Question about 2006 Chevrolet HHR

1 Answer

U2011 power steering lost comunication whit the BCM

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Chevrolet Master
  • 1,207 Answers

U2011 Module Transmitted Invalid Data (Non SCP), hope it can help you.
VAS 5054A best quality version

Posted on May 02, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2003 Buick century lost key trying to figure out how to hotwire

With out a key how are you going to unlock steering ?
The steering column lock !
Beside that you would have to get around anti-theft system ! An the fact that all functions on your vehicle are controlled by computers ! The ignition is an input to the BCM - body control module !
Serial Data Power Mode
On vehicles that have several control modules connected by serial data circuits, one module is the power mode master (PMM). On this vehicle the PMM is the Body Control Module (BCM). The BCM receives 4 signals/circuits from the ignition switch. These are the Ignition 0, Ignition 1, Crank and Accessory 1 ignition switch signals/circuits.
To determine the correct power mode the BCM uses:
• The state of these signals/circuits, either switch closed (B+ = 1) or switch open (open = 0)
• The sequence of switch closures received by the BCM
• The status of the engine run flag.
I'd say you don't have a snow balls chance in guam of hot wiring this vehicle ! There made so that can't be do ! So have it towed to a GM dealer or some other qualified repair shop ! Because if you start jumping wires you'll burnt of computers etc....

Aug 21, 2016 | Buick Cars & Trucks

2 Answers

How much to replace power steering fuse on a chevy maiulb

Wrench light means you have a fault or service is due. Not sure what fault is . If it is a fuse the part cost is small, not sure about labour cost, it depends on where fuse is located but shouldn't take more than a few minutes. Hope this helps

Mar 04, 2016 | 2004 Chevrolet Chevrolet Malibu LT

2 Answers


You vehicle has two fuse's ! one in the underhood fuse box EPS/STR WHLCNTRL an it is a 60 amp . An there is one in the BCM fuse center - EPS 2amp fuse ! do you know what an where the BCM is ? The BCM - body control module !
Body Control Module (BCM) location
Under the I/P below the radio on the right side of the center console .19
Electronic Power Steering (EPS) Column Assembly and Inflatable Restraint Steering Wheel Module Coil

Aug 05, 2015 | 2006 Chevrolet HHR

1 Answer

No power to right side of bcm, Green plug

ck all fuses whit test light

Oct 21, 2014 | Cars & Trucks

1 Answer

Loss of power steering and eps light coming on ,on vauxhall meriva 2006.

Whenever this warning light or any other stays on in the dash it is indicating that the systems control module (or the system sensor in the case of lights like low oil pressure, door open indicators etc.) has detected a fault, it then disables the system (this applies to ABS,TCS, TCM, SRS and BCM faults and others) as long as the light is on. You must now have the dealer hook up a special electronic diagnostic tool and "scan" the system for the fault code that is stored for the problem(s)

Legend of Abbreviations. ABS Antilock brake system.TCS Traction control system, TCM Transmission control module, SRS Supplemental restraint system, BCM Body control module

Oct 16, 2012 | Vauxhall Cars & Trucks

2 Answers

Range rover l322 2002 heavy power steering renewed

The Solenoid fitted on the Steering Rack is not getting the command from The Body Control Unit. Kindly Replace your BCM and then your problem is solved. You can try to make sure by giving direct current of 12v to the solenoid and check the Steering. if it works then simply change the BCM as it's not giving d command to the Solenoid. Salman EiD

May 15, 2010 | 2005 Land Rover Range Rover

1 Answer

Camaro 1995 v6 3.4 dont move whit the key in star position,all light ok,battery new, stater new all allrelay news,where are in the car the theft deterrent module?,this car have the antitheft sistem. ...

The theft system is controlled by the BCM (body control module), located behind the glovebox. BCM codes and igniton key module codes must match. Did you have make sure the code generated by the key is a match for the BCM , if not the car will not start. Pellet in key is a resister that has to match the resister setting in the BCM. It is not the keyway module that starts the car,,it is the BCM.

Jun 03, 2017 | 1995 Chevrolet Camaro

Not finding what you are looking for?
2006 Chevrolet HHR Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

80637 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides