Question about Mitsubishi Lancer

Open Question

1996 mitsubishi lancer firing order

I recently purchased a set of ignition leads for my 1996 mitsubishi lancer but forgot to mark the connections for the firing order. can anyone please help?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: need engine specs for mitsubishi pajero 1996 3.5 lt 24 valve dohc

ed904ac.gif
Here ya go....get the rest of the info right now.

Posted on Mar 26, 2009

  • 36 Answers

SOURCE: firing order for toyota camry v6 1996

the firing order is in fact 1 2 3 4 5 6 the number one cylynder is on the left at the back, as you look at the engine from the front >>
positions of cylinders
-------------
1 3 5

2 4 6
------------

Posted on Mar 15, 2010

  • 510 Answers

SOURCE: Timing marks setting Hyundai Lantra

Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Posted on Mar 21, 2010

  • 3640 Answers

SOURCE: need the firing order including coil pack to

1995 Land Rover Range Rover SE
4.0 liter V-8 VIN "2"62517654.gif

Posted on May 14, 2010

ZJLimited
  • 17970 Answers

SOURCE: firing order

2003 Mitsubishi Lancer 2.0 liter SOHC L4
and
2003 Mitsubishi Lancer Evolution 2.0 liter DOHC Turbo L4

aebcb80.gif

Hope helps.

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What's the firing order of a Mitsubishi 6g74 engine v6 right hand drive ?


If dizzy is still in place and leads are connected.
Remove dizzy cap and get someone to give starter short kick with ig key making sure hands are clear of moving partsand not touching leads. if rotor button goes clockwise then set to top dead centre with timing mark on pulley rotor button should point to no. 1 so by following plugs you can work out firing order. heads usually have cylinders numbered .

Feb 26, 2017 | Mitsubishi Cars & Trucks

1 Answer

What is the firing order for a 2.4L dohc?


Firing Orders - AutoZone

www.autozone.com/.../Firing-Orders/Firing-Orders/_/P-0996b...
AutoZoneClick image to see an enlarged view ... 2.4L (4G64) DOHC engine with distributorless ignition Firing order: 1-3-4-2 Distributorless ignition system ... Mitsubishi 1996-97 3.0L (6G72) SOHC Engines Firing order: 1-2-3-4-5-6 Distributor rotation: ...Missing: blazer

Sep 30, 2015 | 1996 Chevrolet Blazer

1 Answer

I have a Mitsubishi lancer 2000 and have taken the wires off the distributor in order to change the spark plug leads without concern of how to put them back on. Any ideas on the order


4 cylinder, firing order normally 1342. Take off distributer cap, set engine with number 1 cylinder on top of compression stroke. you may have to take out the number one plug, turn moter by hand and feel for compression with finger on hole. Look where distributer rotor is pointing and match with distributer cap. That will give you #1 lead position. Follow around cap in rotor direction and you will get the rest.
6 cylinder normally 123456. same story.
if you still have the old leads, they are sometimes marked and normally different lengths. if you lucky, and replace them, you can sometimes pick up which went where by the bends left in them over time. Then start again and mark them. I normally replace leads one at a time. Safer and easier. Or Photograph them with cell.

Oct 06, 2013 | 1988 Oldsmobile Delta 88

2 Answers

What is the firing order on a lancer


2002 Mitsubishi Lancer LS 2.0 liter SOHC L4

zjlimited_730.gif

Hope helps.

Sep 22, 2011 | 2002 Mitsubishi Lancer

1 Answer

I want to know the distributor cap firing order along with the firing order on the engine


The ignition order for my 1988 Mitsubishi Mirage is Longest lead to left-hand outer piston, then left-hand inner piston followed by right-hand outer piston then right-hand inner piston., going in an anti-clockwise direction.

Oct 19, 2010 | 1988 Mitsubishi Mirage

1 Answer

Firing order


2003 Mitsubishi Lancer 2.0 liter SOHC L4
and
2003 Mitsubishi Lancer Evolution 2.0 liter DOHC Turbo L4

aebcb80.gif

Hope helps.

Jul 31, 2010 | 2002 Mitsubishi Lancer

1 Answer

Cd5a ignition troubles


if one of the plugs is fouled neither plug will fire

Mar 25, 2010 | Mitsubishi Lancer Cars & Trucks

1 Answer

Distributer question


Your firing order is 1-3-4-2 Your engine cylinder from the passenger to driver's side is 4-3-2-1 Your distributor rotates counter clock wise and #1 is the first post.
Unfortunately Mitsubishi make provisions for checking and adjusting the ignition timing with the use of a scan tool. Most shops do have a scan tool that can be used to check and adjust the ignition timing. sorry friend

Jul 11, 2009 | 1997 Mitsubishi Galant

1 Answer

Need firing order diagram.. wont start


remove the dizzy cap, crank motor over to find out the rotation of the rotor. Remove the no.1 spark plug and bring no.1 piston up to top dead centre on compression stroke, mark side of dizzy body where the end of the rotor points to, replace dizzy cap and see which lead it lines up with.
that will be your no.1 lead, find the firing order and put the leads back on the dizzy cap in the direction of the rotors rotation, run those leads to the corresponding plugs and it should start.

May 19, 2009 | 1979 Lincoln Mark V

1 Answer

What is the ignition firing order


2004 Mitsubishi 2.0 liter SOHC L4

641dea7.gif

Apr 10, 2009 | 2004 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...