Question about Cars & Trucks

Open Question

Replace rear brake shoes on ford bantam bakkie model 2006

How to remove the brakedrum

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 66 Answers

SOURCE: Ford Focus Brake shoes

You need to remove the axle nuts to get the drums off. Left side may have left hand treads.

Posted on Jan 04, 2009

Ad
  • 8 Answers

SOURCE: how to change rear brake shoes on a 2004 chevy venture

The rear brake shoes use a U clip to hold the shoes together. A simple solution to this change job is to change one side at a time.
Slowly unclip the U clip from the top of the shoe and remove the left shoe and spring. Replace the left shoe and reconnect the U clip, then do the same for the other shoe. Clean, adjust,and grease the self adjuster and you're done. Do the same for the other side of the van. If you take both sides of the clip off you're in for some heavy duty stretching with pliers unless you have the right tool.

Posted on May 12, 2009

  • 111 Answers

SOURCE: replacing rear brake shoes on 2007 silverado 4WD

when you pull the hub off take a picture of the brakes so you can see all the parts, so you can tell where everthing goes back together.

Posted on Feb 14, 2010

techbuster
  • 5081 Answers

SOURCE: 1997 Ford contour rear brake

Brake shoe removel:

Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Posted on Jul 17, 2010

    • 1 Answer

    SOURCE: 2006 chevy colorado install brake shoes

    how do you replace brake pads

    Posted on Oct 10, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    I am looking for a new engine


    We have no parts resources of any kind, but that said you can try auto salvage yards, there are hundreds all over the USA. Just do a used part search and lots will pop up in the search results.

    Aug 30, 2016 | 2006 Ford Bantam 1.6i

    1 Answer

    Can l kindly have a diagram on how to replace brake shoes on a ford bantam rocam 1.3


    Cannot help you here as never seen a bantam but as its a ford i would assume its the same as a ford escort or fiesta ,their not difficult trust me the foreward leading shoe has a leading edge the leading shoe is the thicker one going to the front of the car.the handbrake cable fits to the trailing shoe the one with the arm on for the cable ,the auto adjuster fits just below the slave cylinder with the adjuster to the right or rear of the car smaller spring to the lower and spring with the two coils either end to the top some have a snail cam adjuster some have a little wheel depends on the age of the vehicle ,yes its fiddly but its not a difficult job

    Jul 26, 2014 | Cars & Trucks

    1 Answer

    Ford 1 3 rocam engine


    bantam?
    most cars, MPI injection the injector form a sandwich.
    between the fuel rail, and the intake front tunnel tubes.
    so remove the rail,
    step s
    remove battery neg lug, so some, odd person dont try to start car.
    depressurize the fuel system per FSM.
    then remove injector conn plugs.
    the unbolt rail. bingo.

    the FSM covers this, ask ford parts counter for this book.

    The Ford Bantam is a coupe utility vehicle ("bakkie", "pickup", or "ute") produced by the Ford Motor Company in South Africa. It spanned into three different models and was produced in South Africa for the local market.

    be safe.

    Jul 09, 2014 | 2005 Ford Bantam 1.6i

    1 Answer

    Can't get the rear brakedrum off


    emergency brakes not engaged, right ? Look for small access hole on rear plate, theres a little toothed wheel there you can turn down with a small screwdriver to adjust shoes, keep turning it till pressure off shoes

    Apr 08, 2014 | 2002 Jeep Liberty

    1 Answer

    Ford bantam diesel bakkie 2004


    check the vaccuum pipe to the brake booster ,sounds like the booster is not receiving vacuum to power assist your brakes

    Jan 15, 2014 | Cars & Trucks

    2 Answers

    How to bleed n Clutch system on Ford Bantam 1.3


    I have a Ford Bantam 1.3 bakkie and the clutch fluid is running / leaking into the vehicle itself. How do we replace?

    May 03, 2012 | 2006 Ford Bantam 1.3i

    2 Answers

    1997 Ford contour rear brake shoe replacment help.


    Brake shoe removel:

    Depress and turn the retainers for the hold-down springs and pins to remove them from each shoe. Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.

    Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.

    Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

    Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xgUqun
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xdByQ8

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

  • Step 2 Slide the brake shoe assembly--including the shoes and springs--down so you can disengage the top ends of the shoes from the cylinder and tilt them to lift them past the retaining plate.
  • Step 3 Unhook the lower retracting spring from the front brake shoe to disconnect it. Spread the shoes apart at the bottom to remove the adjusting screw, the screw's retracting spring and the adjuster lever. Remove the front brake shoe.
  • Step 4 Pull the parking brake cable spring back with diagonal cutting pliers, grip the cable with the pliers without cutting it, unhook the cable from the parking brake lever and remove the rear brake shoe with the lever.
  • Step 5 Disconnect the parking brake lever from the rear shoe by spreading the retaining clip with a screwdriver and removing the clip and its spring washer.

  • Read more: How to Change Rear Brakes on a 1997 Ford Taurus | eHow.com http://www.ehow.com/how_6123373_change-brakes-1997-ford-taurus.html#ixzz0u2xVyUAt

    Jul 17, 2010 | 1995 Ford Contour

    1 Answer

    Ford bantam handbrake adjustment


    remove the back brake drums ,slacken handbrake cable then run a mini grinder around the lip on the edge of the drum .Then adjust the auto adjusters manully so when the drum is push on it just goes on ,tap with a hammer all around the drum to level the shoes and if need be adjust up a bit more ,then when finished re-adjust the cable so you have three notches on handbrake lever

    May 31, 2010 | 2006 Ford Focus

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    621 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76682 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...