Question about 2001 Lincoln LS

1 Answer

Fuel pump assembly - 2001 Lincoln LS

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Lincoln Master
  • 21,873 Answers

The fuel pump is in the gas tank.
What is your question ?

Posted on Apr 30, 2013

Testimonial: "I was searching that topic but didn't mean to post a question...oops "

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How would I replace my fuel Filter


The fuel filter is an integral component of the fuel pressure regulator, which is mounted on top of the fuel pump module, located in the fuel tank. When the fuel filter/regulator assembly requires service, the fuel tank must be removed from the vehicle, however, the fuel pump module does not need to be removed.
  1. Disconnect the battery ground cable.
  2. You dont have to relieve your fuel systems pressure because your jeep has an automatic bleeder.
  3. Remove the fuel tank assembly.
  4. Clean the area around the fuel filter/regulator.



0900c152800a96ce.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 5: Remove the fuel filter/pressure regulator retaining clip from the top of the assembly


0900c152800a96cf.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 6: Replace the old fuel filter/pressure regulator mounting gasket

  1. Disengage the retaining clamp from the top of the filter/regulator assembly. Discard the retaining clamp.
  2. Using 2 small prying tools, pry the filter/regulator assembly out from the top of the fuel pump module. The filter/regulator assembly will unsnap from the fuel pump module.
  3. Remove and discard the mounting gasket below the filter/regulator.
  4. Before discarding the fuel filter/pressure regulator assembly, inspect the assembly to verify that the O-rings are intact. If the smallest of the 2 O-rings cannot be found on the bottom of the filter/regulator, it may be necessary to remove it from the fuel inlet passage in the fuel pump module.

To install:


0900c152800a96d0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 7: Check the condition of the fuel filter/pressure regulator O-rings

  1. Clean the recessed area in the pump module where the filter/regulator assembly is to be installed.
  2. Check the replacement filter/regulator assembly to make sure that the new O-rings are already installed on the assembly.
  3. Apply a small amount of clean engine oil to the O-rings.
  4. Install a new gasket on top of the fuel pump module.
  5. Press the new fuel filter/pressure regulator assembly into the top of the fuel pump module until it snaps into position (a positive click must be heard or felt).
  6. The arrow on top of the fuel pump module should be pointed towards the front of the vehicle (12 O&rsquoclock position).
  7. Turn the filter/regulator assembly until the supply tube (fitting) is pointed to the 11 O&rsquoclock position.
  8. Install new retainer clamp (the clamp snaps over the top of the filter/regulator and locks to the flanges on the pump module).
  9. Install the fuel tank assembly.
  10. Connect the negative battery cable.

Jan 28, 2011 | 1996 Jeep Grand Cherokee

3 Answers

Do I have to drop the fuel tank to replace the fuel pump on a 94 Buick le saber


Yes ,,instructions are below, Use eye protection for this procedure
Remove or Disconnect:

  1. Relieve Fuel Pressure
  2. Disconnect negative battery cable
  3. Raise vehicle on hoist
  4. Remove Fuel Tank
  5. Remove Fuel Gage sending and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel gage sender unit.
  6. Disconnect pump wires, hose clamps, and clamp around pump body
  7. Pull pump assembly out of rubber connectors
  8. Inspect fuel pump attaching hose for any signs of deterioration. Replace as necessary.
Install or Connect:

  1. Push fuel pump assembly into attaching hose
  2. Connect pump wires, hose clamps at attaching hose and around pump body
  3. Place Fuel tank sending unit and pump assembly into tank using new O-ring
  4. Place cam lock over assembly and lock by turning clockwise
  5. Install Fuel Tank
  6. Start engine and check fuel pipe connector for visual leaks

Oct 20, 2010 | 1994 Buick LeSabre

1 Answer

Where is the fuel pump located ? Is it in the tank?


The fuel pump assembly is located in the fuel tank. Refer to the fuel tank assembly illustrations in this section. On most applications, the fuel tank must be lowered to remove the fuel pump assembly. The fuel pump assembly is cooled by the fuel in the tank.
REMOVAL & INSTALLATION

See Figure 1
  1. Before disconnecting the fuel lines or any of the fuel system components, release the fuel system pressure as described previously in this section. Releasing system pressure is a very important step for the correct removal of the electric fuel pump.
    1. Disconnect the negative battery cable. Unfasten the fuel pump assembly electrical connector and remove the fuel tank inspection cover.

