile Alero

1 Answer

Stopping at red light the car starts to stutter as I accelerate


Your confusing MAP with a MAF sensor . You can not clean a MAP sensor .
manifold absolute pressure sensor (MAP sensor )
mass air flow sensor MAF you can clean .

admissions = emissions !
accelerate again and it starts to stutter. Try the TPS - throttle position sensor .

May 03, 2017 | 2001 Hyundai Elantra

1 Answer

Where is the MAP sensor on 99 jeep grandcherokee 4.7 L 8 cylinder


On 4.7L the MAP sensor is located on the front of the intake manifold. An O-ring seals the sensor to the intake manifold.

zjlimited_1118.jpg
(click over image for zoom)

  1. Disconnect electrical connector at sensor.
  2. Clean area around MAP sensor.
  3. Remove 2 sensor mounting bolts.
  4. Remove MAP sensor from intake manifold.

Hope this helps.

Apr 27, 2011 | 1999 Jeep Grand Cherokee

1 Answer

How hard is it to replace the MAP sensor on a 2001 dodge durango?


VERY SIMPLE!!!!!

4.7L The MAP sensor is located on the front of the intake manifold. An O-ring seals the sensor to the intake manifold.
  1. Disconnect electrical connector at sensor.
  2. Clean area around MAP sensor.
  3. Remove 2 sensor mounting bolts.
  4. Remove MAP sensor from intake manifold.
To Install:
  1. Clean MAP sensor mounting hole at intake manifold.
  2. Check MAP sensor O-ring seal for cuts or tears.
  3. Position sensor into manifold.
  4. Install MAP sensor mounting bolts (screws). Tighten screws to 3 Nm (25 inch lbs..) torque.
  5. Connect electrical connector.

Apr 23, 2010 | 2001 Dodge Durango

1 Answer

1993 dodge stealth trouble code 14 & 41, car does not start


Code 14 is a faulty MAP sensor , and 41 is alternator field control circuit open or shorted. I'd start with checking and cleaning the connector at MAP sensor, and check all connection at alternator as well as battery. You'll need to replace MAP sensor and have alternator tested if cleaning doesn't cure it.

Mar 06, 2010 | 1993 Dodge Stealth

1 Answer

Jimmey 4x4 1996 replace map sensor 2 times code still gos off and loses power i relace air filter clean carb if i clean sensor it will work for 2 to 3 days


CHECK MAP SENSOR HOSE FOR VACUUM IT NEEDS VACUUM TO WORK RIGHT. ALSO CHECK THE ELECTRICAL CONNECTOR TO MAP SENSOR.MAKE SURE ITS INTACT.YOU COULD HAVE AIR VACUUM LEAK AT INTAKE MANIFOLD OR PLENUM.OR THE EGR SYSTEM NOT FUNCTIONING PROPERLY.

Oct 11, 2009 | 1996 GMC Jimmy

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...