Question about Cars & Trucks
Clutch slave cylinder
Posted by Anonymous on
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Bleeding clutch slave cylinder
if you loosten the slave bleeder screw and push in the clutch pedal fluid should come out if not make sure someone holds down the pedal and tighten the screw then pump the clutch a few times and hold the pedal and open the screw if no fluid repeat a couple of times if still no fluid you need either a new master cylinder or just rebuild it( normally cheaper) and if you rebuild it make sure you flush all the lines of debris
Posted on Nov 12, 2008
I had the same problem with my 1995 1500 p.u.. Assuming your clutch slave cylinder is the concentric style. If not disregard. I hate that set up. what the hell was wrong with the old outside of the bell housing slave/ mechanical style fork and throw out bearing bla bla? Its because ford as well of the rest of the lovely auto makers decided long ago to make them as hard as hell to repair on you own. Ive been told theres a spsecial tool just for this bleeding task. Pobably. They make those tools to sell to us so they can further profit from us poor suckers.Also I wonder on your model if its concentric, does it have the difficult sized bleeder valve as mine did? or have they gotten a little more user friendly? doubt it. In my case as this style is a closed system I followed the bleeding intructions to a tee. That did get alot more clutch action for me, after 15 attempts.However I do believe the problem after looking and further inspection under the dash? look up under the dash and inspect your pedal rack and frame. I found mine was cracked and the cause of poor aliegnment. check for that rite away. I located another rack but before I got around to replacing it, the tranny blew, and the trucks sitting on my dads property. Its still a danmed good truck and one of these days I will get on it again. Anyway up untill the tranny blew I was never able to get more than half the distance from the pedal and besides the rack problem I would love to know the bleeding anser, that is if Im off target. Going to be up against it again when I replace that transmission. Hope this helps a little. Food for thought maybe? If you find out something more helpful post it so I will know too.
Posted on Dec 22, 2008
you have to bleed the air out of it. If there is not fluid leaking from the master cylinder on the firewall.it can leak on the inside of car or the out side if the master cylinder is bad.first make sure the reservoir stays full then open the bleeder on slave cylinder. this is called gravity bleeding. once fluid comes out, tighten bleeder, pump pedal one time loosen bleeder while holding clutch pedal down and then tighten. do this repeatedly until no air comes out. you can pump pedal several times,then hold and bleed however you like but I have better luck with individual pumps. just make sure that the lines hooked to slave cylinder are tight and there are no air leaks. and that the line does not go below the slave cylinder because sometimes air gets trapped in the lowest part of system.
Posted on Jan 12, 2009
SOURCE: bleeding the slave cylinder
Best to get the help of a friend to pump the clutch pedal for you.
Take care with the brake fluid, as it removes paintwork !
Top up your clutch fluid reservoir, connect a bleeding tube to the nipple on your slave cylinder, and put the other end of tube in a container.
Get your friend to pump pedal 3 times, and then hold to the floor.
Open the nipple for 5 seconds or so, then close.
Repeat this about 6 to 8 times topping up the fluid as you go.
You should then find, that the air is out of your system, and your pedal is back to normal !
Good luck !
A FixYa rating would be nice.... Thank you ! John.
Posted on Feb 10, 2009
I understand these cars have a sealed clutch system. When they fail you replace the whole kit master,hydrolic pipe and slave (comes in one piece). Search on ebay maybe £45 or so.
Posted on Feb 26, 2009
Tips for a great answer:
Dec 09, 2013 | Mazda 323 Cars & Trucks
Sep 07, 2013 | Cars & Trucks
Jun 09, 2013 | 1998 Dodge Avenger
Feb 17, 2011 | Ford Fiesta Cars & Trucks
Nov 05, 2010 | 1983 Mazda RX-7
Sep 12, 2010 | 2001 Mercury Cougar
Jul 28, 2010 | 1995 Ford Escort
Jul 12, 2010 | 1998 Ford Ranger SuperCab
Jul 11, 2009 | 1988 Mazda B2200
May 16, 2009 | 1988 Honda Accord 4 Door
Sep 25, 2017 | AC Cars & Trucks
21 people viewed this question
Usually answered in minutes!