Question about Cars & Trucks

Open Question

Replace ignition switch Chevy 2500 HD 6.0 - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 120 Answers

SOURCE: replacing pcv valve

driver side valve cover in the back of the cover. if it even has one, sometimes the cover has been replaced with a later style that uses a baffle instead of a pcv

Posted on Jul 24, 2009

Mike258
  • 1498 Answers

SOURCE: how do you change a lock n key ignition switch on 1998 chevy 6 cy

STOP. STOP. STOP.
I WILL POST WITHIN THE HOUR.
In the meantime, click here for a few things you need to know before even considering working with undeployed airbags.

Mike

Posted on Nov 04, 2009

  • 2309 Answers

SOURCE: Drain Engine Coolant in 2005 Chevy Silverado 2500 HD

there is a petcock at the bottom of the rad drain ti from there and use a antifreeze tester to check protection temp

Posted on Nov 18, 2009

greg_margo
  • 1959 Answers

SOURCE: how about advise on a 2003 chevy silverado 2500 hd

The instructions are below. Also, there will be a diagram for the routing.

  1. Before you begin, visually confirm the belt routing to the engine compartment label (if present) or to the appropriate diagram in this section (if the label is not present). If you cannot make a match (perhaps it is not the original motor for this vehicle), scribble your own diagram before proceeding.
  2. Disconnect the negative battery cable for safety.
  3. Install the appropriate sized breaker bar, wrench, or socket to the tensioner arm or pulley, as applicable.
  4. Rotate the tensioner to the left (counterclockwise) and slip the belt from the tensioner pulley.
  5. Once the belt is free from the tensioner, CAREFULLY rotate the tensioner back into position. DO NOT allow the tensioner to suddenly snap into place or damage could occur to the assembly.
  6. Slip the belt from the remaining pulleys (this can get difficult is there is little room between the radiator/fan assembly and the accessory pulleys. Work slowly and be patient.
  7. Once the belt is free, remove it from the engine compartment.
To install:
  1. Route the belt over all the pulleys except the water pump and/or the tensioner. Refer to the routing illustration that you identified as a match before beginning.
  2. Rotate the tensioner pulley to the left (counterclockwise) and hold it while you finish slipping the belt into position. Slowly allow the tensioner into contact with the belt.
  3. Check to see if the correct V-groove tracking is around each pulley.
7927c2f.jpg

Posted on Feb 02, 2010

  • 2 Answers

SOURCE: How to replace a Thermastat on a 2003 Chevy

The thermostat is located in the water pump on mostn never Chevy trucks. If you pull the upper fan shroud, you should see the thermostat housing. Remove the radiator hose, then the 2 bolts for the housing. Replace the thermostat, and gasket together.

Posted on Feb 17, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 chevy Silverado 2500 HD inertia switch


Your Chevy doesn't have a inertia fuel cut off switch , Ford's do , not GM .

Jan 13, 2017 | 2002 Chevrolet Silverado 2500HD

1 Answer

HOW TO REPLACE THE IGNITION SWITCH ON A 2005 CHEVY 2500 HD


why double post. its back up one.
or add to it, dont make new posts same topic.
thanks

May 04, 2014 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer

What's your problem?back up lights on a 2002 chevy silverado 2500 HD doesn't work, i have checked the bulbs and fuses, they are good ,,, how do i fix them?


disconect the reverse light switch wires from the gearbox & bridge. If the lights come on it is a faulty switch.

Oct 12, 2012 | Cars & Trucks

1 Answer

Repair steering column on 2006 Chevy silverado 2500 hd


The steering wheel has to be removed and further troubleshooting to replace or replace the column or wheel can be performed.For complete step b step procedure.Click the link below :----http://technoanswers.blogspot.in/2012/02/chevy-silverado-2500-hd-steering-wheel.html
-----------This will help.Thanks.

Feb 08, 2012 | 2000 Chevrolet 2500

1 Answer

Replace Ignition Switch Support 89 chevy


I am unaware of what you are refering to with "ignition switch support".
The ignition switch is attached to the steering column near the bottom (close to the firewall). Its held on by two screws (the dimmer switch is also attached to a screw and the ignition switch). The bracket on the ignition switch is part of the switch.

Oct 08, 2011 | 1989 Chevrolet C/K 2500

1 Answer

2003 gmc 2500 hd turn key nothing happends


try checking your neutral safety switch.

Apr 15, 2009 | 2003 GMC Sierra 2500HD

1 Answer

Where is the location of the knock sensor for a 2005 HD 2500 6.0


HAS TWO KNOCK SENSORS they are both under intake in valley of engine. remove intake and will see two black grommets they are under those best to replace both at same time

Jan 26, 2009 | 2000 Chevrolet 2500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...