Question about Cars & Trucks

Open Question

Vz commodore LS1

Open Question To john gee- oil sensor has 3 wires however has been replaced (a/c delco ) still goes in limpmode replaced 02 sensors and fuel filter (95% blocked) replaced pcm and fbw throttlebody and 8 wire plug to the throttlebody still have random limpmode l turn engine off for 10 seconds/restart engine and all is good again there are no error codes via tech 2 scanner checked every possible sensor/ everything and no error codes what else to look for any ideas john

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5370 Answers

SOURCE: ihave a 2001 pontiac grand

May be the injectors are dirty.The fuel injectors,if they are clogged and blocking the fuel to flow or they are cracked or dirty then can cause such problems.Clean the injectors,if they are worn out cracked then replace the injectors.But if injectors checked out ok then yes crank shaft position sensor ,if its faulty or weak it can cause this problem.For more troubleshooting on this problem.Click the link below:---http://technoanswers.blogspot.com/2011/01/random-misfire-code-gets-set-on-car.html
--------- This should help.Thanks.Helpmech.

Posted on Jan 30, 2011

Ad

SOURCE: faulty oil pressure sensor [ ls1 ] australia

Hi Grumpy, If there is one single cable connected to the Oil Pressure Sensor it is usually a direct connection to the instrument panel light. Basically it's a make and break pressure switch. If there more than one cable it will probably be controlled via the computer and therefore you'll need to replace it. Let me know more details? Regards John

Posted on Mar 24, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will ls1 go in vx commodore s 2000


yes VX V8s were fitted
depends on what state you live in
LS1 fitted may need a modification plate
needs the LS1 engine ecu and
and a few extra wiring and
join the just commodore forum for loads of helpful information
http://forums.justcommodores.com.au/vt-vx-holden-commodore-1997-2002

Jul 29, 2016 | Cars & Trucks

1 Answer

Ford c max goes in limpmode dpf blocked fitted dpf egr and dpf presser sensor sill goes in limpmode


Requires fault codes to be reset, this will require a code.reader with your models software.

Jul 05, 2016 | 2007 Ford C-MAX 1.6

1 Answer

Hi could you help with replacing an oil pump on a 3.6 vz holden cruiseman


I would go to the Just Commodores Forum for that and one of the guys there should be able to help with the pump issue if you supply all the details. here is the link to the VZ Forum section.............
Forum VZ Holden Commodore 2004 2006


======================================================

May 08, 2016 | Holden Cars & Trucks

1 Answer

What causes svs occasionally appear on dash on vzss holden commodore ls1 5.7 [aus] ?


If you mean its the "service" indicator its possible the exhaust sensor is telling the engine it is running incorrectly, fuel mixture wise. This is usually carried out by a Lambda unit in the headers. It may be rectified by an engine service but get someone to plug in a fault reader to get a better idea.

Jul 03, 2014 | 2006 Holden Commodore SS

1 Answer

Commodore 5.7 australia has limpmode [engine only] had car checked 19/9/2013 by the horse power factory.Every single electrical part on this car was checked/ecu right through to the rear of car,all sensors...


When the cpu sends the engine into limp mode it has found a sensor that is outside the set parameters. . Next point is that unless you replaced all sensors with OEM equipment or the cpu with a genuine OEM cpu then it is possible that the parameters of the sensors are not properly recognised by the cpu. If it happens at running temperature. Then I would be suspicious of an temperature sensor (water-ambient - oil etc) that is set at parameters limit. It does not necessarily mean that a fault code will be stored but it may be tipping the cpu into limp mode. Checking all connectors for a loose/broken wire in the connector may be a place to start.

Sep 20, 2013 | Cars & Trucks

1 Answer

Faulty oil pressure sensor [ ls1 ] australia


Hi Grumpy, If there is one single cable connected to the Oil Pressure Sensor it is usually a direct connection to the instrument panel light. Basically it's a make and break pressure switch. If there more than one cable it will probably be controlled via the computer and therefore you'll need to replace it. Let me know more details? Regards John

Mar 24, 2013 | Cars & Trucks

1 Answer

Safety mode issues on holden commodore gen111 australia


I had the same problem with my VZ holden couldn't solve the problem said it was the o2 sensor turned out they have had a big problem with the fuel solenoid got it replaced and have not had a problem since had to wait for a part to come from overseas they had none left in stock. The car used to not start after running and start shuddering with the check powertrain warning.

Feb 18, 2013 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...