Question about 2011 Dodge Nitro Heat

Open Question

Replace brake light bulb dodge nitro 2011

Brake light bulb burnt

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

johnny5846
  • 379 Answers

SOURCE: 2001 dodge neon tail lights inop

looking at your schematics and , you say tail lights don't work , you didn't mention if front parking lights and license plate lights are working , they all come from the same source , a black /yellow wire , a good clue if front work and rear don't , please advise .if fronts work then you have a open circuit somewhere between junction S118 (near breakout for left headlamp) and rear sockets.

Posted on Dec 31, 2008

fgainer
  • 54 Answers

SOURCE: 2004 dodge ram 1500 rear brake light out how to replace?

Open up the tail gate, you will see two torque screws on the inside beside the tail lights. take these out, this will free up the housing and you can change it from there.

Posted on Feb 01, 2009

  • 109 Answers

SOURCE: 2000 Dodge Stratus brake lights don't work

the stratus' are well known for the brakelight switch on the brake pedal going out frequently!!
so go to nearest parts house and buy a brakelight switch, that will most likely fix your problem!!
:-)

Posted on Jun 18, 2009

  • 3 Answers

SOURCE: Where is the fuse for rear brake lights on 2007

In the fuse box, under the hood on the drivers side. There is a detailed map of what fuses do what on the inside of the box cover.

Posted on Sep 05, 2009

abauto
  • 353 Answers

SOURCE: o2 Dodge Dakota Brake lights wont work but bulbs r good.

If the bulbs are good I would suspect the Brake light switch.

Brake Light Switch: Testing and Inspection
The brake lamp switch can be tested with an ohmmeter. The ohmmeter is used to check continuity between the pin terminals.
Switch Circuit Identification
- Terminals 1 and 2: brake lamp circuit
- Terminals 3 and 4: RWAL/ABS module and Powertrain Control Module (PCM) circuit
- Terminals 5 and 6: speed control circuit
Switch Continuity Test
NOTE: Disconnect switch harness before testing switch continuity.
With switch plunger extended, attach test leads to pins 1 and 2. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 3 and 4. Replace switch if meter indicates no continuity.
With switch plunger retracted, attach test leads to pins 5 and 6. Replace switch if meter indicates no continuity.


27c4c52.jpg

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get in the new lug studs from here 2011 dodge nitro the gap is too small for me to get them in at an angle


Remove the brake shoes. If there is still not enough room, you may have to remove the axle.

Dec 22, 2016 | 2011 Dodge Nitro

1 Answer

How do I replace the brake light bulb


1.Open the tailgate.
2. Locate the plastic plugs attached to the brake light housing (on the right side of the driver side light, on the left of the passenger side).
3. Carefully pry up the plugs with a screwdriver or other flat tool (I believe there are two).
4. The light should be free to pull out (pull toward the rear of the vehicle). You should see two torx screws.
5. Remove the bolts and pull the housing away from the tail light lens.
6. Twist and pull to remove the correct bulb.
7. Insert the new bulb into the holder and replace the housing.
8. Verify that the replacement bulb(s) are working.
9. Reinstall the torx screws and place the assembly back into it proper location on the vehicle.
10. Push the plugs back into the holes and verify that it is secure.
11. Close the tailgate and check for proper fitment.

May 12, 2014 | 2011 Dodge Nitro Heat

1 Answer

How can I replace the brake light bulb


make sure to replace both at the same time otherwise you will have one bright and one dim bulb

May 12, 2014 | 2011 Dodge Nitro Heat

1 Answer

Left and 3rd brake light is not working on 2007 Dodge Nitro.


it might be a resistor or just the bulbs or sockets bad.

Apr 13, 2012 | 2007 Dodge Nitro R/T

2 Answers

Both brake lights went out at the same time i changed the bulbs but the brake lights still wont light up when i depress the brakes but my rear lights still work


ok so what your saying is that the tail lights still work but no brake lights work, you've replaced the bulbs, next step is to check the fuse for the brake lights, if its bad just replace it, if its good, you need to check the brake light switch thats located at the top of the brake pedal arm, ( up under the dash where the brake arm attaches to the mount, you will see a switch,,, sometimes they just get stuck, so depress the brake and see if the switch is moving at all, if not, remove the switch and replace it as long as the adjustment looked to be correct.

Sep 10, 2011 | 2008 Dodge Nitro

1 Answer

When I press the brake pedal only the left brake light comes on. The bulbs are good and the fuses are all good. Replace the right light modual but still no help. this is on a 2008 Dodge Nitro


How do you know the bulb is good? Even if it uses the same bulb as the tail light it is always a different filiment. But if you tried replacing the bulb and the fuse than it has to be the wiring. If it's a 2008 it should be covered by the warranty, I would bring it into the dealer.

Aug 17, 2011 | 2008 Dodge Nitro

1 Answer

Need to remove brake light cover to replace brake light bulb


No, you need to pull back the Cardboard trunk liner from behind the light assembly and remove the bulb from the socket. You should have to give it a turn counter clockwise to get the holder to release. If the light cover were removeable you would be able to see the screws from the outside or the release points along the edges.

Oct 16, 2010 | 2008 Dodge Nitro

2 Answers

Need to change brake light on 2007 Nitro,


To Access The Brake Light Youll Need To Remove Carper Or Panel Opposite Of The Light. I Am Referring To The Inside Of The Vehicle Referred To As The Trunk Or Rear Storage. Once You Remove The Panel Or Carpet you Will Have Full Access To The Lights. Find The Light That Is Burnt Out By Turning On All The Lights From The Inside You Can See The Light In The Harness Not Working.
Next Grasp The Rear Of The Holder Twist And Pull.
A New Light Can Be Found At Any Auto Parts Store.

Jan 19, 2009 | 2007 Dodge Nitro R/T New Cars

Not finding what you are looking for?
2011 Dodge Nitro Heat Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...