Question about 2002 Mercury Mountaineer

Open Question

Seat belt wont latch - 2002 Mercury Mountaineer

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: MERCURY GRAND MARQUIS 2004 SEAT BELTS WILL NOT LATCH

Clean the cookie crumbs out of the receiving end of the seat belts. Not even kidding. You need some high pressure air. Or a pressure washer (ask around - pressure washer owners always are looking for a reason to use those things).
I'm not being funny, if the belts won't latch, something is clogging the latch. Unless the male end of the belt is too short, or the receiving end is too short, and they just don't reach. In which case the operator my be the issue.

Posted on Aug 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seat belt receiver


i've seen this before on car rear seats but not a truck but i guess it could happen as well the middle belt latch gets twisted/mixed up with the passenger side belt latch , mfg's use a different size belt for the middle passenger belt and it won't latch up with the passenger side belt reciever but does fit inside

ck that i'll bet thats it

Oct 20, 2013 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

I have an 03 lincoln navigator the driver seat wont go forward or backward it can only go up and down, but every time touch the switch i hear a click, what can be my problem and what can be done to solve...


Most Ford products are designed so the seat belt latch by the center console moves with the seat. The bottom of the latch rides on the seat rail, and with time sometimes it builds up a little play on the rail. As the seat moves forward or back, the seat belt guide often tilts forward or back, just a bit, on the rail, and gets stuck. So you can move forward or back just a bit, but then it jams and you can hear the motor, but can go no further.

The long term fix is to remove the seat, disassemble the seat belt guide and rail, and usually replace some parts.

But the short term solution is often to simply hold on to the seat belt latch and rock it forward and away from the seat as you try to go forward or back. Or, sometimes it works best to rock it backwards and away from the seat as you try to move forward or back. It all depends on which way it is binding.

There's no guarantee that it won't jam again if you move it all the way back or forward, but once you find the right position to hold the seat latch in while moving the seat, you should be able to re-adjust it where you need it to be.

Aug 23, 2013 | Cars & Trucks

1 Answer

Back seat belt wont lock


Check to be sure it is the right belt and latch combination.
I believe you have 3 seat belts in the rear. The latch for the two side ( door) belts is not the same as the one in the middle.
VERY often, one of the latches will fall down in between the seat rest and the back rest of the seat, often from dis-use.
This happens on all cars.
You should have 3 latches on short straps in the middle of the rear seat.
Be blessed.

Feb 02, 2013 | 1999 Subaru Legacy

1 Answer

How to replace rear side glass the one behind the vented glass on two door model


Removal Procedure
    Caution: When working with any type of glass or sheet metal with exposed or rough edges, wear approved safety glasses and gloves in order to reduce the chance of personal injury.
    Important: Before cutting out a stationary window, apply a double layer of masking tape around the perimeter of the painted surfaces and inner trim of the window.
  1. Use safety glasses and gloves.

  2. 392924.gif
    tif.gif
  3. Carefully spread the handle retainer outward in order to release the latch pin from the latch.
  4. Remove the latch pin from the latch.
  5. Remove the seat belt retractor. Refer to Front Seat Belt Replacement in Seat Belts.
  6. Open the door in order to access the rivets.
  7. Drill out the rivets retaining the window assembly.
  8. Thoroughly clean all metal particles that may have lodged inside the body panel.
  9. Remove the window assembly from the vehicle.
Installation Procedure

    392924.gif
    tif.gif
  1. Install the window assembly to the vehicle.
  2. Using the J 34940 (or equivalent), install the rivets in order to retain the window assembly to the vehicle.
  3. Install the seat belt retractor. Refer to Front Seat Belt Replacement in Seat Belts.
  4. Install the latch pin.
  5. Using a punch, carefully drive the pin into the latch.

Sep 15, 2011 | 2000 Chevrolet Blazer

1 Answer

The seat belt beeper wont shut off soon as u put car in gear it starts beeping how can i unplug it for now


Try latching all the seat belts and see if it still does it. The front ones at least have sensors on them.

Jun 10, 2011 | 1996 Buick Park Avenue

1 Answer

I have an 05 ford escape... has never been in a wreck or any run in at all. the seat belt buckle for some reason wont latch and im not sure if somehow the pretensioner was activated or not. im guessing...


Unless there is a recall on the seat belt Ford is not going to replace a 12 year old seat belt free of charge. I doubt that the part is even available from Ford anymore unless that particular part is still used on a newer vehicle.

Apr 16, 2017 | 2005 Ford Escape

1 Answer

I have a 2003 2 door sunfire. I am installing a infant car seat base using the latch system instead of the seat belt. Can I do this in the middle of the back seat or does it have to go at one of the...


Ideally if there is a middle set of latches in the seat, you can install an infant car seat base there. If the seat has any kind of hump or other irregularity then it should not be installed there. Although the middle of the back seat is safest for a child, most vehicle do not have a latch system there. However most cars do have a lap belt for the center seat and that should be used if you decide to place your car seat.

Do not use the latches from either side of the right back and left seat. The latch system is designed to be a specific distance apart to work correctly. If you don' want to use the lap belt then you should put the child seat on either the left or right back seat using the latch system.

Aug 18, 2010 | 2003 Pontiac Sunfire

1 Answer

Seat belt wont move


you probably need to be mechanically inclined to fix this problem. When the shoulder strap stopped working on mine the switch that is operated by the door latch had to be serviced. ie: the door will have to be taken apart to access the switch.

Jun 17, 2009 | 1987 Toyota Camry

Not finding what you are looking for?
2002 Mercury Mountaineer Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

fordexpert

Level 3 Expert

5470 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...