Question about Cars & Trucks

Open Question

Caterpillar Forklift P5000 Lp

Having problem's finding solution on fixing the problem because it will start and run for aproximantly 8 to 10 seconds then shut down it also has had a new main injector changed out in it also has a real dime mil light on for battery had alternator checked out it was fine also had ECM checked out it also was fine how might I go about fixing this problem

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

280zlvr
  • 126 Answers

SOURCE: 2004 lly duramax

try hooking up a fuel pressure test gauge to fuel rail pre filter and post filter and rev truck to 2500 rpm what is fuel pressure ?
next using a vacume pump attach to fuel pressure regulator pump up while engine is running only pump up to 8 psi to see if pressure changes if not replace pressure regulator .
it could also be ur speed sensor switch on overdrive transmission
good luck with it

Posted on Jun 30, 2008

  • 1 Answer

SOURCE: My 1994 suburban engine stops. No fuel, no MIL light.

I checked all of the fuseable links and they were all good. Next I decided to check all the power wires to the ECM and also the grounds from a wiring diagram because the Mil is controlled by the ecm and the bulb was good. The ecm is located behind the glove box. Bingo, the orange wire was only reading 3-5 volts at the ECM, but 12.5 volts after the fuseable link at the underhood fuse block (passenger side firewall). I ran a temp wire directly from after the fuseable link to the orange wire at the ecm and the ecm turned back on and the Mil or "check engine soon" light came on too. The truck started up and has never run smoother.

Note that at first the truck just stalled out and I could restart it right away with no error codes. Eventually the stalling became more frequent with longer reset times required. Once it threw a "code 54" and I thought it was fuel related as each time the gas stopped and I could still start the truck with gas poured into the TB. Ignition ok. My fuel pump turned on and ran if I tested it. I even checked the pressure regulator and the fuel filter to no avail.The orange wire that powers up the ecm is technically part or the fuel pump relay circuit as it also feeds the fuel pump relay 12.5 volts all the time. The thin orange wire from the fuse block is joined to two other thin orange wires in the large group of wires that heads to the ecm along the firewall behind the engine. I had to dig it out of the many wires to find it and remove a lot of tape. It is amazing to me that this one little orange wire could cause so much grief and be so hard to track down. I could not have afforded to take this problem to the Dealer.

Posted on Mar 26, 2009

  • 740 Answers

SOURCE: 1993 honda accord 2.2,no injector pulse

This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA

Posted on May 15, 2009

  • 1 Answer

SOURCE: 96 Grand Am SE2 2.4L starts and dies immediately

I had the SAME thing with my car!! Remove your air bag module its a grayish looking box that deploys your air bags, my air bag light was on but it was on and off. I pumped gas in my car one night and when i went to crank it my car cut right off after a split second. My mechanic took time on it but discover that it was a secrity issue. He removed the air bag module and presto it fired right up. I thought it was a fuel filter or fuel pump. It was just the air bag module, people freaked out about it once i told them what it was....it should be under the passenger seat, i believe u may have to take out the seat to get to it.

Posted on Jun 26, 2009

  • 5 Answers

SOURCE: 1987 Chevrolet S-10 Pickup1987 chevy s10 2.5l tbi

Check the trottle body postioning sensor...

Posted on Jul 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need a service / maintenance manual please.


White Forklift - Cricket and Golf

www.cricketandgolf.com/white-forklift.html
White Mobilift Fork Lift Trucks MY 40, 50, 60, And 70 Operator's Manual ... White Forklift, MY-20, 25 and 30 Parts, Overhaul and Operators Manuals! $99.0.

Jul 26, 2015 | Cars & Trucks

1 Answer

How do you clear error codes on a p5000 cat forklift?


-The problem need to be fix before clear the code.


Good Luck


Mai

Oct 10, 2014 | Cars & Trucks

1 Answer

Cat P5000 forklift head gasket failure


You should have the head it's self pressure tested when it is off the engine it may cracked .

Feb 11, 2014 | Cars & Trucks

1 Answer

VALVE SETTINGS FOR KOMATSU 4D95 FORKLIFT


http://biondorentals.com.au that is one place where you can find the solution of your forklift truck problems.

Aug 21, 2013 | Cars & Trucks

1 Answer

Can I bypass the A/c pump?


most veh's you can but it depends on the position of the tensioner pulley (if it has one) if it does'nt have a tensioner pulley,and it's tightened by the alternator then should'nt have a problem take a piece of string and run around the other pulleys and measure it to get the aproximate length you would need.

Sep 07, 2012 | 1996 Mercury Grand Marquis

1 Answer

Mitsubishi outlander 4x4 - 2005 light stays on when changing from 4x4 to 2 wheel drive


Try this quick fix solution.
Put vehicle in park or neutral, press the switch or turn the dial to 2H, put vehicle in reverse and reverse the vehicle aproximately 10m's or around 30ft.
Now drive vehicle forward, and this should unlock the 4wd mode.
If this doesn't work then your solenoid may need replacing.

Jul 31, 2011 | 2005 Mitsubishi Outlander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...