    If the truck has no fuel tank inspection cover, the fuel tank must be lowered or removed to gain access to the in-tank fuel pump.
    1. Disconnect the fuel outlet and return hoses. Remove the fuel tank assembly, if necessary.
    2. Remove the ring retaining bolts and the O-ring, then lift the fuel pump assembly from the fuel tank. Plug the opening with a clean rag to prevent dirt from entering the system.

    When removing or installing the fuel pump assembly, be careful not to damage or deform it. Always install a new O-ring.
    To install:
    1. Install the fuel pump assembly in the fuel tank with a new O-ring. Install the ring retaining bolts. Install the fuel tank if removed.
    2. Reconnect the fuel lines and fasten the electrical connection.
    3. Connect the battery cable, then start the engine and check for fuel leaks.

    The "Check Engine Light'' may stay on after installation is completed. If so, the trouble code in the control unit's memory must be erased. To erase the code, disconnect the battery cable for 10 seconds, then reconnect it a verify that the light is extinguished.
Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Sep 07, 2010 | 1990 Nissan Pathfinder

3 Answers

Where is fuel pump


Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:
  5. While holding the modular fuel sender assembly down, remove the snapring, if equipped or if equipped with a cam lock ring use Fuel Sender Lock Nut Tool J-39765 to press down and rotate the cam lock ring to remove it.
    WARNING If the modular fuel sender assembly is retained by a snapring, it may spring up from its position. When removing the modular fuel sender from the tank, be aware that the reservoir bucket is full of fuel. It must be tipped slightly during removal to avoid damage to the float.
    Fuel sender assembly External fuel strainer Connector retainer from the wiring harness and the fuel pump
  6. Gently release the tabs on the sides of the fuel sender at the cover assembly. Begin by squeezing the sides of the reservoir and releasing the tab opposite the fuel level sensor. Move clockwise to release the second and third tab in the same manner.
  7. Remove or disconnect the following:
    Fuel pump electrical connection by lifting the cover assembly Baffle and pump assembly from the retainer by rotating the fuel pump baffle counterclockwise Fuel pump outlet by sliding it out of slot Fuel pump outlet seal
To install:


88dac81.jpg
Fig. Exploded view of the fuel sender assembly mounting to the tank


4a62e9e.jpg
Fig. Exploded view of the fuel pump assembly
  1. Install or connect the following:
    NOTE Gently pull on the fuel pump reservoir to assure it is secure. If not secure, replace the entire fuel sender.
    Fuel pump outlet with a new seal by sliding it in the reservoir cover slots Fuel pump and baffle assembly onto the reservoir retainer by rotating it clockwise until seated Lower retainer assembly partially into the reservoir by aligning all 3 sleeve tabs and pressing the retainer onto the reservoir making sure all 3 tabs are firmly seated
    Connector retainer to the wiring harness and the fuel pump External fuel strainer Snapring, if equipped to the retainer slots while holding the modular fuel sender assembly down or use Fuel Sender Lock Nut Tool J-39765 in order to install the cam lock ring Fuel tank Negative battery cable
  2. Pressurize the fuel system and verify no leaks.

Hope helps (remember rated and comment this).

Aug 11, 2010 | 2001 Pontiac Grand Am SE

1 Answer

How to change the fuel pump on a 1996 Pontiac Transport


For 1996 Pontiac Truck Trans Sport 3.4L SFI 6cyl check this procedure for Fuel Pump... there are two different electric fuel pumps used:
- A medium pressure twin turbine pump for vehicles equipped with Throttle Body Injection (TBI). - A high pressure roller vane pump for vehicles equipped with Sequential Fuel Injection (SFI).
(see Figure 1)


d7f6f20.jpg


Fig. 1: View of the fuel pump assembly and related components
The fuel pump is mounted to the fuel sender assembly inside the fuel tank. The fuel is pumped to the engine at a specified flow and pressure by the fuel pump. Excess fuel is returned to the fuel tank by the return pipe. The fuel pump delivers a constant flow of fuel to the engine even during low fuel conditions and aggressive vehicle maneuvers.

CAUTION When working on or near the fuel tank, be sure to observe the information molded on the bottom of the tank.
Removal & Installation
  1. Disconnect the negative battery cable.
  2. Properly relieve the fuel system pressure.
(see Figure 2)


42fbc79.jpg

Fig. 2: Exploded view of the fuel pump-to-tank mounting components
  1. Drain and remove the fuel tank.
  2. Remove the fuel sender assembly.
  3. Disassemble the fuel pump strainer and the fuel pump: Note the position of the strainer in relation to the pump.
(see Figure 3)


c8d9af6.jpg


Fig. 3: Remove the fuel tank locking ring with a non-sparking (brass) punch.
  1. Support the fuel pump in one hand, and grab the strainer in the other hand.
    1. Rotate strainer in one direction and pull off pump. Discard strainer.
(see Figure 4)


