Question about 1998 Lincoln Navigator

1 Answer

Instrument cluster gauges not working 1998 navigator

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Lincoln Master
  • 15,691 Answers

Replace the whole instrument cluster.

Posted on May 02, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel gauge fuse on a 1998 Buick Century?


There is not a single fuse for the fuel gauge , there are a few that power up the whole instrument cluster ! If there were a fuse out more then just your fuel gauge wouldn't work .You probably have a bad sending unit in the fuel tank or the stepper motor for that gauge is bad ! The thing to do would be to take to the dealer or some other capable ASE certified repair shop that has a up scale scan tool that can check codes in the instrument cluster ! Or you can take a chance an replace the instrument cluster !
Fuel Gage Inaccurate or Inoperative
Inspect for any stored instrument cluster Diagnostic Trouble Codes (DTCs). Are any DTCs stored in memory?
--
Go to Diagnostic Trouble Code (DTC) List/Type
Go to Step 3

3

  1. Install a Scan Tool scan tool.
  2. Turn the ignition switch to the RUN position.
  3. Establish communication with the instrument cluster.
  4. Select special functions under the main menu.
  5. Select output control under special functions.
  6. Select fuel gauge sweep test under output control main menu.
Does the fuel gauge perform a full sweep when commanded?
--
Go to Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.1L
or
Powertrain On Board Diagnostic (OBD) System Check in Engine Controls - 3.8L
Go to Step 4

May 23, 2015 | 1998 Buick Century

1 Answer

Instrument cluster


Duplicate question.

May 01, 2013 | 1998 Lincoln Navigator

2 Answers

LINCOLN NAVIGATOR


Could be the gauge in the dash, the temp sensor on the engine, or the thermostat is not closing to warm up the engine.

Sep 17, 2012 | 1998 Lincoln Navigator

1 Answer

Gauges in my 1998 plymouth neon stopped working when i hit a bump


Sounds like an intermittent loss of power to the instrument cluster to me. Remove the instrument cluster and inspect the electrical connectors on the back of the cluster.

May 28, 2012 | 1998 Plymouth Neon

2 Answers

1998 chrysler t & c van. can start the van drive it, then gauges stop, suddenly sometimes


The problem is your instrument cluster. Your type of vehicle is notorious for the instrument cluster failing. It will need replaced, or rebuilt.

Sep 02, 2011 | 1998 Chrysler Town & Country

1 Answer

The gauge fuel and odometer no work


elinmorta16: Is this problem intermittent, did it come on progressively, getting worse each time, or has it been resolved? I'm assuming it's a 1998 Voyager. I would first and foremost suspect the instrument cluster main harness solder joints. I had a similar problem that eventually caused vehicle to fail to start altogether. After reviewing several posts about it I decided to re-solder all these joints. This didn't initially resolve the no start problem ---- UNTIL ---- I did the instrument cluster self-diagnosis test. With ignition off, hold the trip meter and reset buttons for 10 or more seconds. When I turned the ignition to on, I got the self check sequence displaying on the odometer. After it completed, my dash gauges worked just fine......and the vehicle started again!!

To find the instrument cluster fix, google "1998 voyager instrument cluster solder". You should find several posts explaining it. It eventually worked for me!! God bless those who take the time to help others!

Aug 01, 2011 | 1998 Plymouth Voyager

1 Answer

98 Town Car, how do I change dash lights, (fuel gauge bulb)


  1. Disconnect the negative battery cable.
  2. Remove the instrument cluster.
  3. Remove the retaining screws for the instrument cluster lens and cover assembly. Remove the cover and lens.
  4. Remove the retaining screws for the gauge or warning lamp to be replaced and remove the gauge or warning lamp. To install:
  5. Place the gauge or warning lamp into place and tighten the retaining screws.
  6. Install the instrument cluster lens and cover assembly.
  7. Install the instrument cluster.
  8. Connect the negative battery cable.

Feb 04, 2011 | 1998 Lincoln Town Car

1 Answer

The gauges don't work


The instrument cluster operates independantly of the lighting for them. You could possibly have a fuse somewhere that has blown causing all gauges to stop, or it could potentially be that the cluster itself is bad and needs replaced or this could be a sign of a wireing harness failure of the instrument cluster. I'm afraid your best bet is to take it in and have it looked at by someone trained in dealing with those parts of the system.

Apr 14, 2009 | 1998 Chevrolet Malibu

1 Answer

Gas gauge no longer works


The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures.
Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install
Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors
NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel.
Remove the instrument cluster from the vehicle.
Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.)
when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks

May 14, 2008 | 2007 Jeep Scout

Not finding what you are looking for?
1998 Lincoln Navigator Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

fordexpert

Level 3 Expert

5520 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...