Question about 2005 Mazda 3 Sedan

Open Question

License plate lights not working mazda 3

Tried replacing bulb and checked fuse. Fuse is fine and new bulb didn't work. Any suggestions?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Mazda 3 (2006) Information Display panel is blank

I took it to the dealer. They fixed under waranty. The new issue is the flash and beep confirmation upon double locking the doors no longer works.

Posted on Jun 05, 2009

Ad
  • 1 Answer

SOURCE: Tail light Works - Brake light does not

My break lights work the reverse lights do not. Is it the neutral safty switch/back up-light switch

Posted on Jun 08, 2009

  • 436 Answers

SOURCE: mazda 3 passenger window

your problem is in the power control feed. either the drivers or passengers switches are broken or the wire harness has a broken wire in it.

Posted on Aug 23, 2009

ajarema
  • 404 Answers

SOURCE: 2005 Mazda 3 low beams won't work - replaced

It can be either the relay (not the fuse) or it's the switch on the steering column.

Posted on Jan 02, 2010

  • 510 Answers

SOURCE: mazda eunos dash lights and rear lights not working

Check fuse f3 located in fascia fuse box,below steering wheel just above data link connection 15AMP
Fuse under bonnet f7 also connected to dash/rear lights,but if this blows you would have no indicators as well
good luck barry

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which fuse goes to tag lights on 98 ford explorer


Which fuse belong to license plate light or which number ...

www.fixya.com/cars/t10801433-fuse_belong_license_plate_light_or
Nov 11, 2011 - The licence plate lights are in the same line as your tail light wiring assembly. I assume your ... Previous owner cut wires going to lights for license plate. ... 1996 ford explorer license plate fuse ... 09@1998 ford f150 fuse box.

1997 Ford license plate lights are not working. - Ford Explorer ...

www.explorerforum.com > ... > Performance Lighting

Mar 13, 2011 - 5 posts - ‎4 authors
can anyone tell me why my lights would not be working on my license plate, i replaced old bulbs with new bulbs and checked every fuse and ... Parking lights stay on
19 posts
Sep 5, 2012
my tail lights wont work, and im out of ideas. i need help ...
18 posts
Sep 15, 2011
License Plate Lights
11 posts
Mar 24, 2011
trailer light problem
15 posts
Apr 22, 2009
More results from www.explorerforum.com

Dec 10, 2015 | Ford Cars & Trucks

1 Answer

2007 chevy equinox license plate light won't work after bulb and fuse replacement


Do the park lamps work ? license plate lights get power from same fuse ! Check ground wire ! use a volt meter an do voltage drop test ! Voltage Drop Testing The fuse for the license plate lights is in the under hood fuse box -engine compartment ! fuse #12 RT PRK LAMP 10Amp .

May 23, 2015 | 2007 Chevrolet Chevrolet Equinox LT

1 Answer

1 brake light doesn't work... good bulb and fuse


Lights are usually on a dual circuit! Left and right have separate fuses, check all fuses or check the fuse diagram on fuse cover or manual to identify correct fuse!

Dec 28, 2014 | 2001 Dodge Intrepid

1 Answer

Hi Everyone, I have a 2009


Bad grounded,u must ceck the signal (12V on the dash,empiric u can do it with a bulb and a wire,ceck every wire terminal under the dash instrument also the terminals from the back breaklight,eliminate the hipotese of a bad grounded instalation).Bad plugs (cleaning spray also helps).Main fuse/relay under the hood.Best guess:ceck the alternator charge rate can be overcharging making the bulbs /fuses/relays get burned.Inspect battery for acid over (overcharge signal).Ceck link alternator/starter/motor to chasis ground.Cheers,hope u deal the problem,let others know.

Oct 26, 2013 | Vauxhall Cars & Trucks

1 Answer

I have an 03 acura tl my headlight on the passenger side went out I checked fuses and the fuse was fine spent 100 for a new bulb replaced it and still didn't work and then on the same side my high beam...


check relay under the hood. also get a wire tester and check the wiring to theh eadlight and see if u have any juice going to it. if not then that is where your problem starts of tracing electric issue.

Jul 14, 2013 | Cars & Trucks

1 Answer

License plate lights arent working


You didn't forget to pull the headlight switch to check them? That's odd, usually license plate lights are spliced in from the tail light circuit.
There may be a separate ground for the license lights-if so, should be right nearby the bulbs. Use a test light or voltmeter and make sure fuse 22 has power. You could also check the sockets for power. If you have power to the socket and new bulbs don't work, it would be a grounding problem.

Jul 09, 2013 | Cars & Trucks

1 Answer

Mazda 6 sport sedan break lights not working after hid light conversion


Instructions Open the rear deck lid on the Mazda 6.Carefully remove the plastic finishing cover from the license plate light housing, using a small flat-head screwdriver to release the locking tabs. Pull the cover downward and off of the deck lid, exposing the license plate bulb.
Remove the old light bulb from the license plate bulb socket by hand. Wrap your new one in a paper towel and do not touch the bulb with your bare fingers. Insert the new bulb into the light socket. Install the finishing cover onto the light housing and push it upward until it clicks and locks into place.
Repeat Steps 2 and 3 to complete the LED light conversion on the opposite side of the deck lid. Test the new bulbs by turning on the headlights on the Mazda 6.
Mercedes Parts.






May 25, 2012 | 2004 Mazda 6

1 Answer

License plate light out of order


Get your hands on a manual......(OEM or Hanes, etc) either online or from someone who owns the same car. It's the only way to find the correct fuse to see if that's the problem.You could start by checking the color code of the wires to the light........then look for the same color back at the panel.....but that's a pain.Good luck, buddy!

Apr 12, 2012 | 2007 Audi A4 Convertible

1 Answer

My dome light will not work on my 1997 Lexus ES300. I've checked the fuse and have installed a new light bulb. No power


I know a website that has every info on all vehicles and vehicle problems(common/basic and technical both), with their solution In detail.. it's www.reliable-store.com

Mar 04, 2018 | 1997 Lexus ES 300

Not finding what you are looking for?
2005 Mazda 3 Sedan Logo

Related Topics:

369 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...