3c2e4a1.jpg


Fig. 4: Exploded view of the fuel pump components
    1. Remove deflector.
  1. Disconnect the fuel pump electrical connector.
  2. Loosen the two connecting clamps, if equipped.
  3. Place the fuel sender assembly upside down on the work bench.
    1. Pull the fuel pump downward to remove it from the mounting bracket, then tilt the pump outward and remove it from the connecting hose or the fuel pulse dampener.
  4. It is recommended to replace the hose and clamps, if equipped.
CAUTION Do not run the pump unless submerged in fuel
To install:
  1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body, where equipped.
  2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.

Hope this help (remember rated this).

Jun 04, 2010 | 1996 Pontiac Trans Sport

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

1 Answer

HOW TO TAKE A FUEL PUMP OUT A 2001 ISUZU TROOPER


REMOVAL PROCEDURE

  1. Disconnect the negative battery cable.
  2. Drain all the fuel from the tank.
  3. Install and tighten the drain plug. Tighten Tighten the drain plug to 20 N.m (14 lb ft.) .
  4. Remove the fuel tank.
  5. Remove the retaining screws from the fuel tank.
  6. Remove the fuel pump assembly from the fuel tank.
    1. Cover the fuel pump opening in order to prevent dust, dirt, or debris from entering the fuel tank.
    INSTALLATION PROCEDURE

    1. Install the fuel pump assembly. Tighten Tighten the fuel pump assembly mounting bolts to 3 N.m (27 lb ft.) .
    2. Install the fuel pump assembly retaining screws.
    3. Install the fuel tank assembly.
    4. Fill the tank with fuel.
    5. Tighten the fuel filler cap.
      1. Connect the negative battery cable.
      REMOVAL PROCEDURE # 2
      REMOVAL

      CAUTION: When repair to the fuel system has been completed, start engine and check the fuel system for loose connection or leakage. For the fuel system diagnosis, see Computers and Control Systems/System Diagnosis.

      1. Disconnect battery ground cable.
      2. Loosen fuel filler cap.
      3. Drain fuel. Tighten drain plug to the specified torque after draining fuel. Torque: 20 N.m (14 lb ft) - M8
      4. Remove fuel tank assembly (1).
      5. Remove fuel pump (FP) assembly (2) fixing screws and remove the FP assembly.
      NOTE: After removing FP, cover fuel tank to prevent any dust entering.
      INSTALLATION
      1. Install FP assembly (2).
      2. Install fuel tank assembly (1).
      3. Fill the tank with fuel and tighten fuel filler cap.
      4. Connect battery ground cable.

Oct 18, 2009 | 2001 Isuzu Trooper

1 Answer

How to replace fuel pump 91 lesabre


Removal & Installation The fuel pump is located in the fuel tank. The fuel tank must be removed from the vehicle in order to access the pump.
  1. Properly relieve fuel system pressure.
  2. If not already done, disconnect the negative battery cable.
  3. Raise and safely support the vehicle.
  4. Safely drain and remove the fuel tank assembly, as outlined later in this section.
  5. If necessary, detach the quick-connect fittings from the fuel sender assembly and remove the fuel lines.
  6. Remove the fuel gauge sender and pump assembly by turning the cam locking ring counterclockwise. It may be necessary to use a spanner wrench, such as tool J-24187, to perform this.
  7. Carefully lift the assembly from the fuel tank, then remove the fuel pump from the fuel gauge sender unit.
  8. Remove the sender O-ring from the top of the sender and discard.
  9. Disconnect the pump wires, hose clamps and the clamp from around the pump body.
  10. Pull the pump assembly out of the rubber connectors.
  11. Inspect the fuel pump attaching hose for any signs of deterioration, and replace as necessary.
  12. To install:
    1. Push the fuel pump assembly into the attaching hose. Attach the pump electrical wires and fasten the hose clamps to the attaching hose and around the pump body.
    2. Place the fuel tank sender and pump assembly into the fuel tank. Use a new O-ring seal during assembly.
    3. Place the cam lock over the assembly, then lock by turning clockwise, using a suitable spanner wrench, if necessary.
    4. If removed, attach the fuel sender fuel line quick-connect fittings.
    When installing the fuel tank, make sure all rubber sound isolators or anti-squeak spacers are replaced in their original locations.
    1. Install the fuel tank, as outlined later in this section.
    2. Refill the fuel tank.
    3. Connect the negative battery cable.
    4. Turn the ignition switch to the ON position to pressurize the fuel system and check for leaks.

