Question about 2000 Subaru Outback

Open Question

Transmission pan bolt torque

I just want to know what torque to set too

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: what is the torque on the transmission pan bolts

8 to 12 Nm

Posted on Aug 12, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I have a 00 Bmw 323ci I just put a new used transmission in it I got a new filter and gasket for the transmission but I need to know what's the torque for the bolts when putting the pan back on


on transmission and oil pans i normally torque them to where you can see the gasket compressed to where its starting to fill the gap between the pan and the trans and i've never had a leak yet

Oct 06, 2015 | BMW Cars & Trucks

1 Answer

Bad transmission seal on a 2002 ford explorer


Drain the Transmission Fluid and Replace the Filter
Raise the car with ramps or a floor jack and support it with jack stands. Find the lower cover of the torque converter housing. Turn the torque converter until you find the drain plug. Place a drain pan beneath the drain hole, remove the plug and drain the fluid.
Remove the cooler lines at the transmission and flush them with compressed, low pressure air. Be careful during this step; fluid may shoot from the other cooler line.
Place a large drain pan beneath the transmission. Loosen the retaining bolts on the oil pan with a socket wrench until they are within a few turns of removal. If the seal doesn't break on its own, gently tap it with a rubber hammer. Fluid will drain from the edges of the pan.
Remove the pan retaining bolts when the fluid stops draining. There is still transmission fluid in the pan. Hold the pan carefully and drain as much as you can into the drain pan.
Scape the old gasket material from the mating surfaces on the oil pan and the transmission. Discard the old gasket. Clean the magnet in the pan. Clean the pan and the mating surfaces with a solvent and a clean, lint-free cloth. Replace the magnet and allow the pan to air dry.
Employ a socket wrench to remove the bolt that holds the filter onto the transmission. Some models may have two bolts. Pull the filter and any old seals or gaskets from the transmission. Install a new filter assembly, including any required seals or gaskets.
Put a new gasket on the oil pan and reinstall it on the transmission. Tighten the retaining bolts to 79- to 119-inch pounds with a torque wrench. Replace the cooler lines on the transmission and the drain plug on the torque converter.
OBD Tools 365 Days Shop

Sep 25, 2014 | 2002 Ford Explorer

2 Answers

Leaks transmission oil f


Check transmission pan & lines 4 leak. Tighten all pan bolts, line connectors & drain plug. U may need a new transmission pan gasket. Any cracks in transmission?

Jan 05, 2011 | Nissan Maxima Cars & Trucks

1 Answer

I need to know he torque spects for the oil filter container the bolts on to the moter on a 94 BMW 318i...there are 6 bolts...I also need to know the torque spects on the alternator mounting bracket...


OIL PAN OR TRANSMISSION PAN BOLTS TORQUE ABOUT 7 FT LBS. CAN GET SPECS ON BOLTS SIZES. IF BOLTS SIZES IS 13M I4M 15 M TORQUE BOLTS ABOUT 55 TO 80 FT LBS

Nov 11, 2010 | 1994 BMW 3 Series

1 Answer

Is the Transmission sealed, can not change the filter and fluid? Where is the radiator, is it also sealed, can water only be put in the overflow?


The transmission is not sealed in the v8 I looked up. It's bolted together. prev.gif next.gif Fluid Pan Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section
  2. Raise and support the vehicle
  3. Place a drain pan under the transmission fluid pan
  4. Remove or disconnect the following:
    • Drain plug and drain the fluid
    • Shifter cable bracket NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
    • Fluid pan and gasket
    • Transmission fluid filter
    • Clean and inspect the transmission fluid pan and magnet
    • Converter housing access plug
    • Converter drain plug
To Install:
NOTE: A new converter drain plug must be used to prevent leakage.
  1. Install or connect the following:
    • Install the converter drain plug. Torque to 89 in-lbs (10 Nm)
    • Install the converter housing access plug
  2. Lubricate the seals and install the transmission fluid filter. Torque the bolts to 89 in-lbs (10 Nm)
  3. Install the oil pan magnet in the transmission fluid pan NOTE: The transmission fluid pan gasket is reusable, clean and inspect for damage; if not damaged, the gasket should be reused.
  4. Install the transmission fluid pan and gasket and loosely install the screws.
  5. Using a crisscross sequence, torque the screws to 8 ft-lbs (11 Nm)
  6. Install the shifter cable bracket. Torque bolts to 18 ft-lbs (25 Nm)
  7. Install the drain plug. Torque to 19 ft-lbs (26 Nm) NOTE: It will be necessary to hold the drain plug (larger plug) with a wrench when removing the fluid level indicator plug.
    NOTE: Use 3/16 inch Allen key to remove the fluid level indicator plug. Remove the fluid level indicator plug.
  8. Verify the transmission fluid level
prev.gif next.gif

Jul 21, 2010 | 2001 Lincoln LS

1 Answer

How to remove oil pan on kia sportage 99? thanks,Zak.


Hi Zak:
Kia Sportage 1998-02 Repair Guide
Oil Pan - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:

    Negative battery cable 2 Top intake manifold bracket bolts Front 3 axle housing mounting bolts, 4WD only Left front bushing from the axle housing mount and lower the front axle housing Both gusset plates from the engine Transmission under cover Engine under cover Oil pan mounting bolts and using a scrapper tool separate the oil pan Oil pan Oil strainer assembly Oil baffle 76b1888.jpg


  4. Fig. Exploded view of the oil pan assembly mounting

To install:


f149924.jpg
Fig. Tighten the oil pan bolts in sequence
  1. Clean the engine block, oil pan and baffle pan surfaces of any gasket material.
  2. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the baffle pan.
  3. Install or connect the following:

    Oil baffle. Torque the bolt to 84 inch lbs. (9.5 Nm). Oil strainer. Torque the bolts to 84 inch lbs. (9.5 Nm).
  4. Apply a continuous bead of Loctite Ultra Blue 587® silicone sealant around the oil pan.

    Oil pan. Torque the bolts to 84 inch lbs. (9.5 Nm). Transmission under cover. Torque the bolts to 84 inch lbs. (9.5 Nm). Gusset plates to the engine. Torque the bolts to 33 ft. lbs. (45 Nm). Engine under cover Front axle housing into position. When properly aligned, torque the bolts to 48 ft. lbs. (65 Nm). Intake manifold bracket bolts. Torque the bolts to 34 ft. lbs. (65 Nm). Negative battery cable
  5. Fill the engine with clean oil.
  6. Start the vehicle and check for leaks, repair if necessary.

Hope helps with this (remember rated this) Good luck.

Jan 12, 2010 | 1999 Kia Sportage

1 Answer

Oil and transmission pan bolt torque specs


124 inch lbs on oil pan...Transmission pan 13 ft lbs.

May 06, 2009 | 1991 Buick Park Avenue

1 Answer

Torque settings on a 1999


There are 2 different tranmissions in this vehicle. Make sure you know which one you have when selecting the torque settings. Do notice the 5R55E pan bolts are tightened in inch pounds. 4R70W Torque convert drain plug. 21-22 ftlb Pan bolts 9-11 ftlb 5R55E Pan bolts 115-133 inlb Ford Rear end Pan bolts 33 ftlb

Apr 05, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
2000 Subaru Outback Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...