Oct 10, 2009 | 1991 Buick LeSabre

2 Answers

Want to replace fuel pump need help to where its at and how to do


Fuel pump is located inside the fuel tank access cover location. Here's the details:

  1. Properly relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Open the rear access door.
  4. Release the catch for the back seat and tilt the seat out of the way.
  5. Move the carpet behind the seat that covers the fuel pump access panel.
  6. Disconnect the fuel pump electrical connectors.
  7. Remove the screw securing the ground wire.
  8. Remove the four screws securing the fuel pump access panel and position it out of the way.
  9. Remove the hose clamps connecting the fuel hoses to the fuel pump.
  10. Disconnect the fuel hoses from the fuel pump.
  11. Disconnect the fuel tank pressure sensor electrical connector.
  12. Remove the eight retaining screws securing the sender assembly to the tank.
    WARNING The fuel assembly is easily damaged. Use care when removing the assembly from the tank.
  13. While twisting and tilting, gradually lift the fuel sender assembly and remove from the tank.
  14. Wrap the fuel pump assembly in a rag before removing the assembly from the vehicle.
  15. Cover or seal the fuel tank until installing the fuel pump assembly.
  16. Remove the retaining hardware that holds the sender to the fuel pump assembly.

To install:
  1. Install the retaining hardware that holds the sender to the fuel pump assembly.
  2. Remove the temporary covering or seal that was used to protect the tank.
  3. Install the fuel pump into the access port on top of the fuel tank.
  4. Carefully, twist the fuel pump as necessary to properly position it in the fuel tank.
  5. Install the eight retaining screws securing the sender assembly to the tank.
  6. Connect the two fuel hoses to the pump and secure with clamps.
  7. Connect the fuel tank pressure sensor electrical connector.
  8. Insert the ground wire and fuel pump electrical connector through the access hole and install the access cover.
  9. Connect the fuel pump electrical connector.
  10. Secure any loose wiring with adhesive tape and reattach the carpeting.
  11. Release the catch for the rear seat and put the rear seat in the normal position.
  12. Close the rear access door.
  13. Reconnect the negative battery cable.
I can help you further and show you where you can access the information for free. Good luck!

Apr 28, 2009 | 2000 Kia Sportage

2 Answers

I am not getting fuel to my engine


Removal
  1. Relieve the Fuel System Pressure . Refer to the procedure in this section.
Cushion Cover and Pad, Rear Seat — One-Piece and 50/50 Split Fold Removal
  1. Remove the two rear seat cushion bolts.
  1. Fold the rear seat back cover and cushion (60084) forward.
  1. Carefully pull the rear seat cushion and cover (60030) out from under the rear seat back cover and cushion and remove the rear seat cushion and cover from the vehicle
  1. Remove the rear seat cushion and cover (60030). Refer to Section 01-10 for the removal procedure.
  1. Remove the three luggage compartment floor cover hold-down pins and fold the luggage compartment floor cover (45455) forward until the fuel pump assembly access plate is visible.
  1. Remove the four fuel pump assembly access plate screws, the ground lead, and the fuel pump assembly access plate from the chassis.




  1. Disconnect the fuel pump assembly electrical connector.




  1. On 4-door vehicles, remove the fuel vapor tube shutoff valve bolt and the evaporative emission tube shut off valve (9G332) from the bracket on the fuel pump assembly housing.




  1. Loosen the two hose clamps and disconnect the two fuel pump hoses from the fuel pump hose fittings on the fuel pump assembly housing.




  1. Remove the four screws (2-door) or eight screws (4-door) and lift the fuel pump assembly housing from the fuel tank (9002).




  1. Disconnect the fuel level sensor electrical connector.
  1. Remove the two fuel level sensor washers and fuel level sensor nuts and the fuel level sensor.



-------------------------------------------------------------------------------------
Section 10-01: Fuel Tank, Filters, Lines and Electric Fuel Pump 1996 Aspire Workshop Manual
REMOVAL AND INSTALLATION Fuel Pump Removal
  1. Remove the fuel level sensor. Refer to the Fuel Level Sensor removal procedure in this section.
  1. Remove the fuel pump screw, fuel pump grommet and the fuel pump bracket from the bottom of the fuel pump (9350).




  1. Remove the fuel tank sender filter bracket, fuel tank sender filter (9A011) and the fuel tank sender filter retainer from the fuel pump.
  1. Disconnect the fuel pump electrical connector.
  1. Remove the clamp and the fuel pump from the fuel pump assembly housing.

Apr 19, 2009 | 1995 Ford Aspire

Not finding what you are looking for?
2001 Lincoln LS Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...